1/* Intel(R) Gigabit Ethernet Linux driver 2 * Copyright(c) 2007-2014 Intel Corporation. 3 * 4 * This program is free software; you can redistribute it and/or modify it 5 * under the terms and conditions of the GNU General Public License, 6 * version 2, as published by the Free Software Foundation. 7 * 8 * This program is distributed in the hope it will be useful, but WITHOUT 9 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 10 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 11 * more details. 12 * 13 * You should have received a copy of the GNU General Public License along with 14 * this program; if not, see <http://www.gnu.org/licenses/>. 15 * 16 * The full GNU General Public License is included in this distribution in 17 * the file called "COPYING". 18 * 19 * Contact Information: 20 * e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> 21 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 22 */ 23 24#include <linux/if_ether.h> 25#include <linux/delay.h> 26#include <linux/pci.h> 27#include <linux/netdevice.h> 28#include <linux/etherdevice.h> 29 30#include "e1000_mac.h" 31 32#include "igb.h" 33 34static s32 igb_set_default_fc(struct e1000_hw *hw); 35static s32 igb_set_fc_watermarks(struct e1000_hw *hw); 36 37/** 38 * igb_get_bus_info_pcie - Get PCIe bus information 39 * @hw: pointer to the HW structure 40 * 41 * Determines and stores the system bus information for a particular 42 * network interface. The following bus information is determined and stored: 43 * bus speed, bus width, type (PCIe), and PCIe function. 44 **/ 45s32 igb_get_bus_info_pcie(struct e1000_hw *hw) 46{ 47 struct e1000_bus_info *bus = &hw->bus; 48 s32 ret_val; 49 u32 reg; 50 u16 pcie_link_status; 51 52 bus->type = e1000_bus_type_pci_express; 53 54 ret_val = igb_read_pcie_cap_reg(hw, 55 PCI_EXP_LNKSTA, 56 &pcie_link_status); 57 if (ret_val) { 58 bus->width = e1000_bus_width_unknown; 59 bus->speed = e1000_bus_speed_unknown; 60 } else { 61 switch (pcie_link_status & PCI_EXP_LNKSTA_CLS) { 62 case PCI_EXP_LNKSTA_CLS_2_5GB: 63 bus->speed = e1000_bus_speed_2500; 64 break; 65 case PCI_EXP_LNKSTA_CLS_5_0GB: 66 bus->speed = e1000_bus_speed_5000; 67 break; 68 default: 69 bus->speed = e1000_bus_speed_unknown; 70 break; 71 } 72 73 bus->width = (enum e1000_bus_width)((pcie_link_status & 74 PCI_EXP_LNKSTA_NLW) >> 75 PCI_EXP_LNKSTA_NLW_SHIFT); 76 } 77 78 reg = rd32(E1000_STATUS); 79 bus->func = (reg & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT; 80 81 return 0; 82} 83 84/** 85 * igb_clear_vfta - Clear VLAN filter table 86 * @hw: pointer to the HW structure 87 * 88 * Clears the register array which contains the VLAN filter table by 89 * setting all the values to 0. 90 **/ 91void igb_clear_vfta(struct e1000_hw *hw) 92{ 93 u32 offset; 94 95 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { 96 array_wr32(E1000_VFTA, offset, 0); 97 wrfl(); 98 } 99} 100 101/** 102 * igb_write_vfta - Write value to VLAN filter table 103 * @hw: pointer to the HW structure 104 * @offset: register offset in VLAN filter table 105 * @value: register value written to VLAN filter table 106 * 107 * Writes value at the given offset in the register array which stores 108 * the VLAN filter table. 109 **/ 110static void igb_write_vfta(struct e1000_hw *hw, u32 offset, u32 value) 111{ 112 array_wr32(E1000_VFTA, offset, value); 113 wrfl(); 114} 115 116/* Due to a hw errata, if the host tries to configure the VFTA register 117 * while performing queries from the BMC or DMA, then the VFTA in some 118 * cases won't be written. 119 */ 120 121/** 122 * igb_clear_vfta_i350 - Clear VLAN filter table 123 * @hw: pointer to the HW structure 124 * 125 * Clears the register array which contains the VLAN filter table by 126 * setting all the values to 0. 127 **/ 128void igb_clear_vfta_i350(struct e1000_hw *hw) 129{ 130 u32 offset; 131 int i; 132 133 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { 134 for (i = 0; i < 10; i++) 135 array_wr32(E1000_VFTA, offset, 0); 136 137 wrfl(); 138 } 139} 140 141/** 142 * igb_write_vfta_i350 - Write value to VLAN filter table 143 * @hw: pointer to the HW structure 144 * @offset: register offset in VLAN filter table 145 * @value: register value written to VLAN filter table 146 * 147 * Writes value at the given offset in the register array which stores 148 * the VLAN filter table. 149 **/ 150static void igb_write_vfta_i350(struct e1000_hw *hw, u32 offset, u32 value) 151{ 152 int i; 153 154 for (i = 0; i < 10; i++) 155 array_wr32(E1000_VFTA, offset, value); 156 157 wrfl(); 158} 159 160/** 161 * igb_init_rx_addrs - Initialize receive address's 162 * @hw: pointer to the HW structure 163 * @rar_count: receive address registers 164 * 165 * Setups the receive address registers by setting the base receive address 166 * register to the devices MAC address and clearing all the other receive 167 * address registers to 0. 168 **/ 169void igb_init_rx_addrs(struct e1000_hw *hw, u16 rar_count) 170{ 171 u32 i; 172 u8 mac_addr[ETH_ALEN] = {0}; 173 174 /* Setup the receive address */ 175 hw_dbg("Programming MAC Address into RAR[0]\n"); 176 177 hw->mac.ops.rar_set(hw, hw->mac.addr, 0); 178 179 /* Zero out the other (rar_entry_count - 1) receive addresses */ 180 hw_dbg("Clearing RAR[1-%u]\n", rar_count-1); 181 for (i = 1; i < rar_count; i++) 182 hw->mac.ops.rar_set(hw, mac_addr, i); 183} 184 185/** 186 * igb_vfta_set - enable or disable vlan in VLAN filter table 187 * @hw: pointer to the HW structure 188 * @vid: VLAN id to add or remove 189 * @add: if true add filter, if false remove 190 * 191 * Sets or clears a bit in the VLAN filter table array based on VLAN id 192 * and if we are adding or removing the filter 193 **/ 194s32 igb_vfta_set(struct e1000_hw *hw, u32 vid, bool add) 195{ 196 u32 index = (vid >> E1000_VFTA_ENTRY_SHIFT) & E1000_VFTA_ENTRY_MASK; 197 u32 mask = 1 << (vid & E1000_VFTA_ENTRY_BIT_SHIFT_MASK); 198 u32 vfta; 199 struct igb_adapter *adapter = hw->back; 200 s32 ret_val = 0; 201 202 vfta = adapter->shadow_vfta[index]; 203 204 /* bit was set/cleared before we started */ 205 if ((!!