1/* 2 * Copyright (C) 2013 Broadcom Corporation 3 * 4 * This program is free software; you can redistribute it and/or 5 * modify it under the terms of the GNU General Public License as 6 * published by the Free Software Foundation version 2. 7 * 8 * This program is distributed "as is" WITHOUT ANY WARRANTY of any 9 * kind, whether express or implied; without even the implied warranty 10 * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 11 * GNU General Public License for more details. 12 */ 13 14#include <linux/device.h> 15#include <linux/kernel.h> 16#include <linux/module.h> 17#include <linux/sched.h> 18#include <linux/i2c.h> 19#include <linux/interrupt.h> 20#include <linux/platform_device.h> 21#include <linux/clk.h> 22#include <linux/io.h> 23#include <linux/slab.h> 24 25/* Hardware register offsets and field defintions */ 26#define CS_OFFSET 0x00000020 27#define CS_ACK_SHIFT 3 28#define CS_ACK_MASK 0x00000008 29#define CS_ACK_CMD_GEN_START 0x00000000 30#define CS_ACK_CMD_GEN_RESTART 0x00000001 31#define CS_CMD_SHIFT 1 32#define CS_CMD_CMD_NO_ACTION 0x00000000 33#define CS_CMD_CMD_START_RESTART 0x00000001 34#define CS_CMD_CMD_STOP 0x00000002 35#define CS_EN_SHIFT 0 36#define CS_EN_CMD_ENABLE_BSC 0x00000001 37 38#define TIM_OFFSET 0x00000024 39#define TIM_PRESCALE_SHIFT 6 40#define TIM_P_SHIFT 3 41#define TIM_NO_DIV_SHIFT 2 42#define TIM_DIV_SHIFT 0 43 44#define DAT_OFFSET 0x00000028 45 46#define TOUT_OFFSET 0x0000002c 47 48#define TXFCR_OFFSET 0x0000003c 49#define TXFCR_FIFO_FLUSH_MASK 0x00000080 50#define TXFCR_FIFO_EN_MASK 0x00000040 51 52#define IER_OFFSET 0x00000044 53#define IER_READ_COMPLETE_INT_MASK 0x00000010 54#define IER_I2C_INT_EN_MASK 0x00000008 55#define IER_FIFO_INT_EN_MASK 0x00000002 56#define IER_NOACK_EN_MASK 0x00000001 57 58#define ISR_OFFSET 0x00000048 59#define ISR_RESERVED_MASK 0xffffff60 60#define ISR_CMDBUSY_MASK 0x00000080 61#define ISR_READ_COMPLETE_MASK 0x00000010 62#define ISR_SES_DONE_MASK 0x00000008 63#define ISR_ERR_MASK 0x00000004 64#define ISR_TXFIFOEMPTY_MASK 0x00000002 65#define ISR_NOACK_MASK 0x00000001 66 67#define CLKEN_OFFSET 0x0000004C 68#define CLKEN_AUTOSENSE_OFF_MASK 0x00000080 69#define CLKEN_M_SHIFT 4 70#define CLKEN_N_SHIFT 1 71#define CLKEN_CLKEN_MASK 0x00000001 72 73#define FIFO_STATUS_OFFSET 0x00000054 74#define FIFO_STATUS_RXFIFO_EMPTY_MASK 0x00000004 75#define FIFO_STATUS_TXFIFO_EMPTY_MASK 0x00000010 76 77#define HSTIM_OFFSET 0x00000058 78#define HSTIM_HS_MODE_MASK 0x00008000 79#define HSTIM_HS_HOLD_SHIFT 10 80#define HSTIM_HS_HIGH_PHASE_SHIFT 5 81#define HSTIM_HS_SETUP_SHIFT 0 82 83#define PADCTL_OFFSET 0x0000005c 84#define PADCTL_PAD_OUT_EN_MASK 0x00000004 85 86#define RXFCR_OFFSET 0x00000068 87#define RXFCR_NACK_EN_SHIFT 7 88#define RXFCR_READ_COUNT_SHIFT 0 89#define RXFIFORDOUT_OFFSET 0x0000006c 90 91/* Locally used constants */ 92#define MAX_RX_FIFO_SIZE 64U /* bytes */ 93#define MAX_TX_FIFO_SIZE 64U /* bytes */ 94 95#define STD_EXT_CLK_FREQ 13000000UL 96#define HS_EXT_CLK_FREQ 104000000UL 97 98#define MASTERCODE 0x08 /* Mastercodes are 0000_1xxxb */ 99 100#define I2C_TIMEOUT 100 /* msecs */ 101 102/* Operations that can be commanded to the controller */ 103enum bcm_kona_cmd_t { 104 