phy.c revision 1063b176c072b936c43d0e6270168b19881ecb72
1/* 2 * PHY functions 3 * 4 * Copyright (c) 2004-2007 Reyk Floeter <reyk@openbsd.org> 5 * Copyright (c) 2006-2009 Nick Kossifidis <mickflemm@gmail.com> 6 * Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com> 7 * Copyright (c) 2008-2009 Felix Fietkau <nbd@openwrt.org> 8 * 9 * Permission to use, copy, modify, and distribute this software for any 10 * purpose with or without fee is hereby granted, provided that the above 11 * copyright notice and this permission notice appear in all copies. 12 * 13 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES 14 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF 15 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR 16 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES 17 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN 18 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF 19 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. 20 * 21 */ 22 23#include <linux/delay.h> 24 25#include "ath5k.h" 26#include "reg.h" 27#include "base.h" 28#include "rfbuffer.h" 29#include "rfgain.h" 30 31/* 32 * Used to modify RF Banks before writing them to AR5K_RF_BUFFER 33 */ 34static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah, 35 const struct ath5k_rf_reg *rf_regs, 36 u32 val, u8 reg_id, bool set) 37{ 38 const struct ath5k_rf_reg *rfreg = NULL; 39 u8 offset, bank, num_bits, col, position; 40 u16 entry; 41 u32 mask, data, last_bit, bits_shifted, first_bit; 42 u32 *rfb; 43 s32 bits_left; 44 int i; 45 46 data = 0; 47 rfb = ah->ah_rf_banks; 48 49 for (i = 0; i < ah->ah_rf_regs_count; i++) { 50 if (rf_regs[i].index == reg_id) { 51 rfreg = &rf_regs[i]; 52 break; 53 } 54 } 55 56 if (rfb == NULL || rfreg == NULL) { 57 ATH5K_PRINTF("Rf register not found!\n"); 58 /* should not happen */ 59 return 0; 60 } 61 62 bank = rfreg->bank; 63 num_bits = rfreg->field.len; 64 first_bit = rfreg->field.pos; 65 col = rfreg->field.col; 66 67 /* first_bit is an offset from bank's 68 * start. Since we have all banks on 69 * the same array, we use this offset 70 * to mark each bank's start */ 71 offset = ah->ah_offset[bank]; 72 73 /* Boundary check */ 74 if (!(col <= 3 && num_bits <= 32 && first_bit + num_bits <= 319)) { 75 ATH5K_PRINTF("invalid values at offset %u\n", offset); 76 return 0; 77 } 78 79 entry = ((first_bit - 1) / 8) + offset; 80 position = (first_bit - 1) % 8; 81 82 if (set) 83 data = ath5k_hw_bitswap(val, num_bits); 84 85 for (bits_shifted = 0, bits_left = num_bits; bits_left > 0; 86 position = 0, entry++) { 87 88 last_bit = (position + bits_left > 8) ? 8 : 89 position + bits_left; 90 91 mask = (((1 << last_bit) - 1) ^ ((1 << position) - 1)) << 92 (col * 8); 93 94 if (set) { 95 rfb[entry] &= ~mask; 96 rfb[entry] |= ((data << position) << (col * 8)) & mask; 97 data >>= (8 - position); 98 } else { 99 data |= (((rfb[entry] & mask) >> (col * 8)) >> position) 100 << bits_shifted; 101 bits_shifted += last_bit - position; 102 } 103 104 bits_left -= 8 - position; 105 } 106 107 data = set ? 1 : ath5k_hw_bitswap(data, num_bits); 108 109 return data; 110} 111 112/**********************\ 113* RF Gain optimization * 114\**********************/ 115 116/* 117 * This code is used to optimize rf gain on different environments 118 * (temperature mostly) based on feedback from a power detector. 