(vfta & mask)) == add) { 206 ret_val = -E1000_ERR_CONFIG; 207 } else { 208 if (add) 209 vfta |= mask; 210 else 211 vfta &= ~mask; 212 } 213 if ((hw->mac.type == e1000_i350) || (hw->mac.type == e1000_i354)) 214 igb_write_vfta_i350(hw, index, vfta); 215 else 216 igb_write_vfta(hw, index, vfta); 217 adapter->shadow_vfta[index] = vfta; 218 219 return ret_val; 220} 221 222/** 223 * igb_check_alt_mac_addr - Check for alternate MAC addr 224 * @hw: pointer to the HW structure 225 * 226 * Checks the nvm for an alternate MAC address. An alternate MAC address 227 * can be setup by pre-boot software and must be treated like a permanent 228 * address and must override the actual permanent MAC address. If an 229 * alternate MAC address is found it is saved in the hw struct and 230 * programmed into RAR0 and the function returns success, otherwise the 231 * function returns an error. 232 **/ 233s32 igb_check_alt_mac_addr(struct e1000_hw *hw) 234{ 235 u32 i; 236 s32 ret_val = 0; 237 u16 offset, nvm_alt_mac_addr_offset, nvm_data; 238 u8 alt_mac_addr[ETH_ALEN]; 239 240 /* Alternate MAC address is handled by the option ROM for 82580 241 * and newer. SW support not required. 242 */ 243 if (hw->mac.type >= e1000_82580) 244 goto out; 245 246 ret_val = hw->nvm.ops.read(hw, NVM_ALT_MAC_ADDR_PTR, 1, 247 &nvm_alt_mac_addr_offset); 248 if (ret_val) { 249 hw_dbg("NVM Read Error\n"); 250 goto out; 251 } 252 253 if ((nvm_alt_mac_addr_offset == 0xFFFF) || 254 (nvm_alt_mac_addr_offset == 0x0000)) 255 /* There is no Alternate MAC Address */ 256 goto out; 257 258 if (hw->bus.func == E1000_FUNC_1) 259 nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN1; 260 if (hw->bus.func == E1000_FUNC_2) 261 nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN2; 262 263 if (hw->bus.func == E1000_FUNC_3) 264 nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN3; 265 for (i = 0; i < ETH_ALEN; i += 2) { 266 offset = nvm_alt_mac_addr_offset + (i >> 1); 267 ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data); 268 if (ret_val) { 269 hw_dbg("NVM Read Error\n"); 270 goto out; 271 } 272 273 alt_mac_addr[i] = (u8)(nvm_data & 0xFF); 274 alt_mac_addr[i + 1] = (u8)(nvm_data >> 8); 275 } 276 277 /* if multicast bit is set, the alternate address will not be used */ 278 if (is_multicast_ether_addr(alt_mac_addr)) { 279 hw_dbg("Ignoring Alternate Mac Address with MC bit set\n"); 280 goto out; 281 } 282 283 /* We have a valid alternate MAC address, and we want to treat it the 284 * same as the normal permanent MAC address stored by the HW into the 285 * RAR. Do this by mapping this address into RAR0. 286 */ 287 hw->mac.ops.rar_set(hw, alt_mac_addr, 0); 288 289out: 290 return ret_val; 291} 292 293/** 294 * igb_rar_set - Set receive address register 295 * @hw: pointer to the HW structure 296 * @addr: pointer to the receive address 297 * @index: receive address array register 298 * 299 * Sets the receive address array register at index to the address passed 300 * in by addr. 301 **/ 302void igb_rar_set(struct e1000_hw *hw, u8 *addr, u32 index) 303{ 304 u32 rar_low, rar_high; 305 306 /* HW expects these in little endian so we reverse the byte order 307 * from network order (big endian) to little endian 308 */ 309 rar_low = ((u32) addr[0] | 310 ((u32) addr[1] << 8) | 311 ((u32) addr[2] << 16) | ((u32) addr[3] << 24)); 312 313 rar_high = ((u32) addr[4] | ((u32) addr[5] << 8)); 314 315 /* If MAC address zero, no need to set the AV bit */ 316 if (rar_low || rar_high) 317 rar_high |= E1000_RAH_AV; 318 319 /* Some bridges will combine consecutive 32-bit writes into 320 * a single burst write, which will malfunction on some parts. 321 * The flushes avoid this. 322 */ 323 wr32(E1000_RAL(index), rar_low); 324 wrfl(); 325 wr32(E1000_RAH(index), rar_high); 326 wrfl(); 327} 328 329/** 330 * igb_mta_set - Set multicast filter table address 331 * @hw: pointer to the HW structure 332 * @hash_value: determines the MTA register and bit to set 333 * 334 * The multicast table address is a register array of 32-bit registers. 335 * The hash_value is used to determine what register the bit is in, the 336 * current value is read, the new bit is OR'd in and the new value is 337 * written back into the register. 338 **/ 339void igb_mta_set(struct e1000_hw *hw, u32 hash_value) 340{ 341 u32 hash_bit, hash_reg, mta; 342 343 /* The MTA is a register array of 32-bit registers. It is 344 * treated like an array of (32*mta_reg_count) bits. We want to 345 * set bit BitArray[hash_value]. So we figure out what register 346 * the bit is in, read it, OR in the new bit, then write 347 * back the new value. The (hw->mac.mta_reg_count - 1) serves as a 348 * mask to bits 31:5 of the hash value which gives us the 349 * register we're modifying. The hash bit within that register 350 * is determined by the lower 5 bits of the hash value. 351 */ 352 hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); 353 hash_bit = hash_value & 0x1F; 354 355 mta = array_rd32(E1000_MTA, hash_reg); 356 357 mta |= (1 << hash_bit); 358 359 array_wr32(E1000_MTA, hash_reg, mta); 360 wrfl(); 361} 362 363/** 364 * igb_hash_mc_addr - Generate a multicast hash value 365 * @hw: pointer to the HW structure 366 * @mc_addr: pointer to a multicast address 367 * 368 * Generates a multicast address hash value which is used to determine 369 * the multicast filter table array address and new table value. See 370 * igb_mta_set() 371 **/ 372static u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr) 373{ 374 u32 hash_value, hash_mask; 375 u8 bit_shift = 0; 376 377 /* Register count multiplied by bits per register */ 378 hash_mask = (hw->mac.mta_reg_count * 32) - 1; 379 380 /* For a mc_filter_type of 0, bit_shift is the number of left-shifts 381 * where 0xFF would still fall within the hash mask. 382 */ 383 while (hash_mask >> bit_shift != 0xFF) 384 bit_shift++; 385 386 /* The portion of the address that is used for the hash table 387 * is determined by the mc_filter_type setting. 388 * The algorithm is such that there is a total of 8 bits of shifting. 389 * The bit_shift for a mc_filter_type of 0 represents the number of 390 * left-shifts where the MSB of mc_addr[5] would still fall within 391 * the hash_mask. Case 0 does this exactly. Since there are a total 392 * of 8 bits of shifting, then mc_addr[4] will shift right the 393 * remaining number of bits. Thus 8 - bit_shift. The rest of the 394 * cases are a variation of this algorithm...essentially raising the 395 * number of bits to shift mc_addr[5] left, while still keeping the 396 * 8-bit shifting total. 