BCM_CMD_NOACTION = 0, 105 BCM_CMD_START, 106 BCM_CMD_RESTART, 107 BCM_CMD_STOP, 108}; 109 110enum bus_speed_index { 111 BCM_SPD_100K = 0, 112 BCM_SPD_400K, 113 BCM_SPD_1MHZ, 114}; 115 116enum hs_bus_speed_index { 117 BCM_SPD_3P4MHZ = 0, 118}; 119 120/* Internal divider settings for standard mode, fast mode and fast mode plus */ 121struct bus_speed_cfg { 122 uint8_t time_m; /* Number of cycles for setup time */ 123 uint8_t time_n; /* Number of cycles for hold time */ 124 uint8_t prescale; /* Prescale divider */ 125 uint8_t time_p; /* Timing coefficient */ 126 uint8_t no_div; /* Disable clock divider */ 127 uint8_t time_div; /* Post-prescale divider */ 128}; 129 130/* Internal divider settings for high-speed mode */ 131struct hs_bus_speed_cfg { 132 uint8_t hs_hold; /* Number of clock cycles SCL stays low until 133 the end of bit period */ 134 uint8_t hs_high_phase; /* Number of clock cycles SCL stays high 135 before it falls */ 136 uint8_t hs_setup; /* Number of clock cycles SCL stays low 137 before it rises */ 138 uint8_t prescale; /* Prescale divider */ 139 uint8_t time_p; /* Timing coefficient */ 140 uint8_t no_div; /* Disable clock divider */ 141 uint8_t time_div; /* Post-prescale divider */ 142}; 143 144static const struct bus_speed_cfg std_cfg_table[] = { 145 [BCM_SPD_100K] = {0x01, 0x01, 0x03, 0x06, 0x00, 0x02}, 146 [BCM_SPD_400K] = {0x05, 0x01, 0x03, 0x05, 0x01, 0x02}, 147 [BCM_SPD_1MHZ] = {0x01, 0x01, 0x03, 0x01, 0x01, 0x03}, 148}; 149 150static const struct hs_bus_speed_cfg hs_cfg_table[] = { 151 [BCM_SPD_3P4MHZ] = {0x01, 0x08, 0x14, 0x00, 0x06, 0x01, 0x00}, 152}; 153 154struct bcm_kona_i2c_dev { 155 struct device *device; 156 157 void __iomem *base; 158 int irq; 159 struct clk *external_clk; 160 161 struct i2c_adapter adapter; 162 163 struct completion done; 164 165 const struct bus_speed_cfg *std_cfg; 166 const struct hs_bus_speed_cfg *hs_cfg; 167}; 168 169static void bcm_kona_i2c_send_cmd_to_ctrl(struct bcm_kona_i2c_dev *dev, 170 enum bcm_kona_cmd_t cmd) 171{ 172 dev_dbg(dev->device, "%s, %d\n", __func__, cmd); 173 174 switch (cmd) { 175 case BCM_CMD_NOACTION: 176 writel((CS_CMD_CMD_NO_ACTION << CS_CMD_SHIFT) | 177 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), 178 dev->base + CS_OFFSET); 179 break; 180 181 case BCM_CMD_START: 182 writel((CS_ACK_CMD_GEN_START << CS_ACK_SHIFT) | 183 (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) | 184 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), 185 dev->base + CS_OFFSET); 186 break; 187 188 case BCM_CMD_RESTART: 189 writel((CS_ACK_CMD_GEN_RESTART << CS_ACK_SHIFT) | 190 (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) | 191 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), 192 dev->base + CS_OFFSET); 193 break; 194 195 case BCM_CMD_STOP: 196 writel((CS_CMD_CMD_STOP << CS_CMD_SHIFT) | 197 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), 198 dev->base + CS_OFFSET); 199 break; 200 201 default: 202 dev_err(dev->device, "Unknown command %d\n", cmd); 203 } 204} 205 206static void bcm_kona_i2c_enable_clock(struct bcm_kona_i2c_dev *dev) 207{ 208 writel(readl(dev->base + CLKEN_OFFSET) | CLKEN_CLKEN_MASK, 209 dev->base + CLKEN_OFFSET); 210} 211 212static void