119 * 120 * It's only used on RF5111 and RF5112, later RF chips seem to have 121 * auto adjustment on hw -notice they have a much smaller BANK 7 and 122 * no gain optimization ladder-. 123 * 124 * For more infos check out this patent doc 125 * http://www.freepatentsonline.com/7400691.html 126 * 127 * This paper describes power drops as seen on the receiver due to 128 * probe packets 129 * http://www.cnri.dit.ie/publications/ICT08%20-%20Practical%20Issues 130 * %20of%20Power%20Control.pdf 131 * 132 * And this is the MadWiFi bug entry related to the above 133 * http://madwifi-project.org/ticket/1659 134 * with various measurements and diagrams 135 * 136 * TODO: Deal with power drops due to probes by setting an apropriate 137 * tx power on the probe packets ! Make this part of the calibration process. 138 */ 139 140/* Initialize ah_gain durring attach */ 141int ath5k_hw_rfgain_opt_init(struct ath5k_hw *ah) 142{ 143 /* Initialize the gain optimization values */ 144 switch (ah->ah_radio) { 145 case AR5K_RF5111: 146 ah->ah_gain.g_step_idx = rfgain_opt_5111.go_default; 147 ah->ah_gain.g_low = 20; 148 ah->ah_gain.g_high = 35; 149 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 150 break; 151 case AR5K_RF5112: 152 ah->ah_gain.g_step_idx = rfgain_opt_5112.go_default; 153 ah->ah_gain.g_low = 20; 154 ah->ah_gain.g_high = 85; 155 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 156 break; 157 default: 158 return -EINVAL; 159 } 160 161 return 0; 162} 163 164/* Schedule a gain probe check on the next transmited packet. 165 * That means our next packet is going to be sent with lower 166 * tx power and a Peak to Average Power Detector (PAPD) will try 167 * to measure the gain. 168 * 169 * XXX: How about forcing a tx packet (bypassing PCU arbitrator etc) 170 * just after we enable the probe so that we don't mess with 171 * standard traffic ? Maybe it's time to use sw interrupts and 172 * a probe tasklet !!! 173 */ 174static void ath5k_hw_request_rfgain_probe(struct ath5k_hw *ah) 175{ 176 177 /* Skip if gain calibration is inactive or 178 * we already handle a probe request */ 179 if (ah->ah_gain.g_state != AR5K_RFGAIN_ACTIVE) 180 return; 181 182 /* Send the packet with 2dB below max power as 183 * patent doc suggest */ 184 ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txpower.txp_ofdm - 4, 185 AR5K_PHY_PAPD_PROBE_TXPOWER) | 186 AR5K_PHY_PAPD_PROBE_TX_NEXT, AR5K_PHY_PAPD_PROBE); 187 188 ah->ah_gain.g_state = AR5K_RFGAIN_READ_REQUESTED; 189 190} 191 192/* Calculate gain_F measurement correction 193 * based on the current step for RF5112 rev. 2 */ 194static u32 ath5k_hw_rf_gainf_corr(struct ath5k_hw *ah) 195{ 196 u32 mix, step; 197 u32 *rf; 198 const struct ath5k_gain_opt *go; 199 const struct ath5k_gain_opt_step *g_step; 200 const struct ath5k_rf_reg *rf_regs; 201 202 /* Only RF5112 Rev. 2 supports it */ 203 if ((ah->ah_radio != AR5K_RF5112) || 204 (ah->ah_radio_5ghz_revision <= AR5K_SREV_RAD_5112A)) 205 return 0; 206 207 go = &rfgain_opt_5112; 208 rf_regs = rf_regs_5112a; 209 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a); 210 211 g_step = &go->go_step[ah->ah_gain.g_step_idx]; 212 213 if (ah->ah_rf_banks == NULL) 214 return 0; 215 216 rf = ah->ah_rf_banks; 217 ah->ah_gain.g_f_corr = 