397 * 398 * For example, given the following Destination MAC Address and an 399 * mta register count of 128 (thus a 4096-bit vector and 0xFFF mask), 400 * we can see that the bit_shift for case 0 is 4. These are the hash 401 * values resulting from each mc_filter_type... 402 * [0] [1] [2] [3] [4] [5] 403 * 01 AA 00 12 34 56 404 * LSB MSB 405 * 406 * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563 407 * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6 408 * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163 409 * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634 410 */ 411 switch (hw->mac.mc_filter_type) { 412 default: 413 case 0: 414 break; 415 case 1: 416 bit_shift += 1; 417 break; 418 case 2: 419 bit_shift += 2; 420 break; 421 case 3: 422 bit_shift += 4; 423 break; 424 } 425 426 hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) | 427 (((u16) mc_addr[5]) << bit_shift))); 428 429 return hash_value; 430} 431 432/** 433 * igb_update_mc_addr_list - Update Multicast addresses 434 * @hw: pointer to the HW structure 435 * @mc_addr_list: array of multicast addresses to program 436 * @mc_addr_count: number of multicast addresses to program 437 * 438 * Updates entire Multicast Table Array. 439 * The caller must have a packed mc_addr_list of multicast addresses. 440 **/ 441void igb_update_mc_addr_list(struct e1000_hw *hw, 442 u8 *mc_addr_list, u32 mc_addr_count) 443{ 444 u32 hash_value, hash_bit, hash_reg; 445 int i; 446 447 /* clear mta_shadow */ 448 memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); 449 450 /* update mta_shadow from mc_addr_list */ 451 for (i = 0; (u32) i < mc_addr_count; i++) { 452 hash_value = igb_hash_mc_addr(hw, mc_addr_list); 453 454 hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); 455 hash_bit = hash_value & 0x1F; 456 457 hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit); 458 mc_addr_list += (ETH_ALEN); 459 } 460 461 /* replace the entire MTA table */ 462 for (i = hw->mac.mta_reg_count - 1; i >= 0; i--) 463 array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]); 464 wrfl(); 465} 466 467/** 468 * igb_clear_hw_cntrs_base - Clear base hardware counters 469 * @hw: pointer to the HW structure 470 * 471 * Clears the base hardware counters by reading the counter registers. 472 **/ 473void igb_clear_hw_cntrs_base(struct e1000_hw *hw) 474{ 475 rd32(E1000_CRCERRS); 476 rd32(E1000_SYMERRS); 477 rd32(E1000_MPC); 478 rd32(E1000_SCC); 479 rd32(E1000_ECOL); 480 rd32(E1000_MCC); 481 rd32(E1000_LATECOL); 482 rd32(E1000_COLC); 483 rd32(E1000_DC); 484 rd32(E1000_SEC); 485 rd32(E1000_RLEC); 486 rd32(E1000_XONRXC); 487 rd32(E1000_XONTXC); 488 rd32(E1000_XOFFRXC); 489 rd32(E1000_XOFFTXC); 490 rd32(E1000_FCRUC); 491 rd32(E1000_GPRC); 492 rd32(E1000_BPRC); 493 rd32(E1000_MPRC); 494 rd32(E1000_GPTC); 495 rd32(E1000_GORCL); 496 rd32(E1000_GORCH); 497 rd32(E1000_GOTCL); 498 rd32(E1000_GOTCH); 499 rd32(E1000_RNBC); 500 rd32(E1000_RUC); 501 rd32(E1000_RFC); 502 rd32(E1000_ROC); 503 rd32(E1000_RJC); 504 rd32(E1000_TORL); 505 rd32(E1000_TORH); 506 rd32(E1000_TOTL); 507 rd32(E1000_TOTH); 508 rd32(E1000_TPR); 509 rd32(E1000_TPT); 510 rd32(E1000_MPTC); 511 rd32(E1000_BPTC); 512} 513 514/** 515 * igb_check_for_copper_link - Check for link (Copper) 516 * @hw: pointer to the HW structure 517 * 518 * Checks to see of the link status of the hardware has changed. If a 519 * change in link status has been detected, then we read the PHY registers 520 * to get the current speed/duplex if link exists. 521 **/ 522s32 igb_check_for_copper_link(struct e1000_hw *hw) 523{ 524 struct e1000_mac_info *mac = &hw->mac; 525 s32 ret_val; 526 bool link; 527 528 /* We only want to go out to the PHY registers to see if Auto-Neg 529 * has completed and/or if our link status has changed. The 530 * get_link_status flag is set upon receiving a Link Status 531 * Change or Rx Sequence Error interrupt. 532 */ 533 if (!mac->get_link_status) { 534 ret_val = 0; 535 goto out; 536 } 537 538 /* First we want to see if the MII Status Register reports 539 * link. If so, then we want to get the current speed/duplex 540 * of the PHY. 541 */ 542 ret_val = igb_phy_has_link(hw, 1, 0, &link); 543 if (ret_val) 544 goto out; 545 546 if (!link) 547 goto out; /* No link detected */ 548 549 mac->get_link_status = false; 550 551 /* Check if there was DownShift, must be checked 552 * immediately after link-up 553 */ 554 igb_check_downshift(hw); 555 556 /* If we are forcing speed/duplex, then we simply return since 557 * we have already determined whether we have link or not. 558 */ 559 if (!mac->autoneg) { 560 ret_val = -E1000_ERR_CONFIG; 561 goto out; 562 } 563 564 /* Auto-Neg is enabled. Auto Speed Detection takes care 565 * of MAC speed/duplex configuration. So we only need to 566 * configure Collision Distance in the MAC. 567 */ 568 igb_config_collision_dist(hw); 569 570 /* Configure Flow Control now that Auto-Neg has completed. 571 * First, we need to restore the desired flow control 572 * settings because we may have had to re-autoneg with a 573 * different link partner. 574 */ 575 ret_val = igb_config_fc_after_link_up(hw); 576 if (ret_val) 577 hw_dbg("Error configuring flow control\n"); 578 579out: 580 return ret_val; 581} 582 583/** 584 * igb_setup_link - Setup flow control and link settings 585 * @hw: pointer to the HW structure 586 * 587 * Determines which flow control settings to use, then configures flow 588 * control. Calls the appropriate media-specific link configuration 589 * function. Assuming the adapter has a valid link partner, a valid link 590 * should be established. Assumes the hardware has previously been reset 591 * and the transmitter and receiver are not enabled. 592 **/ 593s32 igb_setup_link(struct e1000_hw *hw) 594{ 595 s32 ret_val = 0; 596 597 /* In the case of the phy reset being blocked, we already have a link. 598 * We do not need to set it up again. 599 */ 600 if (igb_check_reset_block(hw)) 601 goto out; 602 603 /* If requested flow control is set to default, set flow control 604 * based on the EEPROM flow control settings. 