e1000_mac.c revision cf7ed221714c36848b257311b316452e274f7e15
1/******************************************************************************* 2 3 Intel(R) Gigabit Ethernet Linux driver 4 Copyright(c) 2007-2013 Intel Corporation. 5 6 This program is free software; you can redistribute it and/or modify it 7 under the terms and conditions of the GNU General Public License, 8 version 2, as published by the Free Software Foundation. 9 10 This program is distributed in the hope it will be useful, but WITHOUT 11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 13 more details. 14 15 You should have received a copy of the GNU General Public License along with 16 this program; if not, write to the Free Software Foundation, Inc., 17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. 18 19 The full GNU General Public License is included in this distribution in 20 the file called "COPYING". 21 22 Contact Information: 23 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> 24 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 25 26*******************************************************************************/ 27 28#include <linux/if_ether.h> 29#include <linux/delay.h> 30#include <linux/pci.h> 31#include <linux/netdevice.h> 32#include <linux/etherdevice.h> 33 34#include "e1000_mac.h" 35 36#include "igb.h" 37 38static s32 igb_set_default_fc(struct e1000_hw *hw); 39static s32 igb_set_fc_watermarks(struct e1000_hw *hw); 40 41/** 42 * igb_get_bus_info_pcie - Get PCIe bus information 43 * @hw: pointer to the HW structure 44 * 45 * Determines and stores the system bus information for a particular 46 * network interface. The following bus information is determined and stored: 47 * bus speed, bus width, type (PCIe), and PCIe function. 48 **/ 49s32 igb_get_bus_info_pcie(struct e1000_hw *hw) 50{ 51 struct e1000_bus_info *bus = &hw->bus; 52 s32 ret_val; 53 u32 reg; 54 u16 pcie_link_status; 55 56 bus->type = e1000_bus_type_pci_express; 57 58 ret_val = igb_read_pcie_cap_reg(hw, 59 PCI_EXP_LNKSTA, 60 &pcie_link_status); 61 if (ret_val) { 62 bus->width = e1000_bus_width_unknown; 63 bus->speed = e1000_bus_speed_unknown; 64 } else { 65 switch (pcie_link_status & PCI_EXP_LNKSTA_CLS) { 66 case PCI_EXP_LNKSTA_CLS_2_5GB: 67 bus->speed = e1000_bus_speed_2500; 68 break; 69 case PCI_EXP_LNKSTA_CLS_5_0GB: 70 bus->speed = e1000_bus_speed_5000; 71 break; 72 default: 73 bus->speed = e1000_bus_speed_unknown; 74 break; 75 } 76 77 bus->width = (enum e1000_bus_width)((pcie_link_status & 78 PCI_EXP_LNKSTA_NLW) >> 79 PCI_EXP_LNKSTA_NLW_SHIFT); 80 } 81 82 reg = rd32(E1000_STATUS); 83 bus->func = (reg & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT; 84 85 return 0; 86} 87 88/** 89 * igb_clear_vfta - Clear VLAN filter table 90 * @hw: pointer to the HW structure 91 * 92 * Clears the register array which contains the VLAN filter table by 93 * setting all the values to 0. 94 **/ 95void igb_clear_vfta(struct e1000_hw *hw) 96{ 97 u32 offset; 98 99 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { 100 array_wr32(E1000_VFTA, offset, 0); 101 wrfl(); 102 } 103} 104 105/** 106 * igb_write_vfta - Write value to VLAN filter table 107 * @hw: pointer to the HW structure 108 * @offset: register offset in VLAN filter table 109 * @value: register value written to VLAN filter table 110 * 111 * Writes value at the given offset in the register array which stores 112 * the VLAN filter table. 113 **/ 114static void igb_write_vfta(struct e1000_hw *hw, u32 offset, u32 value) 115{ 116 array_wr32(E1000_VFTA, offset, value); 117 wrfl(); 118} 119 120/* Due to a hw errata, if the host tries to configure the VFTA register 121 * while performing queries from the BMC or DMA, then the VFTA in some 122 * cases won't be written. 123 */ 124 125/** 126 * igb_clear_vfta_i350 - Clear VLAN filter table 127 * @hw: pointer to the HW structure 128 * 129 * Clears the register array which contains the VLAN filter table by 130 * setting all the values to 0. 131 **/ 132void igb_clear_vfta_i350(struct e1000_hw *hw) 133{ 134 u32 offset; 135 int i; 136 137 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { 138 for (i = 0; i < 10; i++) 139 array_wr32(E1000_VFTA, offset, 0); 140 141 wrfl(); 142 } 143} 144 145/** 146 * igb_write_vfta_i350 - Write value to VLAN filter table 147 * @hw: pointer to the HW structure 148 * @offset: register offset in VLAN filter table 149 * @value: register value written to VLAN filter table 150 * 151 * Writes value at the given offset in the register array which stores 152 * the VLAN filter table. 153 **/ 154static void igb_write_vfta_i350(struct e1000_hw *hw, u32 offset, u32 value) 155{ 156 int i; 157 158 for (i = 0; i < 10; i++) 159 array_wr32(E1000_VFTA, offset, value); 160 161 wrfl(); 162} 163 164/** 165 * igb_init_rx_addrs - Initialize receive address's 166 * @hw: pointer to the HW structure 167 * @rar_count: receive address registers 168 * 169 * Setups the receive address registers by setting the base receive address 170 * register to the devices MAC address and clearing all the other receive 171 * address registers to 0. 172 **/ 173void igb_init_rx_addrs(struct e1000_hw *hw, u16 rar_count) 174{ 175 u32 i; 176 u8 mac_addr[ETH_ALEN] = {0}; 177 178 /* Setup the receive address */ 179 hw_dbg("Programming MAC Address into RAR[0]\n"); 180 181 hw->mac.ops.rar_set(hw, hw->mac.addr, 0); 182 183 /* Zero out the other (rar_entry_count - 1) receive addresses */ 184 hw_dbg("Clearing RAR[1-%u]\n", rar_count-1); 185 for (i = 1; i < rar_count; i++) 186 hw->mac.ops.rar_set(hw, mac_addr, i); 187} 188 189/** 190 * igb_vfta_set - enable or disable vlan in VLAN filter table 191 * @hw: pointer to the HW structure 192 * @vid: VLAN id to add or remove 193 * @add: if true add filter, if false remove 194 * 195 * Sets or clears a bit in the VLAN filter table array based on VLAN id 196 * and if we are adding or removing the filter 197 **/ 198s32 igb_vfta_set(struct e1000_hw *hw, u32 vid, bool add) 199{ 200 u32 index = (vid >> E1000_VFTA_ENTRY_SHIFT) & E1000_VFTA_ENTRY_MASK; 201 u32 mask = 1 << (vid & E1000_VFTA_ENTRY_BIT_SHIFT_MASK); 202 u32 vfta; 203 struct igb_adapter *adapter = hw->back; 204 s32 ret_val = 0; 205 206 vfta = adapter->shadow_vfta[index]; 207 208 /* bit was set/cleared before we started */ 209 if ((!!