bcm_kona_i2c_disable_clock(struct bcm_kona_i2c_dev *dev) 213{ 214 writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_CLKEN_MASK, 215 dev->base + CLKEN_OFFSET); 216} 217 218static irqreturn_t bcm_kona_i2c_isr(int irq, void *devid) 219{ 220 struct bcm_kona_i2c_dev *dev = devid; 221 uint32_t status = readl(dev->base + ISR_OFFSET); 222 223 if ((status & ~ISR_RESERVED_MASK) == 0) 224 return IRQ_NONE; 225 226 /* Must flush the TX FIFO when NAK detected */ 227 if (status & ISR_NOACK_MASK) 228 writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK, 229 dev->base + TXFCR_OFFSET); 230 231 writel(status & ~ISR_RESERVED_MASK, dev->base + ISR_OFFSET); 232 complete_all(&dev->done); 233 234 return IRQ_HANDLED; 235} 236 237/* Wait for ISR_CMDBUSY_MASK to go low before writing to CS, DAT, or RCD */ 238static int bcm_kona_i2c_wait_if_busy(struct bcm_kona_i2c_dev *dev) 239{ 240 unsigned long timeout = jiffies + msecs_to_jiffies(I2C_TIMEOUT); 241 242 while (readl(dev->base + ISR_OFFSET) & ISR_CMDBUSY_MASK) 243 if (time_after(jiffies, timeout)) { 244 dev_err(dev->device, "CMDBUSY timeout\n"); 245 return -ETIMEDOUT; 246 } 247 248 return 0; 249} 250 251/* Send command to I2C bus */ 252static int bcm_kona_send_i2c_cmd(struct bcm_kona_i2c_dev *dev, 253 enum bcm_kona_cmd_t cmd) 254{ 255 int rc; 256 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT); 257 258 /* Make sure the hardware is ready */ 259 rc = bcm_kona_i2c_wait_if_busy(dev); 260 if (rc < 0) 261 return rc; 262 263 /* Unmask the session done interrupt */ 264 writel(IER_I2C_INT_EN_MASK, dev->base + IER_OFFSET); 265 266 /* Mark as incomplete before sending the command */ 267 reinit_completion(&dev->done); 268 269 /* Send the command */ 270 bcm_kona_i2c_send_cmd_to_ctrl(dev, cmd); 271 272 /* Wait for transaction to finish or timeout */ 273 time_left = wait_for_completion_timeout(&dev->done, time_left); 274 275 /* Mask all interrupts */ 276 writel(0, dev->base + IER_OFFSET); 277 278 if (!time_left) { 279 dev_err(dev->device, "controller timed out\n"); 280 rc = -ETIMEDOUT; 281 } 282 283 /* Clear command */ 284 bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION); 285 286 return rc; 287} 288 289/* Read a single RX FIFO worth of data from the i2c bus */ 290static int bcm_kona_i2c_read_fifo_single(struct bcm_kona_i2c_dev *dev, 291 uint8_t *buf, unsigned int len, 292 unsigned int last_byte_nak) 293{ 294 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT); 295 296 /* Mark as incomplete before starting the RX FIFO */ 297 reinit_completion(&dev->done); 298 299 /* Unmask the read complete interrupt */ 300 writel(IER_READ_COMPLETE_INT_MASK, dev->base + IER_OFFSET); 301 302 /* Start the RX FIFO */ 303 writel((last_byte_nak << RXFCR_NACK_EN_SHIFT) | 304 (len << RXFCR_READ_COUNT_SHIFT), 305 dev->base + RXFCR_OFFSET); 306 307 /* Wait for FIFO read to complete */ 308 time_left = wait_for_completion_timeout(&dev->done, time_left); 309 310 /* Mask all interrupts */ 311 writel(0, dev->base + IER_OFFSET); 312 313 if (!time_left) { 314 dev_err(dev->device, "RX FIFO time out\n"); 315 return -EREMOTEIO; 316 } 317 318 /* Read data from FIFO */ 319 for (; len > 0; len--, buf++) 320 *buf = readl(dev->base + RXFIFORDOUT_OFFSET); 321 322 return 0; 323} 324 325/* Read any amount of data using the RX FIFO from the i2c bus */ 326static int bcm_kona_i2c_read_fifo(struct bcm_kona_i2c_dev *dev, 327 struct i2c_msg *msg) 328{ 329 unsigned int bytes_to_read = MAX_RX_FIFO_SIZE; 330 unsigned int last_byte_nak = 0; 331 unsigned int bytes_read = 0; 332 int rc; 333 334 uint8_t *tmp_buf = msg->buf; 335 336 while (bytes_read < msg->len) { 337 if (msg->len - bytes_read <= MAX_RX_FIFO_SIZE) { 338 last_byte_nak = 1; /* NAK last byte of transfer */ 339 bytes_to_read = msg->len - bytes_read; 340 } 341 342 rc = bcm_kona_i2c_read_fifo_single(dev, tmp_buf, bytes_to_read, 343 last_byte_nak); 344 if (rc < 0) 345 return -EREMOTEIO; 346 347 bytes_read += bytes_to_read; 348 tmp_buf += bytes_to_read; 349 } 350 351 return 0; 352} 353 354/* Write a single byte of data to the i2c bus */ 355static int bcm_kona_i2c_write_byte(struct bcm_kona_i2c_dev *dev, uint8_t data, 356 unsigned int nak_expected) 357{ 358 int rc; 359 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT); 360 unsigned int nak_received; 361 362 /* Make sure the hardware is ready */ 363 rc = bcm_kona_i2c_wait_if_busy(dev); 364 if (rc < 0) 365 return rc; 366 367 /* Clear pending session done interrupt */ 368 writel(ISR_SES_DONE_MASK, dev->base + ISR_OFFSET); 369 370 /* Unmask the session done interrupt */ 371 writel(IER_I2C_INT_EN_MASK, dev->base + IER_OFFSET); 372 373 /* Mark as incomplete before sending the data */ 374 reinit_completion(&dev->done); 375 376 /* Send one byte of data */ 377 writel(data, dev->base + DAT_OFFSET); 378 379 /* Wait for byte to be written */ 380 time_left = wait_for_completion_timeout(&dev->done, time_left); 381 382 /* Mask all interrupts */ 383 writel(0, dev->base + IER_OFFSET); 384 385 if (!time_left) { 386 dev_dbg(dev->device, "controller timed out\n"); 387 return -ETIMEDOUT; 388 } 389 390 nak_received = readl(dev->base + CS_OFFSET) & CS_ACK_MASK ? 1 : 0; 391 392 if (nak_received ^ nak_expected) { 393 dev_dbg(dev->device, "unexpected NAK/ACK\n"); 394 return -EREMOTEIO; 395 } 396 397 return 0; 398} 399 400/* Write a single TX FIFO worth of data to the i2c bus */ 401static int bcm_kona_i2c_write_fifo_single(struct bcm_kona_i2c_dev *dev, 402 uint8_t *buf, unsigned int len) 403{ 404 int k; 405 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT); 406 unsigned int fifo_status; 407 408 /* Mark as incomplete before sending data to the TX FIFO */ 409 reinit_completion(&dev->done); 410 411 /* Unmask the fifo empty and nak interrupt */ 412 writel(IER_FIFO_INT_EN_MASK | IER_NOACK_EN_MASK, 413 dev->base + IER_OFFSET); 414 415 /* Disable IRQ to load a FIFO worth of data without interruption */ 416 disable_irq(dev->irq); 417 418 /* Write data into FIFO */ 419 for (k = 0; k < len; k++) 420 writel(buf[k], (dev->base + DAT_OFFSET)); 421 422 /* Enable IRQ now that data has been loaded */ 423 enable_irq(dev->irq); 424 425 /* Wait for FIFO to empty */ 426 do { 427 time_left = wait_for_completion_timeout(&dev->done, time_left); 428 fifo_status = readl(dev->base + FIFO_STATUS_OFFSET); 429 } while (time_left && !