605 */ 606 if (hw->fc.requested_mode == e1000_fc_default) { 607 ret_val = igb_set_default_fc(hw); 608 if (ret_val) 609 goto out; 610 } 611 612 /* We want to save off the original Flow Control configuration just 613 * in case we get disconnected and then reconnected into a different 614 * hub or switch with different Flow Control capabilities. 615 */ 616 hw->fc.current_mode = hw->fc.requested_mode; 617 618 hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.current_mode); 619 620 /* Call the necessary media_type subroutine to configure the link. */ 621 ret_val = hw->mac.ops.setup_physical_interface(hw); 622 if (ret_val) 623 goto out; 624 625 /* Initialize the flow control address, type, and PAUSE timer 626 * registers to their default values. This is done even if flow 627 * control is disabled, because it does not hurt anything to 628 * initialize these registers. 629 */ 630 hw_dbg("Initializing the Flow Control address, type and timer regs\n"); 631 wr32(E1000_FCT, FLOW_CONTROL_TYPE); 632 wr32(E1000_FCAH, FLOW_CONTROL_ADDRESS_HIGH); 633 wr32(E1000_FCAL, FLOW_CONTROL_ADDRESS_LOW); 634 635 wr32(E1000_FCTTV, hw->fc.pause_time); 636 637 ret_val = igb_set_fc_watermarks(hw); 638 639out: 640 641 return ret_val; 642} 643 644/** 645 * igb_config_collision_dist - Configure collision distance 646 * @hw: pointer to the HW structure 647 * 648 * Configures the collision distance to the default value and is used 649 * during link setup. Currently no func pointer exists and all 650 * implementations are handled in the generic version of this function. 651 **/ 652void igb_config_collision_dist(struct e1000_hw *hw) 653{ 654 u32 tctl; 655 656 tctl = rd32(E1000_TCTL); 657 658 tctl &= ~E1000_TCTL_COLD; 659 tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT; 660 661 wr32(E1000_TCTL, tctl); 662 wrfl(); 663} 664 665/** 666 * igb_set_fc_watermarks - Set flow control high/low watermarks 667 * @hw: pointer to the HW structure 668 * 669 * Sets the flow control high/low threshold (watermark) registers. If 670 * flow control XON frame transmission is enabled, then set XON frame 671 * tansmission as well. 672 **/ 673static s32 igb_set_fc_watermarks(struct e1000_hw *hw) 674{ 675 s32 ret_val = 0; 676 u32 fcrtl = 0, fcrth = 0; 677 678 /* Set the flow control receive threshold registers. Normally, 679 * these registers will be set to a default threshold that may be 680 * adjusted later by the driver's runtime code. However, if the 681 * ability to transmit pause frames is not enabled, then these 682 * registers will be set to 0. 683 */ 684 if (hw->fc.current_mode & e1000_fc_tx_pause) { 685 /* We need to set up the Receive Threshold high and low water 686 * marks as well as (optionally) enabling the transmission of 687 * XON frames. 688 */ 689 fcrtl = hw->fc.low_water; 690 if (hw->fc.send_xon) 691 fcrtl |= E1000_FCRTL_XONE; 692 693 fcrth = hw->fc.high_water; 694 } 695 wr32(E1000_FCRTL, fcrtl); 696 wr32(E1000_FCRTH, fcrth); 697 698 return ret_val; 699} 700 701/** 702 * igb_set_default_fc - Set flow control default values 703 * @hw: pointer to the HW structure 704 * 705 * Read the EEPROM for the default values for flow control and store the 706 * values. 707 **/ 708static s32 igb_set_default_fc(struct e1000_hw *hw) 709{ 710 s32 ret_val = 0; 711 u16 lan_offset; 712 u16 nvm_data; 713 714 /* Read and store word 0x0F of the EEPROM. This word contains bits 715 * that determine the hardware's default PAUSE (flow control) mode, 716 * a bit that determines whether the HW defaults to enabling or 717 * disabling auto-negotiation, and the direction of the 718 * SW defined pins. If there is no SW over-ride of the flow 719 * control setting, then the variable hw->fc will 720 * be initialized based on a value in the EEPROM. 721 */ 722 if (hw->mac.type == e1000_i350) { 723 lan_offset = NVM_82580_LAN_FUNC_OFFSET(hw->bus.func); 724 ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG 725 + lan_offset, 1, &nvm_data); 726 } else { 727 ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG, 728 1, &nvm_data); 729 } 730 731 if (ret_val) { 732 hw_dbg("NVM Read Error\n"); 733 goto out; 734 } 735 736 if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0) 737 hw->fc.requested_mode = e1000_fc_none; 738 else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 739 NVM_WORD0F_ASM_DIR) 740 hw->fc.requested_mode = e1000_fc_tx_pause; 741 else 742 hw->fc.requested_mode = e1000_fc_full; 743 744out: 745 return ret_val; 746} 747 748/** 749 * igb_force_mac_fc - Force the MAC's flow control settings 750 * @hw: pointer to the HW structure 751 * 752 * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the 753 * device control register to reflect the adapter settings. TFCE and RFCE 754 * need to be explicitly set by software when a copper PHY is used because 755 * autonegotiation is managed by the PHY rather than the MAC. Software must 756 * also configure these bits when link is forced on a fiber connection. 757 **/ 758s32 igb_force_mac_fc(struct e1000_hw *hw) 759{ 760 u32 ctrl; 761 s32 ret_val = 0; 762 763 ctrl = rd32(E1000_CTRL); 764 765 /* Because we didn't get link via the internal auto-negotiation 766 * mechanism (we either forced link or we got link via PHY 767 * auto-neg), we have to manually enable/disable transmit an 768 * receive flow control. 769 * 770 * The "Case" statement below enables/disable flow control 771 * according to the "hw->fc.current_mode" parameter. 772 * 773 * The possible values of the "fc" parameter are: 774 * 0: Flow control is completely disabled 775 * 1: Rx flow control is enabled (we can receive pause 776 * frames but not send pause frames). 777 * 2: Tx flow control is enabled (we can send pause frames 778 * frames but we do not receive pause frames). 779 * 3: Both Rx and TX flow control (symmetric) is enabled. 780 * other: No other values should be possible at this point. 781 */ 782 hw_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode); 783 784 switch (hw->fc.current_mode) { 785 case e1000_fc_none: 786 ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); 787 break; 788 case e1000_fc_rx_pause: 789 ctrl &= (~E1000_CTRL_TFCE); 790 ctrl |= E1000_CTRL_RFCE; 791 break; 792 case e1000_fc_tx_pause: 793 ctrl &= (~E1000_CTRL_RFCE); 794 ctrl |= E1000_CTRL_TFCE; 795 break; 796 case e1000_fc_full: 797 ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); 798 break; 799 default: 800 hw_dbg("Flow control param set incorrectly\n"); 801 ret_val = -E1000_ERR_CONFIG; 802 goto out; 803 } 804 805 wr32(E1000_CTRL, ctrl); 806 807out: 808 return ret_val; 809} 810 811/** 812 * igb_config_fc_after_link_up - Configures flow control after link 813 * @hw: pointer to the HW structure 814 * 815 * Checks the status of auto-negotiation after link up to ensure that the 816 * speed and duplex were not forced. If the link needed to be forced, then 817 * flow control needs to be forced also. If auto-negotiation is enabled 818 * and did not fail, then we configure flow control based on our link 819 * partner. 