(vfta & mask)) == add) { 210 ret_val = -E1000_ERR_CONFIG; 211 } else { 212 if (add) 213 vfta |= mask; 214 else 215 vfta &= ~mask; 216 } 217 if ((hw->mac.type == e1000_i350) || (hw->mac.type == e1000_i354)) 218 igb_write_vfta_i350(hw, index, vfta); 219 else 220 igb_write_vfta(hw, index, vfta); 221 adapter->shadow_vfta[index] = vfta; 222 223 return ret_val; 224} 225 226/** 227 * igb_check_alt_mac_addr - Check for alternate MAC addr 228 * @hw: pointer to the HW structure 229 * 230 * Checks the nvm for an alternate MAC address. An alternate MAC address 231 * can be setup by pre-boot software and must be treated like a permanent 232 * address and must override the actual permanent MAC address. If an 233 * alternate MAC address is found it is saved in the hw struct and 234 * programmed into RAR0 and the function returns success, otherwise the 235 * function returns an error. 236 **/ 237s32 igb_check_alt_mac_addr(struct e1000_hw *hw) 238{ 239 u32 i; 240 s32 ret_val = 0; 241 u16 offset, nvm_alt_mac_addr_offset, nvm_data; 242 u8 alt_mac_addr[ETH_ALEN]; 243 244 /* Alternate MAC address is handled by the option ROM for 82580 245 * and newer. SW support not required. 246 */ 247 if (hw->mac.type >= e1000_82580) 248 goto out; 249 250 ret_val = hw->nvm.ops.read(hw, NVM_ALT_MAC_ADDR_PTR, 1, 251 &nvm_alt_mac_addr_offset); 252 if (ret_val) { 253 hw_dbg("NVM Read Error\n"); 254 goto out; 255 } 256 257 if ((nvm_alt_mac_addr_offset == 0xFFFF) || 258 (nvm_alt_mac_addr_offset == 0x0000)) 259 /* There is no Alternate MAC Address */ 260 goto out; 261 262 if (hw->bus.func == E1000_FUNC_1) 263 nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN1; 264 if (hw->bus.func == E1000_FUNC_2) 265 nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN2; 266 267 if (hw->bus.func == E1000_FUNC_3) 268 nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN3; 269 for (i = 0; i < ETH_ALEN; i += 2) { 270 offset = nvm_alt_mac_addr_offset + (i >> 1); 271 ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data); 272 if (ret_val) { 273 hw_dbg("NVM Read Error\n"); 274 goto out; 275 } 276 277 alt_mac_addr[i] = (u8)(nvm_data & 0xFF); 278 alt_mac_addr[i + 1] = (u8)(nvm_data >> 8); 279 } 280 281 /* if multicast bit is set, the alternate address will not be used */ 282 if (is_multicast_ether_addr(alt_mac_addr)) { 283 hw_dbg("Ignoring Alternate Mac Address with MC bit set\n"); 284 goto out; 285 } 286 287 /* We have a valid alternate MAC address, and we want to treat it the 288 * same as the normal permanent MAC address stored by the HW into the 289 * RAR. Do this by mapping this address into RAR0. 290 */ 291 hw->mac.ops.rar_set(hw, alt_mac_addr, 0); 292 293out: 294 return ret_val; 295} 296 297/** 298 * igb_rar_set - Set receive address register 299 * @hw: pointer to the HW structure 300 * @addr: pointer to the receive address 301 * @index: receive address array register 302 * 303 * Sets the receive address array register at index to the address passed 304 * in by addr. 305 **/ 306void igb_rar_set(struct e1000_hw *hw, u8 *addr, u32 index) 307{ 308 u32 rar_low, rar_high; 309 310 /* HW expects these in little endian so we reverse the byte order 311 * from network order (big endian) to little endian 312 */ 313 rar_low = ((u32) addr[0] | 314 ((u32) addr[1] << 8) | 315 ((u32) addr[2] << 16) | ((u32) addr[3] << 24)); 316 317 rar_high = ((u32) addr[4] | ((u32) addr[5] << 8)); 318 319 /* If MAC address zero, no need to set the AV bit */ 320 if (rar_low || rar_high) 321 rar_high |= E1000_RAH_AV; 322 323 /* Some bridges will combine consecutive 32-bit writes into 324 * a single burst write, which will malfunction on some parts. 325 * The flushes avoid this. 326 */ 327 wr32(E1000_RAL(index), rar_low); 328 wrfl(); 329 wr32(E1000_RAH(index), rar_high); 330 wrfl(); 331} 332 333/** 334 * igb_mta_set - Set multicast filter table address 335 * @hw: pointer to the HW structure 336 * @hash_value: determines the MTA register and bit to set 337 * 338 * The multicast table address is a register array of 32-bit registers. 339 * The hash_value is used to determine what register the bit is in, the 340 * current value is read, the new bit is OR'd in and the new value is 341 * written back into the register. 342 **/ 343void igb_mta_set(struct e1000_hw *hw, u32 hash_value) 344{ 345 u32 hash_bit, hash_reg, mta; 346 347 /* The MTA is a register array of 32-bit registers. It is 348 * treated like an array of (32*mta_reg_count) bits. We want to 349 * set bit BitArray[hash_value]. So we figure out what register 350 * the bit is in, read it, OR in the new bit, then write 351 * back the new value. The (hw->mac.mta_reg_count - 1) serves as a 352 * mask to bits 31:5 of the hash value which gives us the 353 * register we're modifying. The hash bit within that register 354 * is determined by the lower 5 bits of the hash value. 355 */ 356 hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); 357 hash_bit = hash_value & 0x1F; 358 359 mta = array_rd32(E1000_MTA, hash_reg); 360 361 mta |= (1 << hash_bit); 362 363 array_wr32(E1000_MTA, hash_reg, mta); 364 wrfl(); 365} 366 367/** 368 * igb_hash_mc_addr - Generate a multicast hash value 369 * @hw: pointer to the HW structure 370 * @mc_addr: pointer to a multicast address 371 * 372 * Generates a multicast address hash value which is used to determine 373 * the multicast filter table array address and new table value. See 374 * igb_mta_set() 375 **/ 376static u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr) 377{ 378 u32 hash_value, hash_mask; 379 u8 bit_shift = 0; 380 381 /* Register count multiplied by bits per register */ 382 hash_mask = (hw->mac.mta_reg_count * 32) - 1; 383 384 /* For a mc_filter_type of 0, bit_shift is the number of left-shifts 385 * where 0xFF would still fall within the hash mask. 386 */ 387 while (hash_mask >> bit_shift != 0xFF) 388 bit_shift++; 389 390 /* The portion of the address that is used for the hash table 391 * is determined by the mc_filter_type setting. 392 * The algorithm is such that there is a total of 8 bits of shifting. 393 * The bit_shift for a mc_filter_type of 0 represents the number of 394 * left-shifts where the MSB of mc_addr[5] would still fall within 395 * the hash_mask. Case 0 does this exactly. Since there are a total 396 * of 8 bits of shifting, then mc_addr[4] will shift right the 397 * remaining number of bits. Thus 8 - bit_shift. The rest of the 398 * cases are a variation of this algorithm...essentially raising the 399 * number of bits to shift mc_addr[5] left, while still keeping the 400 * 8-bit shifting total. 