0; 218 219 /* No VGA (Variable Gain Amplifier) override, skip */ 220 if (ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, false) != 1) 221 return 0; 222 223 /* Mix gain stepping */ 224 step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXGAIN_STEP, false); 225 226 /* Mix gain override */ 227 mix = g_step->gos_param[0]; 228 229 switch (mix) { 230 case 3: 231 ah->ah_gain.g_f_corr = step * 2; 232 break; 233 case 2: 234 ah->ah_gain.g_f_corr = (step - 5) * 2; 235 break; 236 case 1: 237 ah->ah_gain.g_f_corr = step; 238 break; 239 default: 240 ah->ah_gain.g_f_corr = 0; 241 break; 242 } 243 244 return ah->ah_gain.g_f_corr; 245} 246 247/* Check if current gain_F measurement is in the range of our 248 * power detector windows. If we get a measurement outside range 249 * we know it's not accurate (detectors can't measure anything outside 250 * their detection window) so we must ignore it */ 251static bool ath5k_hw_rf_check_gainf_readback(struct ath5k_hw *ah) 252{ 253 const struct ath5k_rf_reg *rf_regs; 254 u32 step, mix_ovr, level[4]; 255 u32 *rf; 256 257 if (ah->ah_rf_banks == NULL) 258 return false; 259 260 rf = ah->ah_rf_banks; 261 262 if (ah->ah_radio == AR5K_RF5111) { 263 264 rf_regs = rf_regs_5111; 265 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111); 266 267 step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_RFGAIN_STEP, 268 false); 269 270 level[0] = 0; 271 level[1] = (step == 63) ? 50 : step + 4; 272 level[2] = (step != 63) ? 64 : level[0]; 273 level[3] = level[2] + 50 ; 274 275 ah->ah_gain.g_high = level[3] - 276 (step == 63 ? AR5K_GAIN_DYN_ADJUST_HI_MARGIN : -5); 277 ah->ah_gain.g_low = level[0] + 278 (step == 63 ? AR5K_GAIN_DYN_ADJUST_LO_MARGIN : 0); 279 } else { 280 281 rf_regs = rf_regs_5112; 282 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112); 283 284 mix_ovr = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, 285 false); 286 287 level[0] = level[2] = 0; 288 289 if (mix_ovr == 1) { 290 level[1] = level[3] = 83; 291 } else { 292 level[1] = level[3] = 107; 293 ah->ah_gain.g_high = 55; 294 } 295 } 296 297 return (ah->ah_gain.g_current >= level[0] && 298 ah->ah_gain.g_current <= level[1]) || 299 (ah->ah_gain.g_current >= level[2] && 300 ah->ah_gain.g_current <= level[3]); 301} 302 303/* Perform gain_F adjustment by choosing the right set 304 * of parameters from rf gain optimization ladder */ 305static s8 ath5k_hw_rf_gainf_adjust(struct ath5k_hw *ah) 306{ 307 const struct ath5k_gain_opt *go; 308 const struct ath5k_gain_opt_step *g_step; 309 int ret = 0; 310 311 switch (ah->ah_radio) { 312 case AR5K_RF5111: 313 go = &rfgain_opt_5111; 314 break; 315 case AR5K_RF5112: 316 go = &rfgain_opt_5112; 317 break; 318 default: 319 return 0; 320 } 321 322 g_step = &go->go_step[ah->ah_gain.g_step_idx]; 323 324 if (ah->ah_gain.g_current >= ah->ah_gain.g_high) { 325 326 /* Reached maximum */ 327 if (ah->ah_gain.g_step_idx == 0) 328 return -1; 329 330 for (ah->ah_gain.g_target = ah->ah_gain.g_current; 331 ah->ah_gain.g_target >= ah->ah_gain.g_high && 332 ah->ah_gain.g_step_idx > 0; 333 g_step = &go->go_step[ah->ah_gain.g_step_idx]) 334 ah->ah_gain.g_target -= 2 * 335 (go->go_step[--(ah->ah_gain.g_step_idx)].gos_gain - 336 g_step->gos_gain); 337 338 ret = 1; 339 goto done; 340 } 341 342 if (ah->ah_gain.g_current <= ah->ah_gain.g_low) { 343 344 /* Reached minimum */ 345 if (ah->ah_gain.g_step_idx == (go->go_steps_count - 1)) 346 return -2; 347 348 for (ah->ah_gain.g_target = ah->ah_gain.g_current; 349 ah->ah_gain.g_target <= ah->ah_gain.g_low && 350 ah->ah_gain.g_step_idx < go->go_steps_count-1; 351 g_step = &go->go_step[ah->ah_gain.g_step_idx]) 352 ah->ah_gain.g_target -= 2 * 353 (go->go_step[++ah->ah_gain.g_step_idx].gos_gain - 354 g_step->gos_gain); 355 356 ret = 2; 357 goto done; 358 } 359 360done: 361 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 362 "ret %d, gain step %u, current gain %u, target gain %u\n", 363 ret, ah->ah_gain.g_step_idx, ah->ah_gain.g_current, 364 ah->ah_gain.g_target); 365 366 return ret; 367} 368 369/* Main callback for thermal rf gain calibration engine 370 * Check for a new gain reading and schedule an adjustment 371 * if needed. 372 * 373 * TODO: Use sw interrupt to schedule reset if gain_F needs 374 * adjustment */ 375enum ath5k_rfgain ath5k_hw_gainf_calibrate(struct ath5k_hw *ah) 376{ 377 u32 data, type; 378 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 379 380 ATH5K_TRACE(ah->ah_sc); 381 382 if (ah->ah_rf_banks == NULL || 383 ah->ah_gain.g_state == AR5K_RFGAIN_INACTIVE) 384 return AR5K_RFGAIN_INACTIVE; 385 386 /* No check requested, either engine is inactive 387 * or an adjustment is already requested */ 388 if (ah->ah_gain.g_state != AR5K_RFGAIN_READ_REQUESTED) 389 goto done; 390 391 /* Read the PAPD (Peak to Average Power Detector) 392 * register */ 393 data = ath5k_hw_reg_read(ah, AR5K_PHY_PAPD_PROBE); 394 395 /* No probe is scheduled, read gain_F measurement */ 396 if (!(data & AR5K_PHY_PAPD_PROBE_TX_NEXT)) { 397 ah->ah_gain.g_current = data >> AR5K_PHY_PAPD_PROBE_GAINF_S; 398 type = AR5K_REG_MS(data, AR5K_PHY_PAPD_PROBE_TYPE); 399 400 /* If tx packet is CCK correct the gain_F measurement 401 * by cck ofdm gain delta */ 402 if (type == AR5K_PHY_PAPD_PROBE_TYPE_CCK) { 403 if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) 404 ah->ah_gain.g_current += 405 ee->ee_cck_ofdm_gain_delta; 406 else 407 ah->ah_gain.g_current += 408 AR5K_GAIN_CCK_PROBE_CORR; 409 } 410 411 /* Further correct gain_F measurement for 412 * RF5112A radios */ 413 if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) { 414 ath5k_hw_rf_gainf_corr(ah); 415 ah->ah_gain.g_current = 416 ah->ah_gain.g_current >= ah->ah_gain.g_f_corr ? 417 (ah->ah_gain.g_current-ah->ah_gain.g_f_corr) : 418 0; 419 } 420 421 /* Check if measurement is ok and if we need 422 * to adjust gain, schedule a gain adjustment, 423 * else switch back to the acive state */ 424 if (ath5k_hw_rf_check_gainf_readback(ah) && 425 AR5K_GAIN_CHECK_ADJUST(&ah->ah_gain) && 426 ath5k_hw_rf_gainf_adjust(ah)) { 427 ah->ah_gain.g_state = AR5K_RFGAIN_NEED_CHANGE; 428 } else { 429 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 430 } 431 } 432 433done: 434 return ah->ah_gain.g_state; 435} 436 437/* Write initial rf gain table to set the RF sensitivity 438 * this one works on all RF chips and has nothing to do 439 * with gain_F calibration */ 440int ath5k_hw_rfgain_init(struct ath5k_hw *ah, unsigned int freq) 441{ 442 const struct ath5k_ini_rfgain *ath5k_rfg; 443 unsigned int i, size; 444 445 switch (ah->ah_radio) { 446 case AR5K_RF5111: 447 ath5k_rfg = rfgain_5111; 