820 **/ 821s32 igb_config_fc_after_link_up(struct e1000_hw *hw) 822{ 823 struct e1000_mac_info *mac = &hw->mac; 824 s32 ret_val = 0; 825 u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg; 826 u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; 827 u16 speed, duplex; 828 829 /* Check for the case where we have fiber media and auto-neg failed 830 * so we had to force link. In this case, we need to force the 831 * configuration of the MAC to match the "fc" parameter. 832 */ 833 if (mac->autoneg_failed) { 834 if (hw->phy.media_type == e1000_media_type_internal_serdes) 835 ret_val = igb_force_mac_fc(hw); 836 } else { 837 if (hw->phy.media_type == e1000_media_type_copper) 838 ret_val = igb_force_mac_fc(hw); 839 } 840 841 if (ret_val) { 842 hw_dbg("Error forcing flow control settings\n"); 843 goto out; 844 } 845 846 /* Check for the case where we have copper media and auto-neg is 847 * enabled. In this case, we need to check and see if Auto-Neg 848 * has completed, and if so, how the PHY and link partner has 849 * flow control configured. 850 */ 851 if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) { 852 /* Read the MII Status Register and check to see if AutoNeg 853 * has completed. We read this twice because this reg has 854 * some "sticky" (latched) bits. 855 */ 856 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, 857 &mii_status_reg); 858 if (ret_val) 859 goto out; 860 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, 861 &mii_status_reg); 862 if (ret_val) 863 goto out; 864 865 if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) { 866 hw_dbg("Copper PHY and Auto Neg has not completed.\n"); 867 goto out; 868 } 869 870 /* The AutoNeg process has completed, so we now need to 871 * read both the Auto Negotiation Advertisement 872 * Register (Address 4) and the Auto_Negotiation Base 873 * Page Ability Register (Address 5) to determine how 874 * flow control was negotiated. 875 */ 876 ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV, 877 &mii_nway_adv_reg); 878 if (ret_val) 879 goto out; 880 ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY, 881 &mii_nway_lp_ability_reg); 882 if (ret_val) 883 goto out; 884 885 /* Two bits in the Auto Negotiation Advertisement Register 886 * (Address 4) and two bits in the Auto Negotiation Base 887 * Page Ability Register (Address 5) determine flow control 888 * for both the PHY and the link partner. The following 889 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, 890 * 1999, describes these PAUSE resolution bits and how flow 891 * control is determined based upon these settings. 892 * NOTE: DC = Don't Care 893 * 894 * LOCAL DEVICE | LINK PARTNER 895 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution 896 *-------|---------|-------|---------|-------------------- 897 * 0 | 0 | DC | DC | e1000_fc_none 898 * 0 | 1 | 0 | DC | e1000_fc_none 899 * 0 | 1 | 1 | 0 | e1000_fc_none 900 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 901 * 1 | 0 | 0 | DC | e1000_fc_none 902 * 1 | DC | 1 | DC | e1000_fc_full 903 * 1 | 1 | 0 | 0 | e1000_fc_none 904 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 905 * 906 * Are both PAUSE bits set to 1? If so, this implies 907 * Symmetric Flow Control is enabled at both ends. The 908 * ASM_DIR bits are irrelevant per the spec. 909 * 910 * For Symmetric Flow Control: 911 * 912 * LOCAL DEVICE | LINK PARTNER 913 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 914 *-------|---------|-------|---------|-------------------- 915 * 1 | DC | 1 | DC | E1000_fc_full 916 * 917 */ 918 if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 919 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { 920 /* Now we need to check if the user selected RX ONLY 921 * of pause frames. In this case, we had to advertise 922 * FULL flow control because we could not advertise RX 923 * ONLY. Hence, we must now check to see if we need to 924 * turn OFF the TRANSMISSION of PAUSE frames. 925 */ 926 if (hw->fc.requested_mode == e1000_fc_full) { 927 hw->fc.current_mode = e1000_fc_full; 928 hw_dbg("Flow Control = FULL.\n"); 929 } else { 930 hw->fc.current_mode = e1000_fc_rx_pause; 931 hw_dbg("Flow Control = RX PAUSE frames only.\n"); 932 } 933 } 934 /* For receiving PAUSE frames ONLY. 935 * 936 * LOCAL DEVICE | LINK PARTNER 937 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 938 *-------|---------|-------|---------|-------------------- 939 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 940 */ 941 else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && 942 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 943 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 944 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { 945 hw->fc.current_mode = e1000_fc_tx_pause; 946 hw_dbg("Flow Control = TX PAUSE frames only.\n"); 947 } 948 /* For transmitting PAUSE frames ONLY. 949 * 950 * LOCAL DEVICE | LINK PARTNER 951 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 952 *-------|---------|-------|---------|-------------------- 953 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 954 */ 955 else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 956 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 957 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 958 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { 959 hw->fc.current_mode = e1000_fc_rx_pause; 960 hw_dbg("Flow Control = RX PAUSE frames only.