(fifo_status & FIFO_STATUS_TXFIFO_EMPTY_MASK)); 430 431 /* Mask all interrupts */ 432 writel(0, dev->base + IER_OFFSET); 433 434 /* Check if there was a NAK */ 435 if (readl(dev->base + CS_OFFSET) & CS_ACK_MASK) { 436 dev_err(dev->device, "unexpected NAK\n"); 437 return -EREMOTEIO; 438 } 439 440 /* Check if a timeout occured */ 441 if (!time_left) { 442 dev_err(dev->device, "completion timed out\n"); 443 return -EREMOTEIO; 444 } 445 446 return 0; 447} 448 449 450/* Write any amount of data using TX FIFO to the i2c bus */ 451static int bcm_kona_i2c_write_fifo(struct bcm_kona_i2c_dev *dev, 452 struct i2c_msg *msg) 453{ 454 unsigned int bytes_to_write = MAX_TX_FIFO_SIZE; 455 unsigned int bytes_written = 0; 456 int rc; 457 458 uint8_t *tmp_buf = msg->buf; 459 460 while (bytes_written < msg->len) { 461 if (msg->len - bytes_written <= MAX_TX_FIFO_SIZE) 462 bytes_to_write = msg->len - bytes_written; 463 464 rc = bcm_kona_i2c_write_fifo_single(dev, tmp_buf, 465 bytes_to_write); 466 if (rc < 0) 467 return -EREMOTEIO; 468 469 bytes_written += bytes_to_write; 470 tmp_buf += bytes_to_write; 471 } 472 473 return 0; 474} 475 476/* Send i2c address */ 477static int bcm_kona_i2c_do_addr(struct bcm_kona_i2c_dev *dev, 478 struct i2c_msg *msg) 479{ 480 unsigned char addr; 481 482 if (msg->flags & I2C_M_TEN) { 483 /* First byte is 11110XX0 where XX is upper 2 bits */ 484 addr = 0xF0 | ((msg->addr & 0x300) >> 7); 485 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) 486 return -EREMOTEIO; 487 488 /* Second byte is the remaining 8 bits */ 489 addr = msg->addr & 0xFF; 490 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) 491 return -EREMOTEIO; 492 493 if (msg->flags & I2C_M_RD) { 494 /* For read, send restart command */ 495 if (bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART) < 0) 496 return -EREMOTEIO; 497 498 /* Then re-send the first byte with the read bit set */ 499 addr = 0xF0 | ((msg->addr & 0x300) >> 7) | 0x01; 500 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) 501 return -EREMOTEIO; 502 } 503 } else { 504 addr = msg->addr << 1; 505 506 if (msg->flags & I2C_M_RD) 507 addr |= 1; 508 509 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) 510 return -EREMOTEIO; 511 } 512 513 return 0; 514} 515 516static void bcm_kona_i2c_enable_autosense(struct bcm_kona_i2c_dev *dev) 517{ 518 writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_AUTOSENSE_OFF_MASK, 519 dev->base + CLKEN_OFFSET); 520} 521 522static void bcm_kona_i2c_config_timing(struct bcm_kona_i2c_dev *dev) 523{ 524 writel(readl(dev->base + HSTIM_OFFSET) & ~HSTIM_HS_MODE_MASK, 525 dev->base + HSTIM_OFFSET); 526 527 writel((dev->std_cfg->prescale << TIM_PRESCALE_SHIFT) | 528 (dev->std_cfg->time_p << TIM_P_SHIFT) | 529 (dev->std_cfg->no_div << TIM_NO_DIV_SHIFT) | 530 (dev->std_cfg->time_div << TIM_DIV_SHIFT), 531 dev->base + TIM_OFFSET); 532 533 writel((dev->std_cfg->time_m << CLKEN_M_SHIFT) | 534 (dev->std_cfg->time_n << CLKEN_N_SHIFT) | 535 CLKEN_CLKEN_MASK, 536 dev->base + CLKEN_OFFSET); 537} 538 539static void bcm_kona_i2c_config_timing_hs(struct bcm_kona_i2c_dev *dev) 540{ 541 writel((dev->hs_cfg->prescale << TIM_PRESCALE_SHIFT) | 542 (dev->hs_cfg->time_p << TIM_P_SHIFT) | 543 (dev->hs_cfg->no_div << TIM_NO_DIV_SHIFT) | 544 (dev->hs_cfg->time_div << TIM_DIV_SHIFT), 