401 * 402 * For example, given the following Destination MAC Address and an 403 * mta register count of 128 (thus a 4096-bit vector and 0xFFF mask), 404 * we can see that the bit_shift for case 0 is 4. These are the hash 405 * values resulting from each mc_filter_type... 406 * [0] [1] [2] [3] [4] [5] 407 * 01 AA 00 12 34 56 408 * LSB MSB 409 * 410 * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563 411 * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6 412 * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163 413 * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634 414 */ 415 switch (hw->mac.mc_filter_type) { 416 default: 417 case 0: 418 break; 419 case 1: 420 bit_shift += 1; 421 break; 422 case 2: 423 bit_shift += 2; 424 break; 425 case 3: 426 bit_shift += 4; 427 break; 428 } 429 430 hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) | 431 (((u16) mc_addr[5]) << bit_shift))); 432 433 return hash_value; 434} 435 436/** 437 * igb_update_mc_addr_list - Update Multicast addresses 438 * @hw: pointer to the HW structure 439 * @mc_addr_list: array of multicast addresses to program 440 * @mc_addr_count: number of multicast addresses to program 441 * 442 * Updates entire Multicast Table Array. 443 * The caller must have a packed mc_addr_list of multicast addresses. 444 **/ 445void igb_update_mc_addr_list(struct e1000_hw *hw, 446 u8 *mc_addr_list, u32 mc_addr_count) 447{ 448 u32 hash_value, hash_bit, hash_reg; 449 int i; 450 451 /* clear mta_shadow */ 452 memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); 453 454 /* update mta_shadow from mc_addr_list */ 455 for (i = 0; (u32) i < mc_addr_count; i++) { 456 hash_value = igb_hash_mc_addr(hw, mc_addr_list); 457 458 hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); 459 hash_bit = hash_value & 0x1F; 460 461 hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit); 462 mc_addr_list += (ETH_ALEN); 463 } 464 465 /* replace the entire MTA table */ 466 for (i = hw->mac.mta_reg_count - 1; i >= 0; i--) 467 array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]); 468 wrfl(); 469} 470 471/** 472 * igb_clear_hw_cntrs_base - Clear base hardware counters 473 * @hw: pointer to the HW structure 474 * 475 * Clears the base hardware counters by reading the counter registers. 476 **/ 477void igb_clear_hw_cntrs_base(struct e1000_hw *hw) 478{ 479 rd32(E1000_CRCERRS); 480 rd32(E1000_SYMERRS); 481 rd32(E1000_MPC); 482 rd32(E1000_SCC); 483 rd32(E1000_ECOL); 484 rd32(E1000_MCC); 485 rd32(E1000_LATECOL); 486 rd32(E1000_COLC); 487 rd32(E1000_DC); 488 rd32(E1000_SEC); 489 rd32(E1000_RLEC); 490 rd32(E1000_XONRXC); 491 rd32(E1000_XONTXC); 492 rd32(E1000_XOFFRXC); 493 rd32(E1000_XOFFTXC); 494 rd32(E1000_FCRUC); 495 rd32(E1000_GPRC); 496 rd32(E1000_BPRC); 497 rd32(E1000_MPRC); 498 rd32(E1000_GPTC); 499 rd32(E1000_GORCL); 500 rd32(E1000_GORCH); 501 rd32(E1000_GOTCL); 502 rd32(E1000_GOTCH); 503 rd32(E1000_RNBC); 504 rd32(E1000_RUC); 505 rd32(E1000_RFC); 506 rd32(E1000_ROC); 507 rd32(E1000_RJC); 508 rd32(E1000_TORL); 509 rd32(E1000_TORH); 510 rd32(E1000_TOTL); 511 rd32(E1000_TOTH); 512 rd32(E1000_TPR); 513 rd32(E1000_TPT); 514 rd32(E1000_MPTC); 515 rd32(E1000_BPTC); 516} 517 518/** 519 * igb_check_for_copper_link - Check for link (Copper) 520 * @hw: pointer to the HW structure 521 * 522 * Checks to see of the link status of the hardware has changed. If a 523 * change in link status has been detected, then we read the PHY registers 524 * to get the current speed/duplex if link exists. 525 **/ 526s32 igb_check_for_copper_link(struct e1000_hw *hw) 527{ 528 struct e1000_mac_info *mac = &hw->mac; 529 s32 ret_val; 530 bool link; 531 532 /* We only want to go out to the PHY registers to see if Auto-Neg 533 * has completed and/or if our link status has changed. The 534 * get_link_status flag is set upon receiving a Link Status 535 * Change or Rx Sequence Error interrupt. 536 */ 537 if (!mac->get_link_status) { 538 ret_val = 0; 539 goto out; 540 } 541 542 /* First we want to see if the MII Status Register reports 543 * link. If so, then we want to get the current speed/duplex 544 * of the PHY. 545 */ 546 ret_val = igb_phy_has_link(hw, 1, 0, &link); 547 if (ret_val) 548 goto out; 549 550 if (!link) 551 goto out; /* No link detected */ 552 553 mac->get_link_status = false; 554 555 /* Check if there was DownShift, must be checked 556 * immediately after link-up 557 */ 558 igb_check_downshift(hw); 559 560 /* If we are forcing speed/duplex, then we simply return since 561 * we have already determined whether we have link or not. 562 */ 563 if (!mac->autoneg) { 564 ret_val = -E1000_ERR_CONFIG; 565 goto out; 566 } 567 568 /* Auto-Neg is enabled. Auto Speed Detection takes care 569 * of MAC speed/duplex configuration. So we only need to 570 * configure Collision Distance in the MAC. 571 */ 572 igb_config_collision_dist(hw); 573 574 /* Configure Flow Control now that Auto-Neg has completed. 575 * First, we need to restore the desired flow control 576 * settings because we may have had to re-autoneg with a 577 * different link partner. 578 */ 579 ret_val = igb_config_fc_after_link_up(hw); 580 if (ret_val) 581 hw_dbg("Error configuring flow control\n"); 582 583out: 584 return ret_val; 585} 586 587/** 588 * igb_setup_link - Setup flow control and link settings 589 * @hw: pointer to the HW structure 590 * 591 * Determines which flow control settings to use, then configures flow 592 * control. Calls the appropriate media-specific link configuration 593 * function. Assuming the adapter has a valid link partner, a valid link 594 * should be established. Assumes the hardware has previously been reset 595 * and the transmitter and receiver are not enabled. 596 **/ 597s32 igb_setup_link(struct e1000_hw *hw) 598{ 599 s32 ret_val = 0; 600 601 /* In the case of the phy reset being blocked, we already have a link. 602 * We do not need to set it up again. 603 */ 604 if (igb_check_reset_block(hw)) 605 goto out; 606 607 /* If requested flow control is set to default, set flow control 608 * based on the EEPROM flow control settings. 