\n"); 961 } 962 /* Per the IEEE spec, at this point flow control should be 963 * disabled. However, we want to consider that we could 964 * be connected to a legacy switch that doesn't advertise 965 * desired flow control, but can be forced on the link 966 * partner. So if we advertised no flow control, that is 967 * what we will resolve to. If we advertised some kind of 968 * receive capability (Rx Pause Only or Full Flow Control) 969 * and the link partner advertised none, we will configure 970 * ourselves to enable Rx Flow Control only. We can do 971 * this safely for two reasons: If the link partner really 972 * didn't want flow control enabled, and we enable Rx, no 973 * harm done since we won't be receiving any PAUSE frames 974 * anyway. If the intent on the link partner was to have 975 * flow control enabled, then by us enabling RX only, we 976 * can at least receive pause frames and process them. 977 * This is a good idea because in most cases, since we are 978 * predominantly a server NIC, more times than not we will 979 * be asked to delay transmission of packets than asking 980 * our link partner to pause transmission of frames. 981 */ 982 else if ((hw->fc.requested_mode == e1000_fc_none) || 983 (hw->fc.requested_mode == e1000_fc_tx_pause) || 984 (hw->fc.strict_ieee)) { 985 hw->fc.current_mode = e1000_fc_none; 986 hw_dbg("Flow Control = NONE.\n"); 987 } else { 988 hw->fc.current_mode = e1000_fc_rx_pause; 989 hw_dbg("Flow Control = RX PAUSE frames only.\n"); 990 } 991 992 /* Now we need to do one last check... If we auto- 993 * negotiated to HALF DUPLEX, flow control should not be 994 * enabled per IEEE 802.3 spec. 995 */ 996 ret_val = hw->mac.ops.get_speed_and_duplex(hw, &speed, &duplex); 997 if (ret_val) { 998 hw_dbg("Error getting link speed and duplex\n"); 999 goto out; 1000 } 1001 1002 if (duplex == HALF_DUPLEX) 1003 hw->fc.current_mode = e1000_fc_none; 1004 1005 /* Now we call a subroutine to actually force the MAC 1006 * controller to use the correct flow control settings. 1007 */ 1008 ret_val = igb_force_mac_fc(hw); 1009 if (ret_val) { 1010 hw_dbg("Error forcing flow control settings\n"); 1011 goto out; 1012 } 1013 } 1014 /* Check for the case where we have SerDes media and auto-neg is 1015 * enabled. In this case, we need to check and see if Auto-Neg 1016 * has completed, and if so, how the PHY and link partner has 1017 * flow control configured. 1018 */ 1019 if ((hw->phy.media_type == e1000_media_type_internal_serdes) 1020 && mac->autoneg) { 1021 /* Read the PCS_LSTS and check to see if AutoNeg 1022 * has completed. 1023 */ 1024 pcs_status_reg = rd32(E1000_PCS_LSTAT); 1025 1026 if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) { 1027 hw_dbg("PCS Auto Neg has not completed.\n"); 1028 return ret_val; 1029 } 1030 1031 /* The AutoNeg process has completed, so we now need to 1032 * read both the Auto Negotiation Advertisement 1033 * Register (PCS_ANADV) and the Auto_Negotiation Base 1034 * Page Ability Register (PCS_LPAB) to determine how 1035 * flow control was negotiated. 1036 */ 1037 pcs_adv_reg = rd32(E1000_PCS_ANADV); 1038 pcs_lp_ability_reg = rd32(E1000_PCS_LPAB); 1039 1040 /* Two bits in the Auto Negotiation Advertisement Register 1041 * (PCS_ANADV) and two bits in the Auto Negotiation Base 1042 * Page Ability Register (PCS_LPAB) determine flow control 1043 * for both the PHY and the link partner. The following 1044 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, 1045 * 1999, describes these PAUSE resolution bits and how flow 1046 * control is determined based upon these settings. 1047 * NOTE: DC = Don't Care 1048 * 1049 * LOCAL DEVICE | LINK PARTNER 1050 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution 1051 *-------|---------|-------|---------|-------------------- 1052 * 0 | 0 | DC | DC | e1000_fc_none 1053 * 0 | 1 | 0 | DC | e1000_fc_none 1054 * 0 | 1 | 1 | 0 | e1000_fc_none 1055 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 1056 * 1 | 0 | 0 | DC | e1000_fc_none 1057 * 1 | DC | 1 | DC | e1000_fc_full 1058 * 1 | 1 | 0 | 0 | e1000_fc_none 1059 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 1060 * 1061 * Are both PAUSE bits set to 1? If so, this implies 1062 * Symmetric Flow Control is enabled at both ends. The 1063 * ASM_DIR bits are irrelevant per the spec. 1064 * 1065 * For Symmetric Flow Control: 1066 * 1067 * LOCAL DEVICE | LINK PARTNER 1068 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 1069 *-------|---------|-------|---------|-------------------- 1070 * 1 | DC | 1 | DC | e1000_fc_full 1071 * 1072 */ 1073 if ((pcs_adv_reg & E1000_TXCW_PAUSE) && 1074 (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) { 1075 /* Now we need to check if the user selected Rx ONLY 1076 * of pause frames. In this case, we had to advertise 1077 * FULL flow control because we could not advertise Rx 1078 * ONLY. Hence, we must now check to see if we need to 1079 * turn OFF the TRANSMISSION of PAUSE frames. 1080 */ 1081 if (hw->fc.requested_mode == e1000_fc_full) { 1082 hw->fc.current_mode = e1000_fc_full; 1083 hw_dbg("Flow Control = FULL.\n"); 1084 } else { 1085 hw->fc.current_mode = e1000_fc_rx_pause; 1086 hw_dbg("Flow Control = Rx PAUSE frames only.\n"); 1087 } 1088 } 1089 /* For receiving PAUSE frames ONLY. 1090 * 1091 * LOCAL DEVICE | LINK PARTNER 1092 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 1093 *-------|---------|-------|---------|-------------------- 1094 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 1095 */ 1096 else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) && 1097 (pcs_adv_reg & E1000_TXCW_ASM_DIR) && 1098 (pcs_lp_ability_reg & E1000_TXCW_PAUSE) && 1099 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { 1100 hw->fc.current_mode = e1000_fc_tx_pause; 1101 hw_dbg("Flow Control = Tx PAUSE frames only.\n"); 1102 } 1103 /* For transmitting PAUSE frames ONLY. 1104 * 1105 * LOCAL DEVICE | LINK PARTNER 1106 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 1107 *-------|---------|-------|---------|-------------------- 1108 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 1109 */ 1110 else if ((pcs_adv_reg & E1000_TXCW_PAUSE) && 1111 (pcs_adv_reg & E1000_TXCW_ASM_DIR) && 1112 !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) && 1113 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { 1114 hw->fc.current_mode = e1000_fc_rx_pause; 1115 hw_dbg("Flow Control = Rx PAUSE frames only.\n"); 1116 } else { 1117 /* Per the IEEE spec, at this point flow control 1118 * should be disabled. 1119 */ 1120 hw->fc.current_mode = e1000_fc_none; 1121 hw_dbg("Flow Control = NONE.