448 size = ARRAY_SIZE(rfgain_5111); 449 break; 450 case AR5K_RF5112: 451 ath5k_rfg = rfgain_5112; 452 size = ARRAY_SIZE(rfgain_5112); 453 break; 454 case AR5K_RF2413: 455 ath5k_rfg = rfgain_2413; 456 size = ARRAY_SIZE(rfgain_2413); 457 break; 458 case AR5K_RF2316: 459 ath5k_rfg = rfgain_2316; 460 size = ARRAY_SIZE(rfgain_2316); 461 break; 462 case AR5K_RF5413: 463 ath5k_rfg = rfgain_5413; 464 size = ARRAY_SIZE(rfgain_5413); 465 break; 466 case AR5K_RF2317: 467 case AR5K_RF2425: 468 ath5k_rfg = rfgain_2425; 469 size = ARRAY_SIZE(rfgain_2425); 470 break; 471 default: 472 return -EINVAL; 473 } 474 475 switch (freq) { 476 case AR5K_INI_RFGAIN_2GHZ: 477 case AR5K_INI_RFGAIN_5GHZ: 478 break; 479 default: 480 return -EINVAL; 481 } 482 483 for (i = 0; i < size; i++) { 484 AR5K_REG_WAIT(i); 485 ath5k_hw_reg_write(ah, ath5k_rfg[i].rfg_value[freq], 486 (u32)ath5k_rfg[i].rfg_register); 487 } 488 489 return 0; 490} 491 492 493 494/********************\ 495* RF Registers setup * 496\********************/ 497 498 499/* 500 * Setup RF registers by writing rf buffer on hw 501 */ 502int ath5k_hw_rfregs_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, 503 unsigned int mode) 504{ 505 const struct ath5k_rf_reg *rf_regs; 506 const struct ath5k_ini_rfbuffer *ini_rfb; 507 const struct ath5k_gain_opt *go = NULL; 508 const struct ath5k_gain_opt_step *g_step; 509 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 510 u8 ee_mode = 0; 511 u32 *rfb; 512 int i, obdb = -1, bank = -1; 513 514 switch (ah->ah_radio) { 515 case AR5K_RF5111: 516 rf_regs = rf_regs_5111; 517 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111); 518 ini_rfb = rfb_5111; 519 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5111); 520 go = &rfgain_opt_5111; 521 break; 522 case AR5K_RF5112: 523 if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) { 524 rf_regs = rf_regs_5112a; 525 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a); 526 ini_rfb = rfb_5112a; 527 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112a); 528 } else { 529 rf_regs = rf_regs_5112; 530 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112); 531 ini_rfb = rfb_5112; 532 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112); 533 } 534 go = &rfgain_opt_5112; 535 break; 536 case AR5K_RF2413: 537 rf_regs = rf_regs_2413; 538 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2413); 539 ini_rfb = rfb_2413; 540 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2413); 541 break; 542 case AR5K_RF2316: 543 rf_regs = rf_regs_2316; 544 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2316); 545 ini_rfb = rfb_2316; 546 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2316); 547 break; 548 case AR5K_RF5413: 549 rf_regs = rf_regs_5413; 550 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5413); 551 ini_rfb = rfb_5413; 552 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5413); 553 break; 554 case AR5K_RF2317: 555 rf_regs = rf_regs_2425; 556 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425); 557 ini_rfb = rfb_2317; 558 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2317); 559 break; 560 case AR5K_RF2425: 561 rf_regs = rf_regs_2425; 562 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425); 563 if (ah->ah_mac_srev < AR5K_SREV_AR2417) { 564 ini_rfb = rfb_2425; 565 