609 */ 610 if (hw->fc.requested_mode == e1000_fc_default) { 611 ret_val = igb_set_default_fc(hw); 612 if (ret_val) 613 goto out; 614 } 615 616 /* We want to save off the original Flow Control configuration just 617 * in case we get disconnected and then reconnected into a different 618 * hub or switch with different Flow Control capabilities. 619 */ 620 hw->fc.current_mode = hw->fc.requested_mode; 621 622 hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.current_mode); 623 624 /* Call the necessary media_type subroutine to configure the link. */ 625 ret_val = hw->mac.ops.setup_physical_interface(hw); 626 if (ret_val) 627 goto out; 628 629 /* Initialize the flow control address, type, and PAUSE timer 630 * registers to their default values. This is done even if flow 631 * control is disabled, because it does not hurt anything to 632 * initialize these registers. 633 */ 634 hw_dbg("Initializing the Flow Control address, type and timer regs\n"); 635 wr32(E1000_FCT, FLOW_CONTROL_TYPE); 636 wr32(E1000_FCAH, FLOW_CONTROL_ADDRESS_HIGH); 637 wr32(E1000_FCAL, FLOW_CONTROL_ADDRESS_LOW); 638 639 wr32(E1000_FCTTV, hw->fc.pause_time); 640 641 ret_val = igb_set_fc_watermarks(hw); 642 643out: 644 645 return ret_val; 646} 647 648/** 649 * igb_config_collision_dist - Configure collision distance 650 * @hw: pointer to the HW structure 651 * 652 * Configures the collision distance to the default value and is used 653 * during link setup. Currently no func pointer exists and all 654 * implementations are handled in the generic version of this function. 655 **/ 656void igb_config_collision_dist(struct e1000_hw *hw) 657{ 658 u32 tctl; 659 660 tctl = rd32(E1000_TCTL); 661 662 tctl &= ~E1000_TCTL_COLD; 663 tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT; 664 665 wr32(E1000_TCTL, tctl); 666 wrfl(); 667} 668 669/** 670 * igb_set_fc_watermarks - Set flow control high/low watermarks 671 * @hw: pointer to the HW structure 672 * 673 * Sets the flow control high/low threshold (watermark) registers. If 674 * flow control XON frame transmission is enabled, then set XON frame 675 * tansmission as well. 676 **/ 677static s32 igb_set_fc_watermarks(struct e1000_hw *hw) 678{ 679 s32 ret_val = 0; 680 u32 fcrtl = 0, fcrth = 0; 681 682 /* Set the flow control receive threshold registers. Normally, 683 * these registers will be set to a default threshold that may be 684 * adjusted later by the driver's runtime code. However, if the 685 * ability to transmit pause frames is not enabled, then these 686 * registers will be set to 0. 687 */ 688 if (hw->fc.current_mode & e1000_fc_tx_pause) { 689 /* We need to set up the Receive Threshold high and low water 690 * marks as well as (optionally) enabling the transmission of 691 * XON frames. 692 */ 693 fcrtl = hw->fc.low_water; 694 if (hw->fc.send_xon) 695 fcrtl |= E1000_FCRTL_XONE; 696 697 fcrth = hw->fc.high_water; 698 } 699 wr32(E1000_FCRTL, fcrtl); 700 wr32(E1000_FCRTH, fcrth); 701 702 return ret_val; 703} 704 705/** 706 * igb_set_default_fc - Set flow control default values 707 * @hw: pointer to the HW structure 708 * 709 * Read the EEPROM for the default values for flow control and store the 710 * values. 711 **/ 712static s32 igb_set_default_fc(struct e1000_hw *hw) 713{ 714 s32 ret_val = 0; 715 u16 nvm_data; 716 717 /* Read and store word 0x0F of the EEPROM. This word contains bits 718 * that determine the hardware's default PAUSE (flow control) mode, 719 * a bit that determines whether the HW defaults to enabling or 720 * disabling auto-negotiation, and the direction of the 721 * SW defined pins. If there is no SW over-ride of the flow 722 * control setting, then the variable hw->fc will 723 * be initialized based on a value in the EEPROM. 724 */ 725 ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG, 1, &nvm_data); 726 727 if (ret_val) { 728 hw_dbg("NVM Read Error\n"); 729 goto out; 730 } 731 732 if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0) 733 hw->fc.requested_mode = e1000_fc_none; 734 else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 735 NVM_WORD0F_ASM_DIR) 736 hw->fc.requested_mode = e1000_fc_tx_pause; 737 else 738 hw->fc.requested_mode = e1000_fc_full; 739 740out: 741 return ret_val; 742} 743 744/** 745 * igb_force_mac_fc - Force the MAC's flow control settings 746 * @hw: pointer to the HW structure 747 * 748 * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the 749 * device control register to reflect the adapter settings. TFCE and RFCE 750 * need to be explicitly set by software when a copper PHY is used because 751 * autonegotiation is managed by the PHY rather than the MAC. Software must 752 * also configure these bits when link is forced on a fiber connection. 753 **/ 754s32 igb_force_mac_fc(struct e1000_hw *hw) 755{ 756 u32 ctrl; 757 s32 ret_val = 0; 758 759 ctrl = rd32(E1000_CTRL); 760 761 /* Because we didn't get link via the internal auto-negotiation 762 * mechanism (we either forced link or we got link via PHY 763 * auto-neg), we have to manually enable/disable transmit an 764 * receive flow control. 765 * 766 * The "Case" statement below enables/disable flow control 767 * according to the "hw->fc.current_mode" parameter. 768 * 769 * The possible values of the "fc" parameter are: 770 * 0: Flow control is completely disabled 771 * 1: Rx flow control is enabled (we can receive pause 772 * frames but not send pause frames). 773 * 2: Tx flow control is enabled (we can send pause frames 774 * frames but we do not receive pause frames). 775 * 3: Both Rx and TX flow control (symmetric) is enabled. 776 * other: No other values should be possible at this point. 777 */ 778 hw_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode); 779 780 switch (hw->fc.current_mode) { 781 case e1000_fc_none: 782 ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); 783 break; 784 case e1000_fc_rx_pause: 785 ctrl &= (~E1000_CTRL_TFCE); 786 ctrl |= E1000_CTRL_RFCE; 787 break; 788 case e1000_fc_tx_pause: 789 ctrl &= (~E1000_CTRL_RFCE); 790 ctrl |= E1000_CTRL_TFCE; 791 break; 792 case e1000_fc_full: 793 ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); 794 break; 795 default: 796 hw_dbg("Flow control param set incorrectly\n"); 797 ret_val = -E1000_ERR_CONFIG; 798 goto out; 799 } 800 801 wr32(E1000_CTRL, ctrl); 802 803out: 804 return ret_val; 805} 806 807/** 808 * igb_config_fc_after_link_up - Configures flow control after link 809 * @hw: pointer to the HW structure 810 * 811 * Checks the status of auto-negotiation after link up to ensure that the 812 * speed and duplex were not forced. If the link needed to be forced, then 813 * flow control needs to be forced also. If auto-negotiation is enabled 814 * and did not fail, then we configure flow control based on our link 815 * partner. 