545 dev->base + TIM_OFFSET); 546 547 writel((dev->hs_cfg->hs_hold << HSTIM_HS_HOLD_SHIFT) | 548 (dev->hs_cfg->hs_high_phase << HSTIM_HS_HIGH_PHASE_SHIFT) | 549 (dev->hs_cfg->hs_setup << HSTIM_HS_SETUP_SHIFT), 550 dev->base + HSTIM_OFFSET); 551 552 writel(readl(dev->base + HSTIM_OFFSET) | HSTIM_HS_MODE_MASK, 553 dev->base + HSTIM_OFFSET); 554} 555 556static int bcm_kona_i2c_switch_to_hs(struct bcm_kona_i2c_dev *dev) 557{ 558 int rc; 559 560 /* Send mastercode at standard speed */ 561 rc = bcm_kona_i2c_write_byte(dev, MASTERCODE, 1); 562 if (rc < 0) { 563 pr_err("High speed handshake failed\n"); 564 return rc; 565 } 566 567 /* Configure external clock to higher frequency */ 568 rc = clk_set_rate(dev->external_clk, HS_EXT_CLK_FREQ); 569 if (rc) { 570 dev_err(dev->device, "%s: clk_set_rate returned %d\n", 571 __func__, rc); 572 return rc; 573 } 574 575 /* Reconfigure internal dividers */ 576 bcm_kona_i2c_config_timing_hs(dev); 577 578 /* Send a restart command */ 579 rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART); 580 if (rc < 0) 581 dev_err(dev->device, "High speed restart command failed\n"); 582 583 return rc; 584} 585 586static int bcm_kona_i2c_switch_to_std(struct bcm_kona_i2c_dev *dev) 587{ 588 int rc; 589 590 /* Reconfigure internal dividers */ 591 bcm_kona_i2c_config_timing(dev); 592 593 /* Configure external clock to lower frequency */ 594 rc = clk_set_rate(dev->external_clk, STD_EXT_CLK_FREQ); 595 if (rc) { 596 dev_err(dev->device, "%s: clk_set_rate returned %d\n", 597 __func__, rc); 598 } 599 600 return rc; 601} 602 603/* Master transfer function */ 604static int bcm_kona_i2c_xfer(struct i2c_adapter *adapter, 605 struct i2c_msg msgs[], int num) 606{ 607 struct bcm_kona_i2c_dev *dev = i2c_get_adapdata(adapter); 608 struct i2c_msg *pmsg; 609 int rc = 0; 610 int i; 611 612 rc = clk_prepare_enable(dev->external_clk); 613 if (rc) { 614 dev_err(dev->device, "%s: peri clock enable failed. err %d\n", 615 __func__, rc); 616 return rc; 617 } 618 619 /* Enable pad output */ 620 writel(0, dev->base + PADCTL_OFFSET); 621 622 /* Enable internal clocks */ 623 bcm_kona_i2c_enable_clock(dev); 624 625 /* Send start command */ 626 rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_START); 627 if (rc < 0) { 628 dev_err(dev->device, "Start command failed rc = %d\n", rc); 629 goto xfer_disable_pad; 630 } 631 632 /* Switch to high speed if applicable */ 633 if (dev->hs_cfg) { 634 rc = bcm_kona_i2c_switch_to_hs(dev); 635 if (rc < 0) 636 goto xfer_send_stop; 637 } 638 639 /* Loop through all messages */ 640 for (i = 0; i < num; i++) { 641 pmsg = &msgs[i]; 642 643 /* Send restart for subsequent messages */ 644 if ((i != 0) && ((pmsg->flags & I2C_M_NOSTART) == 0)) { 645 rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART); 646 if (rc < 0) { 647 dev_err(dev->device, 648 "restart cmd failed rc = %d\n", rc); 649 goto xfer_send_stop; 650 } 651 } 652 653 /* Send slave address */ 654 if (!