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2425); 566 } else { 567 ini_rfb = rfb_2417; 568 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2417); 569 } 570 break; 571 default: 572 return -EINVAL; 573 } 574 575 /* If it's the first time we set rf buffer, allocate 576 * ah->ah_rf_banks based on ah->ah_rf_banks_size 577 * we set above */ 578 if (ah->ah_rf_banks == NULL) { 579 ah->ah_rf_banks = kmalloc(sizeof(u32) * ah->ah_rf_banks_size, 580 GFP_KERNEL); 581 if (ah->ah_rf_banks == NULL) { 582 ATH5K_ERR(ah->ah_sc, "out of memory\n"); 583 return -ENOMEM; 584 } 585 } 586 587 /* Copy values to modify them */ 588 rfb = ah->ah_rf_banks; 589 590 for (i = 0; i < ah->ah_rf_banks_size; i++) { 591 if (ini_rfb[i].rfb_bank >= AR5K_MAX_RF_BANKS) { 592 ATH5K_ERR(ah->ah_sc, "invalid bank\n"); 593 return -EINVAL; 594 } 595 596 /* Bank changed, write down the offset */ 597 if (bank != ini_rfb[i].rfb_bank) { 598 bank = ini_rfb[i].rfb_bank; 599 ah->ah_offset[bank] = i; 600 } 601 602 rfb[i] = ini_rfb[i].rfb_mode_data[mode]; 603 } 604 605 /* Set Output and Driver bias current (OB/DB) */ 606 if (channel->hw_value & CHANNEL_2GHZ) { 607 608 if (channel->hw_value & CHANNEL_CCK) 609 ee_mode = AR5K_EEPROM_MODE_11B; 610 else 611 ee_mode = AR5K_EEPROM_MODE_11G; 612 613 /* For RF511X/RF211X combination we 614 * use b_OB and b_DB parameters stored 615 * in eeprom on ee->ee_ob[ee_mode][0] 616 * 617 * For all other chips we use OB/DB for 2Ghz 618 * stored in the b/g modal section just like 619 * 802.11a on ee->ee_ob[ee_mode][1] */ 620 if ((ah->ah_radio == AR5K_RF5111) || 621 (ah->ah_radio == AR5K_RF5112)) 622 obdb = 0; 623 else 624 obdb = 1; 625 626 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb], 627 AR5K_RF_OB_2GHZ, true); 628 629 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb], 630 AR5K_RF_DB_2GHZ, true); 631 632 /* RF5111 always needs OB/DB for 5GHz, even if we use 2GHz */ 633 } else if ((channel->hw_value & CHANNEL_5GHZ) || 634 (ah->ah_radio == AR5K_RF5111)) { 635 636 /* For 11a, Turbo and XR we need to choose 637 * OB/DB based on frequency range */ 638 ee_mode = AR5K_EEPROM_MODE_11A; 639 obdb = channel->center_freq >= 5725 ? 3 : 640 (channel->center_freq >= 5500 ? 2 : 641 (channel->center_freq >= 5260 ? 1 : 642 (channel->center_freq > 4000 ? 0 : -1))); 643 644 if (obdb < 0) 645 return -EINVAL; 646 647 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb], 648 AR5K_RF_OB_5GHZ, true); 649 650 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb], 651 AR5K_RF_DB_5GHZ, true); 652 } 653 654 g_step = &go->go_step[ah->ah_gain.g_step_idx]; 655 656 /* Bank Modifications (chip-specific) */ 657 if (ah->ah_radio == AR5K_RF5111) { 658 659 /* Set gain_F settings according to current step */ 660 if (channel->hw_value & CHANNEL_OFDM) { 661 662 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_FRAME_CTL, 663 AR5K_PHY_FRAME_CTL_TX_CLIP, 664 g_step->gos_param[0]); 665 666 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1], 667 AR5K_RF_PWD_90, true); 668 669 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2], 670 AR5K_RF_PWD_84, true); 671 672 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3], 673 AR5K_RF_RFGAIN_SEL, true); 674 675 /* We programmed gain_F parameters, switch back 676 * to active state */ 677 