816 **/ 817s32 igb_config_fc_after_link_up(struct e1000_hw *hw) 818{ 819 struct e1000_mac_info *mac = &hw->mac; 820 s32 ret_val = 0; 821 u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg; 822 u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; 823 u16 speed, duplex; 824 825 /* Check for the case where we have fiber media and auto-neg failed 826 * so we had to force link. In this case, we need to force the 827 * configuration of the MAC to match the "fc" parameter. 828 */ 829 if (mac->autoneg_failed) { 830 if (hw->phy.media_type == e1000_media_type_internal_serdes) 831 ret_val = igb_force_mac_fc(hw); 832 } else { 833 if (hw->phy.media_type == e1000_media_type_copper) 834 ret_val = igb_force_mac_fc(hw); 835 } 836 837 if (ret_val) { 838 hw_dbg("Error forcing flow control settings\n"); 839 goto out; 840 } 841 842 /* Check for the case where we have copper media and auto-neg is 843 * enabled. In this case, we need to check and see if Auto-Neg 844 * has completed, and if so, how the PHY and link partner has 845 * flow control configured. 846 */ 847 if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) { 848 /* Read the MII Status Register and check to see if AutoNeg 849 * has completed. We read this twice because this reg has 850 * some "sticky" (latched) bits. 851 */ 852 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, 853 &mii_status_reg); 854 if (ret_val) 855 goto out; 856 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, 857 &mii_status_reg); 858 if (ret_val) 859 goto out; 860 861 if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) { 862 hw_dbg("Copper PHY and Auto Neg " 863 "has not completed.\n"); 864 goto out; 865 } 866 867 /* The AutoNeg process has completed, so we now need to 868 * read both the Auto Negotiation Advertisement 869 * Register (Address 4) and the Auto_Negotiation Base 870 * Page Ability Register (Address 5) to determine how 871 * flow control was negotiated. 872 */ 873 ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV, 874 &mii_nway_adv_reg); 875 if (ret_val) 876 goto out; 877 ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY, 878 &mii_nway_lp_ability_reg); 879 if (ret_val) 880 goto out; 881 882 /* Two bits in the Auto Negotiation Advertisement Register 883 * (Address 4) and two bits in the Auto Negotiation Base 884 * Page Ability Register (Address 5) determine flow control 885 * for both the PHY and the link partner. The following 886 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, 887 * 1999, describes these PAUSE resolution bits and how flow 888 * control is determined based upon these settings. 889 * NOTE: DC = Don't Care 890 * 891 * LOCAL DEVICE | LINK PARTNER 892 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution 893 *-------|---------|-------|---------|-------------------- 894 * 0 | 0 | DC | DC | e1000_fc_none 895 * 0 | 1 | 0 | DC | e1000_fc_none 896 * 0 | 1 | 1 | 0 | e1000_fc_none 897 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 898 * 1 | 0 | 0 | DC | e1000_fc_none 899 * 1 | DC | 1 | DC | e1000_fc_full 900 * 1 | 1 | 0 | 0 | e1000_fc_none 901 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 902 * 903 * Are both PAUSE bits set to 1? If so, this implies 904 * Symmetric Flow Control is enabled at both ends. The 905 * ASM_DIR bits are irrelevant per the spec. 906 * 907 * For Symmetric Flow Control: 908 * 909 * LOCAL DEVICE | LINK PARTNER 910 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 911 *-------|---------|-------|---------|-------------------- 912 * 1 | DC | 1 | DC | E1000_fc_full 913 * 914 */ 915 if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 916 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { 917 /* Now we need to check if the user selected RX ONLY 918 * of pause frames. In this case, we had to advertise 919 * FULL flow control because we could not advertise RX 920 * ONLY. Hence, we must now check to see if we need to 921 * turn OFF the TRANSMISSION of PAUSE frames. 922 */ 923 if (hw->fc.requested_mode == e1000_fc_full) { 924 hw->fc.current_mode = e1000_fc_full; 925 hw_dbg("Flow Control = FULL.\r\n"); 926 } else { 927 hw->fc.current_mode = e1000_fc_rx_pause; 928 hw_dbg("Flow Control = " 929 "RX PAUSE frames only.\r\n"); 930 } 931 } 932 /* For receiving PAUSE frames ONLY. 933 * 934 * LOCAL DEVICE | LINK PARTNER 935 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 936 *-------|---------|-------|---------|-------------------- 937 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 938 */ 939 else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && 940 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 941 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 942 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { 943 hw->fc.current_mode = e1000_fc_tx_pause; 944 hw_dbg("Flow Control = TX PAUSE frames only.\r\n"); 945 } 946 /* For transmitting PAUSE frames ONLY. 947 * 948 * LOCAL DEVICE | LINK PARTNER 949 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 950 *-------|---------|-------|---------|-------------------- 951 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 952 */ 953 else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 954 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 955 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 956 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { 957 hw->fc.current_mode = e1000_fc_rx_pause; 958 hw_dbg("Flow Control = RX PAUSE frames only.