\n"); 1122 } 1123 1124 /* Now we call a subroutine to actually force the MAC 1125 * controller to use the correct flow control settings. 1126 */ 1127 pcs_ctrl_reg = rd32(E1000_PCS_LCTL); 1128 pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL; 1129 wr32(E1000_PCS_LCTL, pcs_ctrl_reg); 1130 1131 ret_val = igb_force_mac_fc(hw); 1132 if (ret_val) { 1133 hw_dbg("Error forcing flow control settings\n"); 1134 return ret_val; 1135 } 1136 } 1137 1138out: 1139 return ret_val; 1140} 1141 1142/** 1143 * igb_get_speed_and_duplex_copper - Retrieve current speed/duplex 1144 * @hw: pointer to the HW structure 1145 * @speed: stores the current speed 1146 * @duplex: stores the current duplex 1147 * 1148 * Read the status register for the current speed/duplex and store the current 1149 * speed and duplex for copper connections. 1150 **/ 1151s32 igb_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, 1152 u16 *duplex) 1153{ 1154 u32 status; 1155 1156 status = rd32(E1000_STATUS); 1157 if (status & E1000_STATUS_SPEED_1000) { 1158 *speed = SPEED_1000; 1159 hw_dbg("1000 Mbs, "); 1160 } else if (status & E1000_STATUS_SPEED_100) { 1161 *speed = SPEED_100; 1162 hw_dbg("100 Mbs, "); 1163 } else { 1164 *speed = SPEED_10; 1165 hw_dbg("10 Mbs, "); 1166 } 1167 1168 if (status & E1000_STATUS_FD) { 1169 *duplex = FULL_DUPLEX; 1170 hw_dbg("Full Duplex\n"); 1171 } else { 1172 *duplex = HALF_DUPLEX; 1173 hw_dbg("Half Duplex\n"); 1174 } 1175 1176 return 0; 1177} 1178 1179/** 1180 * igb_get_hw_semaphore - Acquire hardware semaphore 1181 * @hw: pointer to the HW structure 1182 * 1183 * Acquire the HW semaphore to access the PHY or NVM 1184 **/ 1185s32 igb_get_hw_semaphore(struct e1000_hw *hw) 1186{ 1187 u32 swsm; 1188 s32 ret_val = 0; 1189 s32 timeout = hw->nvm.word_size + 1; 1190 s32 i = 0; 1191 1192 /* Get the SW semaphore */ 1193 while (i < timeout) { 1194 swsm = rd32(E1000_SWSM); 1195 if (!(swsm & E1000_SWSM_SMBI)) 1196 break; 1197 1198 udelay(50); 1199 i++; 1200 } 1201 1202 if (i == timeout) { 1203 hw_dbg("Driver can't access device - SMBI bit is set.\n"); 1204 ret_val = -E1000_ERR_NVM; 1205 goto out; 1206 } 1207 1208 /* Get the FW semaphore. */ 1209 for (i = 0; i < timeout; i++) { 1210 swsm = rd32(E1000_SWSM); 1211 wr32(E1000_SWSM, swsm | E1000_SWSM_SWESMBI); 1212 1213 /* Semaphore acquired if bit latched */ 1214 if (rd32(E1000_SWSM) & E1000_SWSM_SWESMBI) 1215 break; 1216 1217 udelay(50); 1218 } 1219 1220 if (i == timeout) { 1221 /* Release semaphores */ 1222 igb_put_hw_semaphore(hw); 1223 hw_dbg("Driver can't access the NVM\n"); 1224 ret_val = -E1000_ERR_NVM; 1225 goto out; 1226 } 1227 1228out: 1229 return ret_val; 1230} 1231 1232/** 1233 * igb_put_hw_semaphore - Release hardware semaphore 1234 * @hw: pointer to the HW structure 1235 * 1236 * Release hardware semaphore used to access the PHY or NVM 1237 **/ 1238void igb_put_hw_semaphore(struct e1000_hw *hw) 1239{ 1240 u32 swsm; 1241 1242 swsm = rd32(E1000_SWSM); 1243 1244 swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); 1245 1246 wr32(E1000_SWSM, swsm); 1247} 1248 1249/** 1250 * igb_get_auto_rd_done - Check for auto read completion 1251 * @hw: pointer to the HW structure 1252 * 1253 * Check EEPROM for Auto Read done bit. 1254 **/ 1255s32 igb_get_auto_rd_done(struct e1000_hw *hw) 1256{ 1257 s32 i = 0; 1258 s32 ret_val = 0; 1259 1260 1261 while (i < AUTO_READ_DONE_TIMEOUT) { 1262 if (rd32(E1000_EECD) & E1000_EECD_AUTO_RD) 1263 break; 1264 usleep_range(1000, 2000); 1265 i++; 1266 } 1267 1268 if (i == AUTO_READ_DONE_TIMEOUT) { 1269 hw_dbg("Auto read by HW from NVM has not completed.\n"); 1270 ret_val = -E1000_ERR_RESET; 1271 goto out; 1272 } 1273 1274out: 1275 return ret_val; 1276} 1277 1278/** 1279 * igb_valid_led_default - Verify a valid default LED config 1280 * @hw: pointer to the HW structure 1281 * @data: pointer to the NVM (EEPROM) 1282 * 1283 * Read the EEPROM for the current default LED configuration. If the 1284 * LED configuration is not valid, set to a valid LED configuration. 1285 **/ 1286static s32 igb_valid_led_default(struct e1000_hw *hw, u16 *data) 1287{ 1288 s32 ret_val; 1289 1290 ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); 1291 if (ret_val) { 1292 hw_dbg("NVM Read Error\n"); 1293 goto out; 1294 } 1295 1296 if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) { 1297 switch (hw->phy.media_type) { 1298 case e1000_media_type_internal_serdes: 1299 *data = ID_LED_DEFAULT_82575_SERDES; 1300 break; 1301 case e1000_media_type_copper: 1302 default: 1303 *data = ID_LED_DEFAULT; 1304 break; 1305 } 1306 } 1307out: 1308 return ret_val; 1309} 1310 1311/** 1312 * igb_id_led_init - 1313 * @hw: pointer to the HW structure 1314 * 1315 **/ 1316s32 igb_id_led_init(struct e1000_hw *hw) 1317{ 1318 struct e1000_mac_info *mac = &hw->mac; 1319 s32 ret_val; 1320 const u32 ledctl_mask = 0x000000FF; 1321 const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON; 1322 const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF; 1323 u16 data, i, temp; 1324 const u16 led_mask = 0x0F; 1325 1326 /* i210 and i211 devices have different LED mechanism */ 1327 if ((hw->mac.type == e1000_i210) || 1328 (hw->mac.type == e1000_i211)) 1329 ret_val = igb_valid_led_default_i210(hw, &data); 1330 else 1331 ret_val = igb_valid_led_default(hw, &data); 1332 1333 if (ret_val) 1334 goto out; 1335 1336 mac->ledctl_default = rd32(E1000_LEDCTL); 1337 mac->ledctl_mode1 = mac->ledctl_default; 1338 mac->ledctl_mode2 = mac->ledctl_default; 1339 1340 for (i = 0; i < 4; i++) { 1341 temp = (data >> (i << 2)) & led_mask; 1342 switch (temp) { 1343 case ID_LED_ON1_DEF2: 1344 case ID_LED_ON1_ON2: 1345 case ID_LED_ON1_OFF2: 1346 mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); 1347 mac->ledctl_mode1 |= ledctl_on << (i << 3); 1348 break; 1349 case ID_LED_OFF1_DEF2: 1350 case ID_LED_OFF1_ON2: 1351 case ID_LED_OFF1_OFF2: 1352 mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); 1353 mac->ledctl_mode1 |= ledctl_off << (i << 3); 1354 break; 1355 default: 1356 /* Do nothing */ 1357 break; 1358 } 1359 switch (temp) { 1360 case ID_LED_DEF1_ON2: 1361 case ID_LED_ON1_ON2: 1362 case ID_LED_OFF1_ON2: 1363 mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); 1364 mac->ledctl_mode2 |= ledctl_on << (i << 3); 1365 break; 1366 case ID_LED_DEF1_OFF2: 1367 case ID_LED_ON1_OFF2: 1368 case ID_LED_OFF1_OFF2: 1369 mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); 1370 mac->ledctl_mode2 |= ledctl_off << (i << 3); 1371 break; 1372 default: 1373 /* Do nothing */ 1374 break; 1375 } 1376 } 1377 1378out: 1379 return ret_val; 1380} 1381 1382/** 1383 * igb_cleanup_led - Set LED config to default operation 1384 * @hw: pointer to the HW structure 1385 * 1386 * Remove the current LED configuration and set the LED configuration 1387 * to the default value, saved from the EEPROM. 