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 678 679 } 680 681 /* Bank 6/7 setup */ 682 683 ath5k_hw_rfb_op(ah, rf_regs, !ee->ee_xpd[ee_mode], 684 AR5K_RF_PWD_XPD, true); 685 686 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_x_gain[ee_mode], 687 AR5K_RF_XPD_GAIN, true); 688 689 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode], 690 AR5K_RF_GAIN_I, true); 691 692 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode], 693 AR5K_RF_PLO_SEL, true); 694 695 /* TODO: Half/quarter channel support */ 696 } 697 698 if (ah->ah_radio == AR5K_RF5112) { 699 700 /* Set gain_F settings according to current step */ 701 if (channel->hw_value & CHANNEL_OFDM) { 702 703 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[0], 704 AR5K_RF_MIXGAIN_OVR, true); 705 706 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1], 707 AR5K_RF_PWD_138, true); 708 709 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2], 710 AR5K_RF_PWD_137, true); 711 712 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3], 713 AR5K_RF_PWD_136, true); 714 715 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[4], 716 AR5K_RF_PWD_132, true); 717 718 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[5], 719 AR5K_RF_PWD_131, true); 720 721 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[6], 722 AR5K_RF_PWD_130, true); 723 724 /* We programmed gain_F parameters, switch back 725 * to active state */ 726 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 727 } 728 729 /* Bank 6/7 setup */ 730 731 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode], 732 AR5K_RF_XPD_SEL, true); 733 734 if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112A) { 735 /* Rev. 1 supports only one xpd */ 736 ath5k_hw_rfb_op(ah, rf_regs, 737 ee->ee_x_gain[ee_mode], 738 AR5K_RF_XPD_GAIN, true); 739 740 } else { 741 u8 *pdg_curve_to_idx = ee->ee_pdc_to_idx[ee_mode]; 742 if (ee->ee_pd_gains[ee_mode] > 1) { 743 ath5k_hw_rfb_op(ah, rf_regs, 744 pdg_curve_to_idx[0], 745 AR5K_RF_PD_GAIN_LO, true); 746 ath5k_hw_rfb_op(ah, rf_regs, 747 pdg_curve_to_idx[1], 748 AR5K_RF_PD_GAIN_HI, true); 749 } else { 750 ath5k_hw_rfb_op(ah, rf_regs, 751 pdg_curve_to_idx[0], 752 AR5K_RF_PD_GAIN_LO, true); 753 ath5k_hw_rfb_op(ah, rf_regs, 754 pdg_curve_to_idx[0], 755 AR5K_RF_PD_GAIN_HI, true); 756 } 757 758 /* Lower synth voltage on Rev 2 */ 759 ath5k_hw_rfb_op(ah, rf_regs, 2, 760 AR5K_RF_HIGH_VC_CP, true); 761 762 ath5k_hw_rfb_op(ah, rf_regs, 2, 763 AR5K_RF_MID_VC_CP, true); 764 765 ath5k_hw_rfb_op(ah, rf_regs, 2, 766 AR5K_RF_LOW_VC_CP, true); 767 768 ath5k_hw_rfb_op(ah, rf_regs, 2, 769 AR5K_RF_PUSH_UP, true); 770 771 /* Decrease power consumption on 5213+ BaseBand */ 772 if (ah->ah_phy_revision >= AR5K_SREV_PHY_5212A) { 773 ath5k_hw_rfb_op(ah, rf_regs, 1, 774 AR5K_RF_PAD2GND, true); 775 776 ath5k_hw_rfb_op(ah, rf_regs, 1, 777 AR5K_RF_XB2_LVL, true); 778 779 ath5k_hw_rfb_op(ah, rf_regs, 1, 780 AR5K_RF_XB5_LVL, true); 781 782 ath5k_hw_rfb_op(ah, rf_regs, 1, 783 AR5K_RF_PWD_167, true); 784 785 ath5k_hw_rfb_op(ah, rf_regs, 1, 786 AR5K_RF_PWD_166, true); 787 } 788 } 789 790 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode], 791 AR5K_RF_GAIN_I, true); 792 793 /* TODO: Half/quarter channel support */ 794 795 } 796 797 if (ah->ah_radio == AR5K_RF5413 && 798 channel->hw_value & CHANNEL_2GHZ) { 799 800 