\r\n"); 959 } 960 /* Per the IEEE spec, at this point flow control should be 961 * disabled. However, we want to consider that we could 962 * be connected to a legacy switch that doesn't advertise 963 * desired flow control, but can be forced on the link 964 * partner. So if we advertised no flow control, that is 965 * what we will resolve to. If we advertised some kind of 966 * receive capability (Rx Pause Only or Full Flow Control) 967 * and the link partner advertised none, we will configure 968 * ourselves to enable Rx Flow Control only. We can do 969 * this safely for two reasons: If the link partner really 970 * didn't want flow control enabled, and we enable Rx, no 971 * harm done since we won't be receiving any PAUSE frames 972 * anyway. If the intent on the link partner was to have 973 * flow control enabled, then by us enabling RX only, we 974 * can at least receive pause frames and process them. 975 * This is a good idea because in most cases, since we are 976 * predominantly a server NIC, more times than not we will 977 * be asked to delay transmission of packets than asking 978 * our link partner to pause transmission of frames. 979 */ 980 else if ((hw->fc.requested_mode == e1000_fc_none) || 981 (hw->fc.requested_mode == e1000_fc_tx_pause) || 982 (hw->fc.strict_ieee)) { 983 hw->fc.current_mode = e1000_fc_none; 984 hw_dbg("Flow Control = NONE.\r\n"); 985 } else { 986 hw->fc.current_mode = e1000_fc_rx_pause; 987 hw_dbg("Flow Control = RX PAUSE frames only.\r\n"); 988 } 989 990 /* Now we need to do one last check... If we auto- 991 * negotiated to HALF DUPLEX, flow control should not be 992 * enabled per IEEE 802.3 spec. 993 */ 994 ret_val = hw->mac.ops.get_speed_and_duplex(hw, &speed, &duplex); 995 if (ret_val) { 996 hw_dbg("Error getting link speed and duplex\n"); 997 goto out; 998 } 999 1000 if (duplex == HALF_DUPLEX) 1001 hw->fc.current_mode = e1000_fc_none; 1002 1003 /* Now we call a subroutine to actually force the MAC 1004 * controller to use the correct flow control settings. 1005 */ 1006 ret_val = igb_force_mac_fc(hw); 1007 if (ret_val) { 1008 hw_dbg("Error forcing flow control settings\n"); 1009 goto out; 1010 } 1011 } 1012 /* Check for the case where we have SerDes media and auto-neg is 1013 * enabled. In this case, we need to check and see if Auto-Neg 1014 * has completed, and if so, how the PHY and link partner has 1015 * flow control configured. 1016 */ 1017 if ((hw->phy.media_type == e1000_media_type_internal_serdes) 1018 && mac->autoneg) { 1019 /* Read the PCS_LSTS and check to see if AutoNeg 1020 * has completed. 1021 */ 1022 pcs_status_reg = rd32(E1000_PCS_LSTAT); 1023 1024 if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) { 1025 hw_dbg("PCS Auto Neg has not completed.\n"); 1026 return ret_val; 1027 } 1028 1029 /* The AutoNeg process has completed, so we now need to 1030 * read both the Auto Negotiation Advertisement 1031 * Register (PCS_ANADV) and the Auto_Negotiation Base 1032 * Page Ability Register (PCS_LPAB) to determine how 1033 * flow control was negotiated. 1034 */ 1035 pcs_adv_reg = rd32(E1000_PCS_ANADV); 1036 pcs_lp_ability_reg = rd32(E1000_PCS_LPAB); 1037 1038 /* Two bits in the Auto Negotiation Advertisement Register 1039 * (PCS_ANADV) and two bits in the Auto Negotiation Base 1040 * Page Ability Register (PCS_LPAB) determine flow control 1041 * for both the PHY and the link partner. The following 1042 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, 1043 * 1999, describes these PAUSE resolution bits and how flow 1044 * control is determined based upon these settings. 1045 * NOTE: DC = Don't Care 1046 * 1047 * LOCAL DEVICE | LINK PARTNER 1048 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution 1049 *-------|---------|-------|---------|-------------------- 1050 * 0 | 0 | DC | DC | e1000_fc_none 1051 * 0 | 1 | 0 | DC | e1000_fc_none 1052 * 0 | 1 | 1 | 0 | e1000_fc_none 1053 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 1054 * 1 | 0 | 0 | DC | e1000_fc_none 1055 * 1 | DC | 1 | DC | e1000_fc_full 1056 * 1 | 1 | 0 | 0 | e1000_fc_none 1057 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 1058 * 1059 * Are both PAUSE bits set to 1? If so, this implies 1060 * Symmetric Flow Control is enabled at both ends. The 1061 * ASM_DIR bits are irrelevant per the spec. 1062 * 1063 * For Symmetric Flow Control: 1064 * 1065 * LOCAL DEVICE | LINK PARTNER 1066 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 1067 *-------|---------|-------|---------|-------------------- 1068 * 1 | DC | 1 | DC | e1000_fc_full 1069 * 1070 */ 1071 if ((pcs_adv_reg & E1000_TXCW_PAUSE) && 1072 (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) { 1073 /* Now we need to check if the user selected Rx ONLY 1074 * of pause frames. In this case, we had to advertise 1075 * FULL flow control because we could not advertise Rx 1076 * ONLY. Hence, we must now check to see if we need to 1077 * turn OFF the TRANSMISSION of PAUSE frames. 1078 */ 1079 if (hw->fc.requested_mode == e1000_fc_full) { 1080 hw->fc.current_mode = e1000_fc_full; 1081 hw_dbg("Flow Control = FULL.\n"); 1082 } else { 1083 hw->fc.current_mode = e1000_fc_rx_pause; 1084 hw_dbg("Flow Control = Rx PAUSE frames only.\n"); 1085 } 1086 } 1087 /* For receiving PAUSE frames ONLY. 1088 * 1089 * LOCAL DEVICE | LINK PARTNER 1090 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 1091 *-------|---------|-------|---------|-------------------- 1092 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 1093 */ 1094 else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) && 1095 (pcs_adv_reg & E1000_TXCW_ASM_DIR) && 1096 (pcs_lp_ability_reg & E1000_TXCW_PAUSE) && 1097 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { 1098 hw->fc.current_mode = e1000_fc_tx_pause; 1099 hw_dbg("Flow Control = Tx PAUSE frames only.\n"); 1100 } 1101 /* For transmitting PAUSE frames ONLY. 1102 * 1103 * LOCAL DEVICE | LINK PARTNER 1104 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 1105 *-------|---------|-------|---------|-------------------- 1106 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 1107 */ 1108 else if ((pcs_adv_reg & E1000_TXCW_PAUSE) && 1109 (pcs_adv_reg & E1000_TXCW_ASM_DIR) && 1110 !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) && 1111 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { 1112 hw->fc.current_mode = e1000_fc_rx_pause; 1113 hw_dbg("Flow Control = Rx PAUSE frames only.\n"); 1114 } else { 1115 /* Per the IEEE spec, at this point flow control 1116 * should be disabled. 1117 */ 1118 hw->fc.current_mode = e1000_fc_none; 1119 hw_dbg("Flow Control = NONE.\n"); 1120 } 1121 1122 /* Now we call a subroutine to actually force the MAC 1123 * controller to use the correct flow control settings. 