(pmsg->flags & I2C_M_NOSTART)) { 655 rc = bcm_kona_i2c_do_addr(dev, pmsg); 656 if (rc < 0) { 657 dev_err(dev->device, 658 "NAK from addr %2.2x msg#%d rc = %d\n", 659 pmsg->addr, i, rc); 660 goto xfer_send_stop; 661 } 662 } 663 664 /* Perform data transfer */ 665 if (pmsg->flags & I2C_M_RD) { 666 rc = bcm_kona_i2c_read_fifo(dev, pmsg); 667 if (rc < 0) { 668 dev_err(dev->device, "read failure\n"); 669 goto xfer_send_stop; 670 } 671 } else { 672 rc = bcm_kona_i2c_write_fifo(dev, pmsg); 673 if (rc < 0) { 674 dev_err(dev->device, "write failure"); 675 goto xfer_send_stop; 676 } 677 } 678 } 679 680 rc = num; 681 682xfer_send_stop: 683 /* Send a STOP command */ 684 bcm_kona_send_i2c_cmd(dev, BCM_CMD_STOP); 685 686 /* Return from high speed if applicable */ 687 if (dev->hs_cfg) { 688 int hs_rc = bcm_kona_i2c_switch_to_std(dev); 689 690 if (hs_rc) 691 rc = hs_rc; 692 } 693 694xfer_disable_pad: 695 /* Disable pad output */ 696 writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET); 697 698 /* Stop internal clock */ 699 bcm_kona_i2c_disable_clock(dev); 700 701 clk_disable_unprepare(dev->external_clk); 702 703 return rc; 704} 705 706static uint32_t bcm_kona_i2c_functionality(struct i2c_adapter *adap) 707{ 708 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR | 709 I2C_FUNC_NOSTART; 710} 711 712static const struct i2c_algorithm bcm_algo = { 713 .master_xfer = bcm_kona_i2c_xfer, 714 .functionality = bcm_kona_i2c_functionality, 715}; 716 717static int bcm_kona_i2c_assign_bus_speed(struct bcm_kona_i2c_dev *dev) 718{ 719 unsigned int bus_speed; 720 int ret = of_property_read_u32(dev->device->of_node, "clock-frequency", 721 &bus_speed); 722 if (ret < 0) { 723 dev_err(dev->device, "missing clock-frequency property\n"); 724 return -ENODEV; 725 } 726 727 switch (bus_speed) { 728 case 100000: 729 dev->std_cfg = &std_cfg_table[BCM_SPD_100K]; 730 break; 731 case 400000: 732 dev->std_cfg = &std_cfg_table[BCM_SPD_400K]; 733 break; 734 case 1000000: 735 dev->std_cfg = &std_cfg_table[BCM_SPD_1MHZ]; 736 break; 737 case 3400000: 738 /* Send mastercode at 100k */ 739 dev->std_cfg = &std_cfg_table[BCM_SPD_100K]; 740 dev->hs_cfg = &hs_cfg_table[BCM_SPD_3P4MHZ]; 741 break; 742 default: 743 pr_err("%d hz bus speed not supported\n", bus_speed); 744 pr_err("Valid speeds are 100khz, 400khz, 1mhz, and 3.4mhz\n"); 745 return -EINVAL; 746 } 747 748 return 0; 749} 750 751static int bcm_kona_i2c_probe(struct platform_device *pdev) 752{ 753 int rc = 0; 754 struct bcm_kona_i2c_dev *dev; 755 struct i2c_adapter *adap; 756 struct resource *iomem; 757 758 /* Allocate memory for private data structure */ 759 dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL); 760 if (!dev) 761 return -ENOMEM; 762 763 platform_set_drvdata(pdev, dev); 764 dev->device = &pdev->dev; 765 init_completion(&dev->done); 766 767 /* Map hardware registers */ 768 iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 769 dev->base = devm_ioremap_resource(dev->device, iomem); 770 if (IS_ERR(dev->base)) 771 return -ENOMEM; 772 773 /* Get and enable external clock */ 774 dev->external_clk = devm_clk_get(dev->device, NULL); 775 if (IS_ERR(dev->external_clk)) { 776 dev_err(dev->device, "couldn't get clock\n"); 777 return -ENODEV; 778 } 779 780 rc = clk_set_rate(dev->external_clk, STD_EXT_CLK_FREQ); 781 if (rc) { 782 dev_err(dev->device, "%s: clk_set_rate returned %d\n", 783 __func__, rc); 784 return rc; 785 } 786 787 rc = clk_prepare_enable(dev->external_clk); 788 