1388 **/ 1389s32 igb_cleanup_led(struct e1000_hw *hw) 1390{ 1391 wr32(E1000_LEDCTL, hw->mac.ledctl_default); 1392 return 0; 1393} 1394 1395/** 1396 * igb_blink_led - Blink LED 1397 * @hw: pointer to the HW structure 1398 * 1399 * Blink the led's which are set to be on. 1400 **/ 1401s32 igb_blink_led(struct e1000_hw *hw) 1402{ 1403 u32 ledctl_blink = 0; 1404 u32 i; 1405 1406 if (hw->phy.media_type == e1000_media_type_fiber) { 1407 /* always blink LED0 for PCI-E fiber */ 1408 ledctl_blink = E1000_LEDCTL_LED0_BLINK | 1409 (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT); 1410 } else { 1411 /* Set the blink bit for each LED that's "on" (0x0E) 1412 * (or "off" if inverted) in ledctl_mode2. The blink 1413 * logic in hardware only works when mode is set to "on" 1414 * so it must be changed accordingly when the mode is 1415 * "off" and inverted. 1416 */ 1417 ledctl_blink = hw->mac.ledctl_mode2; 1418 for (i = 0; i < 32; i += 8) { 1419 u32 mode = (hw->mac.ledctl_mode2 >> i) & 1420 E1000_LEDCTL_LED0_MODE_MASK; 1421 u32 led_default = hw->mac.ledctl_default >> i; 1422 1423 if ((!(led_default & E1000_LEDCTL_LED0_IVRT) && 1424 (mode == E1000_LEDCTL_MODE_LED_ON)) || 1425 ((led_default & E1000_LEDCTL_LED0_IVRT) && 1426 (mode == E1000_LEDCTL_MODE_LED_OFF))) { 1427 ledctl_blink &= 1428 ~(E1000_LEDCTL_LED0_MODE_MASK << i); 1429 ledctl_blink |= (E1000_LEDCTL_LED0_BLINK | 1430 E1000_LEDCTL_MODE_LED_ON) << i; 1431 } 1432 } 1433 } 1434 1435 wr32(E1000_LEDCTL, ledctl_blink); 1436 1437 return 0; 1438} 1439 1440/** 1441 * igb_led_off - Turn LED off 1442 * @hw: pointer to the HW structure 1443 * 1444 * Turn LED off. 1445 **/ 1446s32 igb_led_off(struct e1000_hw *hw) 1447{ 1448 switch (hw->phy.media_type) { 1449 case e1000_media_type_copper: 1450 wr32(E1000_LEDCTL, hw->mac.ledctl_mode1); 1451 break; 1452 default: 1453 break; 1454 } 1455 1456 return 0; 1457} 1458 1459/** 1460 * igb_disable_pcie_master - Disables PCI-express master access 1461 * @hw: pointer to the HW structure 1462 * 1463 * Returns 0 (0) if successful, else returns -10 1464 * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused 1465 * the master requests to be disabled. 1466 * 1467 * Disables PCI-Express master access and verifies there are no pending 1468 * requests. 1469 **/ 1470s32 igb_disable_pcie_master(struct e1000_hw *hw) 1471{ 1472 u32 ctrl; 1473 s32 timeout = MASTER_DISABLE_TIMEOUT; 1474 s32 ret_val = 0; 1475 1476 if (hw->bus.type != e1000_bus_type_pci_express) 1477 goto out; 1478 1479 ctrl = rd32(E1000_CTRL); 1480 ctrl |= E1000_CTRL_GIO_MASTER_DISABLE; 1481 wr32(E1000_CTRL, ctrl); 1482 1483 while (timeout) { 1484 if (!(rd32(E1000_STATUS) & 1485 E1000_STATUS_GIO_MASTER_ENABLE)) 1486 break; 1487 udelay(100); 1488 timeout--; 1489 } 1490 1491 if (!timeout) { 1492 hw_dbg("Master requests are pending.\n"); 1493 ret_val = -E1000_ERR_MASTER_REQUESTS_PENDING; 1494 goto out; 1495 } 1496 1497out: 1498 return ret_val; 1499} 1500 1501/** 1502 * igb_validate_mdi_setting - Verify MDI/MDIx settings 1503 * @hw: pointer to the HW structure 1504 * 1505 * Verify that when not using auto-negotitation that MDI/MDIx is correctly 1506 * set, which is forced to MDI mode only. 1507 **/ 1508s32 igb_validate_mdi_setting(struct e1000_hw *hw) 1509{ 1510 s32 ret_val = 0; 1511 1512 /* All MDI settings are supported on 82580 and newer. */ 1513 if (hw->mac.type >= e1000_82580) 1514 goto out; 1515 1516 if (!hw->mac.autoneg && (hw->phy.mdix == 0 || hw->phy.mdix == 3)) { 1517 hw_dbg("Invalid MDI setting detected\n"); 1518 hw->phy.mdix = 1; 1519 ret_val = -E1000_ERR_CONFIG; 1520 goto out; 1521 } 1522 1523out: 1524 return ret_val; 1525} 1526 1527/** 1528 * igb_write_8bit_ctrl_reg - Write a 8bit CTRL register 1529 * @hw: pointer to the HW structure 1530 * @reg: 32bit register offset such as E1000_SCTL 1531 * @offset: register offset to write to 1532 * @data: data to write at register offset 1533 * 1534 * Writes an address/data control type register. There are several of these 1535 * and they all have the format address << 8 | data and bit 31 is polled for 1536 * completion. 1537 **/ 1538s32 igb_write_8bit_ctrl_reg(struct e1000_hw *hw, u32 reg, 1539 u32 offset, u8 data) 1540{ 1541 u32 i, regvalue = 0; 1542 s32 ret_val = 0; 1543 1544 /* Set up the address and data */ 1545 regvalue = ((u32)data) | (offset << E1000_GEN_CTL_ADDRESS_SHIFT); 1546 wr32(reg, regvalue); 1547 1548 /* Poll the ready bit to see if the MDI read completed */ 1549 for (i = 0; i < E1000_GEN_POLL_TIMEOUT; i++) { 1550 udelay(5); 1551 regvalue = rd32(reg); 1552 if (regvalue & E1000_GEN_CTL_READY) 1553 break; 1554 } 1555 if (!(regvalue & E1000_GEN_CTL_READY)) { 1556 hw_dbg("Reg %08x did not indicate ready\n", reg); 1557 ret_val = -E1000_ERR_PHY; 1558 goto out; 1559 } 1560 1561out: 1562 return ret_val; 1563} 1564 1565/** 1566 * igb_enable_mng_pass_thru - Enable processing of ARP's 1567 * @hw: pointer to the HW structure 1568 * 1569 * Verifies the hardware needs to leave interface enabled so that frames can 1570 * be directed to and from the management interface. 1571 **/ 1572bool igb_enable_mng_pass_thru(struct e1000_hw *hw) 1573{ 1574 u32 manc; 1575 u32 fwsm, factps; 1576 bool ret_val = false; 1577 1578 if (!hw->mac.asf_firmware_present) 1579 goto out; 1580 1581 manc = rd32(E1000_MANC); 1582 1583 if (!(manc & E1000_MANC_RCV_TCO_EN)) 1584 goto out; 1585 1586 if (hw->mac.arc_subsystem_valid) { 1587 fwsm = rd32(E1000_FWSM); 1588 factps = rd32(E1000_FACTPS); 1589 1590 if (!(factps & E1000_FACTPS_MNGCG) && 1591 ((fwsm & E1000_FWSM_MODE_MASK) == 1592 (e1000_mng_mode_pt << E1000_FWSM_MODE_SHIFT))) { 1593 ret_val = true; 1594 goto out; 1595 } 1596 } else { 1597 if ((manc & E1000_MANC_SMBUS_EN) && 1598 !(manc & E1000_MANC_ASF_EN)) { 1599 ret_val = true; 1600 goto out; 1601 } 1602 } 1603 1604out: 1605 return ret_val; 1606} 1607