1124 */ 1125 pcs_ctrl_reg = rd32(E1000_PCS_LCTL); 1126 pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL; 1127 wr32(E1000_PCS_LCTL, pcs_ctrl_reg); 1128 1129 ret_val = igb_force_mac_fc(hw); 1130 if (ret_val) { 1131 hw_dbg("Error forcing flow control settings\n"); 1132 return ret_val; 1133 } 1134 } 1135 1136out: 1137 return ret_val; 1138} 1139 1140/** 1141 * igb_get_speed_and_duplex_copper - Retrieve current speed/duplex 1142 * @hw: pointer to the HW structure 1143 * @speed: stores the current speed 1144 * @duplex: stores the current duplex 1145 * 1146 * Read the status register for the current speed/duplex and store the current 1147 * speed and duplex for copper connections. 1148 **/ 1149s32 igb_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, 1150 u16 *duplex) 1151{ 1152 u32 status; 1153 1154 status = rd32(E1000_STATUS); 1155 if (status & E1000_STATUS_SPEED_1000) { 1156 *speed = SPEED_1000; 1157 hw_dbg("1000 Mbs, "); 1158 } else if (status & E1000_STATUS_SPEED_100) { 1159 *speed = SPEED_100; 1160 hw_dbg("100 Mbs, "); 1161 } else { 1162 *speed = SPEED_10; 1163 hw_dbg("10 Mbs, "); 1164 } 1165 1166 if (status & E1000_STATUS_FD) { 1167 *duplex = FULL_DUPLEX; 1168 hw_dbg("Full Duplex\n"); 1169 } else { 1170 *duplex = HALF_DUPLEX; 1171 hw_dbg("Half Duplex\n"); 1172 } 1173 1174 /* Check if it is an I354 2.5Gb backplane connection. */ 1175 if (hw->mac.type == e1000_i354) { 1176 if ((status & E1000_STATUS_2P5_SKU) && 1177 !(status & E1000_STATUS_2P5_SKU_OVER)) { 1178 *speed = SPEED_2500; 1179 *duplex = FULL_DUPLEX; 1180 hw_dbg("2500 Mbs, "); 1181 hw_dbg("Full Duplex\n"); 1182 } 1183 } 1184 1185 return 0; 1186} 1187 1188/** 1189 * igb_get_hw_semaphore - Acquire hardware semaphore 1190 * @hw: pointer to the HW structure 1191 * 1192 * Acquire the HW semaphore to access the PHY or NVM 1193 **/ 1194s32 igb_get_hw_semaphore(struct e1000_hw *hw) 1195{ 1196 u32 swsm; 1197 s32 ret_val = 0; 1198 s32 timeout = hw->nvm.word_size + 1; 1199 s32 i = 0; 1200 1201 /* Get the SW semaphore */ 1202 while (i < timeout) { 1203 swsm = rd32(E1000_SWSM); 1204 if (!(swsm & E1000_SWSM_SMBI)) 1205 break; 1206 1207 udelay(50); 1208 i++; 1209 } 1210 1211 if (i == timeout) { 1212 hw_dbg("Driver can't access device - SMBI bit is set.\n"); 1213 ret_val = -E1000_ERR_NVM; 1214 goto out; 1215 } 1216 1217 /* Get the FW semaphore. */ 1218 for (i = 0; i < timeout; i++) { 1219 swsm = rd32(E1000_SWSM); 1220 wr32(E1000_SWSM, swsm | E1000_SWSM_SWESMBI); 1221 1222 /* Semaphore acquired if bit latched */ 1223 if (rd32(E1000_SWSM) & E1000_SWSM_SWESMBI) 1224 break; 1225 1226 udelay(50); 1227 } 1228 1229 if (i == timeout) { 1230 /* Release semaphores */ 1231 igb_put_hw_semaphore(hw); 1232 hw_dbg("Driver can't access the NVM\n"); 1233 ret_val = -E1000_ERR_NVM; 1234 goto out; 1235 } 1236 1237out: 1238 return ret_val; 1239} 1240 1241/** 1242 * igb_put_hw_semaphore - Release hardware semaphore 1243 * @hw: pointer to the HW structure 1244 * 1245 * Release hardware semaphore used to access the PHY or NVM 1246 **/ 1247void igb_put_hw_semaphore(struct e1000_hw *hw) 1248{ 1249 u32 swsm; 1250 1251 swsm = rd32(E1000_SWSM); 1252 1253 swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); 1254 1255 wr32(E1000_SWSM, swsm); 1256} 1257 1258/** 1259 * igb_get_auto_rd_done - Check for auto read completion 1260 * @hw: pointer to the HW structure 1261 * 1262 * Check EEPROM for Auto Read done bit. 1263 **/ 1264s32 igb_get_auto_rd_done(struct e1000_hw *hw) 1265{ 1266 s32 i = 0; 1267 s32 ret_val = 0; 1268 1269 1270 while (i < AUTO_READ_DONE_TIMEOUT) { 1271 if (rd32(E1000_EECD) & E1000_EECD_AUTO_RD) 1272 break; 1273 msleep(1); 1274 i++; 1275 } 1276 1277 if (i == AUTO_READ_DONE_TIMEOUT) { 1278 hw_dbg("Auto read by HW from NVM has not completed.\n"); 1279 ret_val = -E1000_ERR_RESET; 1280 goto out; 1281 } 1282 1283out: 1284 return ret_val; 1285} 1286 1287/** 1288 * igb_valid_led_default - Verify a valid default LED config 1289 * @hw: pointer to the HW structure 1290 * @data: pointer to the NVM (EEPROM) 1291 * 1292 * Read the EEPROM for the current default LED configuration. If the 1293 * LED configuration is not valid, set to a valid LED configuration. 1294 **/ 1295static s32 igb_valid_led_default(struct e1000_hw *hw, u16 *data) 1296{ 1297 s32 ret_val; 1298 1299 ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); 1300 if (ret_val) { 1301 hw_dbg("NVM Read Error\n"); 1302 goto out; 1303 } 1304 1305 if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) { 1306 switch(hw->phy.media_type) { 1307 case e1000_media_type_internal_serdes: 1308 *data = ID_LED_DEFAULT_82575_SERDES; 1309 break; 1310 case e1000_media_type_copper: 1311 default: 1312 *data = ID_LED_DEFAULT; 1313 break; 1314 } 1315 } 1316out: 1317 return ret_val; 1318} 1319 1320/** 1321 * igb_id_led_init - 1322 * @hw: pointer to the HW structure 1323 * 1324 **/ 1325s32 igb_id_led_init(struct e1000_hw *hw) 1326{ 1327 struct e1000_mac_info *mac = &hw->mac; 1328 s32 ret_val; 1329 const u32 ledctl_mask = 0x000000FF; 1330 const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON; 1331 const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF; 1332 u16 data, i, temp; 1333 const u16 led_mask = 0x0F; 1334 1335 ret_val = igb_valid_led_default(hw, &data); 1336 if (ret_val) 1337 goto out; 1338 1339 mac->ledctl_default = rd32(E1000_LEDCTL); 1340 mac->ledctl_mode1 = mac->ledctl_default; 1341 mac->ledctl_mode2 = mac->ledctl_default; 1342 1343 for (i = 0; i < 4; i++) { 1344 temp = (data >> (i << 2)) & led_mask; 1345 switch (temp) { 1346 case ID_LED_ON1_DEF2: 1347 case ID_LED_ON1_ON2: 1348 case ID_LED_ON1_OFF2: 1349 mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); 1350 mac->ledctl_mode1 |= ledctl_on << (i << 3); 1351 break; 1352 case ID_LED_OFF1_DEF2: 1353 case ID_LED_OFF1_ON2: 1354 case ID_LED_OFF1_OFF2: 1355 mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); 1356 mac->ledctl_mode1 |= ledctl_off << (i << 3); 1357 break; 1358 default: 1359 /* Do nothing */ 1360 break; 1361 } 1362 switch (temp) { 1363 case ID_LED_DEF1_ON2: 1364 case ID_LED_ON1_ON2: 1365 case ID_LED_OFF1_ON2: 1366 mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); 1367 mac->ledctl_mode2 |= ledctl_on << (i << 3); 1368 break; 1369 case ID_LED_DEF1_OFF2: 1370 case ID_LED_ON1_OFF2: 1371 case ID_LED_OFF1_OFF2: 1372 mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); 1373 mac->ledctl_mode2 |= ledctl_off << (i << 3); 1374 break; 1375 default: 1376 /* Do nothing */ 1377 break; 1378 } 1379 } 1380 1381out: 1382 return ret_val; 1383} 1384 1385/** 1386 * igb_cleanup_led - Set LED config to default operation 1387 * @hw: pointer to the HW structure 1388 * 1389 * Remove the current LED configuration and set the LED configuration 1390 * to the default value, saved from the EEPROM. 