if (rc) { 789 dev_err(dev->device, "couldn't enable clock\n"); 790 return rc; 791 } 792 793 /* Parse bus speed */ 794 rc = bcm_kona_i2c_assign_bus_speed(dev); 795 if (rc) 796 goto probe_disable_clk; 797 798 /* Enable internal clocks */ 799 bcm_kona_i2c_enable_clock(dev); 800 801 /* Configure internal dividers */ 802 bcm_kona_i2c_config_timing(dev); 803 804 /* Disable timeout */ 805 writel(0, dev->base + TOUT_OFFSET); 806 807 /* Enable autosense */ 808 bcm_kona_i2c_enable_autosense(dev); 809 810 /* Enable TX FIFO */ 811 writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK, 812 dev->base + TXFCR_OFFSET); 813 814 /* Mask all interrupts */ 815 writel(0, dev->base + IER_OFFSET); 816 817 /* Clear all pending interrupts */ 818 writel(ISR_CMDBUSY_MASK | 819 ISR_READ_COMPLETE_MASK | 820 ISR_SES_DONE_MASK | 821 ISR_ERR_MASK | 822 ISR_TXFIFOEMPTY_MASK | 823 ISR_NOACK_MASK, 824 dev->base + ISR_OFFSET); 825 826 /* Get the interrupt number */ 827 dev->irq = platform_get_irq(pdev, 0); 828 if (dev->irq < 0) { 829 dev_err(dev->device, "no irq resource\n"); 830 rc = -ENODEV; 831 goto probe_disable_clk; 832 } 833 834 /* register the ISR handler */ 835 rc = devm_request_irq(&pdev->dev, dev->irq, bcm_kona_i2c_isr, 836 IRQF_SHARED, pdev->name, dev); 837 if (rc) { 838 dev_err(dev->device, "failed to request irq %i\n", dev->irq); 839 goto probe_disable_clk; 840 } 841 842 /* Enable the controller but leave it idle */ 843 bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION); 844 845 /* Disable pad output */ 846 writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET); 847 848 /* Disable internal clock */ 849 bcm_kona_i2c_disable_clock(dev); 850 851 /* Disable external clock */ 852 clk_disable_unprepare(dev->external_clk); 853 854 /* Add the i2c adapter */ 855 adap = &dev->adapter; 856 i2c_set_adapdata(adap, dev); 857 adap->owner = THIS_MODULE; 858 strlcpy(adap->name, "Broadcom I2C adapter", sizeof(adap->name)); 859 adap->algo = &bcm_algo; 860 adap->dev.parent = &pdev->dev; 861 adap->dev.of_node = pdev->dev.of_node; 862 863 rc = i2c_add_adapter(adap); 864 if (rc) { 865 dev_err(dev->device, "failed to add adapter\n"); 866 return rc; 867 } 868 869 dev_info(dev->device, "device registered successfully\n"); 870 871 return 0; 872 873probe_disable_clk: 874 bcm_kona_i2c_disable_clock(dev); 875 clk_disable_unprepare(dev->external_clk); 876 877 return rc; 878} 879 880static int bcm_kona_i2c_remove(struct platform_device *pdev) 881{ 882 struct bcm_kona_i2c_dev *dev = platform_get_drvdata(pdev); 883 884 i2c_del_adapter(&dev->adapter); 885 886 return 0; 887} 888 889static const struct of_device_id bcm_kona_i2c_of_match[] = { 890 {.compatible = "brcm,kona-i2c",}, 891 {}, 892}; 893MODULE_DEVICE_TABLE(of, bcm_kona_i2c_of_match); 894 895static struct platform_driver bcm_kona_i2c_driver = { 896 .driver = { 897 .name = "bcm-kona-i2c", 898 .owner = THIS_MODULE, 899 .of_match_table = bcm_kona_i2c_of_match, 900 }, 901 .probe = bcm_kona_i2c_probe, 902 .remove = bcm_kona_i2c_remove, 903}; 904module_platform_driver(bcm_kona_i2c_driver); 905 906MODULE_AUTHOR("Tim Kryger <tkryger@broadcom.com>"); 907MODULE_DESCRIPTION("Broadcom Kona I2C Driver"); 908MODULE_LICENSE("GPL v2"); 909