1391 **/ 1392s32 igb_cleanup_led(struct e1000_hw *hw) 1393{ 1394 wr32(E1000_LEDCTL, hw->mac.ledctl_default); 1395 return 0; 1396} 1397 1398/** 1399 * igb_blink_led - Blink LED 1400 * @hw: pointer to the HW structure 1401 * 1402 * Blink the led's which are set to be on. 1403 **/ 1404s32 igb_blink_led(struct e1000_hw *hw) 1405{ 1406 u32 ledctl_blink = 0; 1407 u32 i; 1408 1409 if (hw->phy.media_type == e1000_media_type_fiber) { 1410 /* always blink LED0 for PCI-E fiber */ 1411 ledctl_blink = E1000_LEDCTL_LED0_BLINK | 1412 (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT); 1413 } else { 1414 /* Set the blink bit for each LED that's "on" (0x0E) 1415 * (or "off" if inverted) in ledctl_mode2. The blink 1416 * logic in hardware only works when mode is set to "on" 1417 * so it must be changed accordingly when the mode is 1418 * "off" and inverted. 1419 */ 1420 ledctl_blink = hw->mac.ledctl_mode2; 1421 for (i = 0; i < 32; i += 8) { 1422 u32 mode = (hw->mac.ledctl_mode2 >> i) & 1423 E1000_LEDCTL_LED0_MODE_MASK; 1424 u32 led_default = hw->mac.ledctl_default >> i; 1425 1426 if ((!(led_default & E1000_LEDCTL_LED0_IVRT) && 1427 (mode == E1000_LEDCTL_MODE_LED_ON)) || 1428 ((led_default & E1000_LEDCTL_LED0_IVRT) && 1429 (mode == E1000_LEDCTL_MODE_LED_OFF))) { 1430 ledctl_blink &= 1431 ~(E1000_LEDCTL_LED0_MODE_MASK << i); 1432 ledctl_blink |= (E1000_LEDCTL_LED0_BLINK | 1433 E1000_LEDCTL_MODE_LED_ON) << i; 1434 } 1435 } 1436 } 1437 1438 wr32(E1000_LEDCTL, ledctl_blink); 1439 1440 return 0; 1441} 1442 1443/** 1444 * igb_led_off - Turn LED off 1445 * @hw: pointer to the HW structure 1446 * 1447 * Turn LED off. 1448 **/ 1449s32 igb_led_off(struct e1000_hw *hw) 1450{ 1451 switch (hw->phy.media_type) { 1452 case e1000_media_type_copper: 1453 wr32(E1000_LEDCTL, hw->mac.ledctl_mode1); 1454 break; 1455 default: 1456 break; 1457 } 1458 1459 return 0; 1460} 1461 1462/** 1463 * igb_disable_pcie_master - Disables PCI-express master access 1464 * @hw: pointer to the HW structure 1465 * 1466 * Returns 0 (0) if successful, else returns -10 1467 * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused 1468 * the master requests to be disabled. 1469 * 1470 * Disables PCI-Express master access and verifies there are no pending 1471 * requests. 1472 **/ 1473s32 igb_disable_pcie_master(struct e1000_hw *hw) 1474{ 1475 u32 ctrl; 1476 s32 timeout = MASTER_DISABLE_TIMEOUT; 1477 s32 ret_val = 0; 1478 1479 if (hw->bus.type != e1000_bus_type_pci_express) 1480 goto out; 1481 1482 ctrl = rd32(E1000_CTRL); 1483 ctrl |= E1000_CTRL_GIO_MASTER_DISABLE; 1484 wr32(E1000_CTRL, ctrl); 1485 1486 while (timeout) { 1487 if (!(rd32(E1000_STATUS) & 1488 E1000_STATUS_GIO_MASTER_ENABLE)) 1489 break; 1490 udelay(100); 1491 timeout--; 1492 } 1493 1494 if (!timeout) { 1495 hw_dbg("Master requests are pending.\n"); 1496 ret_val = -E1000_ERR_MASTER_REQUESTS_PENDING; 1497 goto out; 1498 } 1499 1500out: 1501 return ret_val; 1502} 1503 1504/** 1505 * igb_validate_mdi_setting - Verify MDI/MDIx settings 1506 * @hw: pointer to the HW structure 1507 * 1508 * Verify that when not using auto-negotitation that MDI/MDIx is correctly 1509 * set, which is forced to MDI mode only. 1510 **/ 1511s32 igb_validate_mdi_setting(struct e1000_hw *hw) 1512{ 1513 s32 ret_val = 0; 1514 1515 /* All MDI settings are supported on 82580 and newer. */ 1516 if (hw->mac.type >= e1000_82580) 1517 goto out; 1518 1519 if (!hw->mac.autoneg && (hw->phy.mdix == 0 || hw->phy.mdix == 3)) { 1520 hw_dbg("Invalid MDI setting detected\n"); 1521 hw->phy.mdix = 1; 1522 ret_val = -E1000_ERR_CONFIG; 1523 goto out; 1524 } 1525 1526out: 1527 return ret_val; 1528} 1529 1530/** 1531 * igb_write_8bit_ctrl_reg - Write a 8bit CTRL register 1532 * @hw: pointer to the HW structure 1533 * @reg: 32bit register offset such as E1000_SCTL 1534 * @offset: register offset to write to 1535 * @data: data to write at register offset 1536 * 1537 * Writes an address/data control type register. There are several of these 1538 * and they all have the format address << 8 | data and bit 31 is polled for 1539 * completion. 1540 **/ 1541s32 igb_write_8bit_ctrl_reg(struct e1000_hw *hw, u32 reg, 1542 u32 offset, u8 data) 1543{ 1544 u32 i, regvalue = 0; 1545 s32 ret_val = 0; 1546 1547 /* Set up the address and data */ 1548 regvalue = ((u32)data) | (offset << E1000_GEN_CTL_ADDRESS_SHIFT); 1549 wr32(reg, regvalue); 1550 1551 /* Poll the ready bit to see if the MDI read completed */ 1552 for (i = 0; i < E1000_GEN_POLL_TIMEOUT; i++) { 1553 udelay(5); 1554 regvalue = rd32(reg); 1555 if (regvalue & E1000_GEN_CTL_READY) 1556 break; 1557 } 1558 if (!(regvalue & E1000_GEN_CTL_READY)) { 1559 hw_dbg("Reg %08x did not indicate ready\n", reg); 1560 ret_val = -E1000_ERR_PHY; 1561 goto out; 1562 } 1563 1564out: 1565 return ret_val; 1566} 1567 1568/** 1569 * igb_enable_mng_pass_thru - Enable processing of ARP's 1570 * @hw: pointer to the HW structure 1571 * 1572 * Verifies the hardware needs to leave interface enabled so that frames can 1573 * be directed to and from the management interface. 1574 **/ 1575bool igb_enable_mng_pass_thru(struct e1000_hw *hw) 1576{ 1577 u32 manc; 1578 u32 fwsm, factps; 1579 bool ret_val = false; 1580 1581 if (!hw->mac.asf_firmware_present) 1582 goto out; 1583 1584 manc = rd32(E1000_MANC); 1585 1586 if (!(manc & E1000_MANC_RCV_TCO_EN)) 1587 goto out; 1588 1589 if (hw->mac.arc_subsystem_valid) { 1590 fwsm = rd32(E1000_FWSM); 1591 factps = rd32(E1000_FACTPS); 1592 1593 if (!(factps & E1000_FACTPS_MNGCG) && 1594 ((fwsm & E1000_FWSM_MODE_MASK) == 1595 (e1000_mng_mode_pt << E1000_FWSM_MODE_SHIFT))) { 1596 ret_val = true; 1597 goto out; 1598 } 1599 } else { 1600 if ((manc & E1000_MANC_SMBUS_EN) && 1601 !(manc & E1000_MANC_ASF_EN)) { 1602 ret_val = true; 1603 goto out; 1604 } 1605 } 1606 1607out: 1608 return ret_val; 1609} 1610