ath5k_hw_rfb_op(ah, rf_regs, 1, AR5K_RF_DERBY_CHAN_SEL_MODE, 801 true); 802 803 /* Set optimum value for early revisions (on pci-e chips) */ 804 if (ah->ah_mac_srev >= AR5K_SREV_AR5424 && 805 ah->ah_mac_srev < AR5K_SREV_AR5413) 806 ath5k_hw_rfb_op(ah, rf_regs, ath5k_hw_bitswap(6, 3), 807 AR5K_RF_PWD_ICLOBUF_2G, true); 808 809 } 810 811 /* Write RF banks on hw */ 812 for (i = 0; i < ah->ah_rf_banks_size; i++) { 813 AR5K_REG_WAIT(i); 814 ath5k_hw_reg_write(ah, rfb[i], ini_rfb[i].rfb_ctrl_register); 815 } 816 817 return 0; 818} 819 820 821/**************************\ 822 PHY/RF channel functions 823\**************************/ 824 825/* 826 * Check if a channel is supported 827 */ 828bool ath5k_channel_ok(struct ath5k_hw *ah, u16 freq, unsigned int flags) 829{ 830 /* Check if the channel is in our supported range */ 831 if (flags & CHANNEL_2GHZ) { 832 if ((freq >= ah->ah_capabilities.cap_range.range_2ghz_min) && 833 (freq <= ah->ah_capabilities.cap_range.range_2ghz_max)) 834 return true; 835 } else if (flags & CHANNEL_5GHZ) 836 if ((freq >= ah->ah_capabilities.cap_range.range_5ghz_min) && 837 (freq <= ah->ah_capabilities.cap_range.range_5ghz_max)) 838 return true; 839 840 return false; 841} 842 843/* 844 * Convertion needed for RF5110 845 */ 846static u32 ath5k_hw_rf5110_chan2athchan(struct ieee80211_channel *channel) 847{ 848 u32 athchan; 849 850 /* 851 * Convert IEEE channel/MHz to an internal channel value used 852 * by the AR5210 chipset. This has not been verified with 853 * newer chipsets like the AR5212A who have a completely 854 * different RF/PHY part. 855 */ 856 athchan = (ath5k_hw_bitswap( 857 (ieee80211_frequency_to_channel( 858 channel->center_freq) - 24) / 2, 5) 859 << 1) | (1 << 6) | 0x1; 860 return athchan; 861} 862 863/* 864 * Set channel on RF5110 865 */ 866static int ath5k_hw_rf5110_channel(struct ath5k_hw *ah, 867 struct ieee80211_channel *channel) 868{ 869 u32 data; 870 871 /* 872 * Set the channel and wait 873 */ 874 data = ath5k_hw_rf5110_chan2athchan(channel); 875 ath5k_hw_reg_write(ah, data, AR5K_RF_BUFFER); 876 ath5k_hw_reg_write(ah, 0, AR5K_RF_BUFFER_CONTROL_0); 877 mdelay(1); 878 879 return 0; 880} 881 882/* 883 * Convertion needed for 5111 884 */ 885static int ath5k_hw_rf5111_chan2athchan(unsigned int ieee, 886 struct ath5k_athchan_2ghz *athchan) 887{ 888 int channel; 889 890 /* Cast this value to catch negative channel numbers (>= -19) */ 891 channel = (int)ieee; 892 893 /* 894 * Map 2GHz IEEE channel to 5GHz Atheros channel 895 */ 896 if (channel <= 13) { 897 athchan->a2_athchan = 115 + channel; 898 athchan->a2_flags = 0x46; 899 } else if (channel == 14) { 900 athchan->a2_athchan = 124; 901 athchan->a2_flags = 0x44; 902 } else if (channel >= 15 && channel <= 26) { 903 athchan->a2_athchan = ((channel - 14) * 4) + 132; 904 athchan->a2_flags = 0x46; 905 } else 906 return -EINVAL; 907 908 return 0; 909} 910 911/* 912 * Set channel on 5111 913 */ 914static int ath5k_hw_rf5111_channel(struct ath5k_hw *ah, 915 struct ieee80211_channel *channel) 916{ 917 struct ath5k_athchan_2ghz ath5k_channel_2ghz; 918 unsigned int ath5k_channel = 919 ieee80211_frequency_to_channel(channel->center_freq); 920 u32 data0, data1, clock; 921 int ret; 922 923 /* 924 * Set the channel on the RF5111 radio 925 */ 926 data0 = data1 = 0; 927 928 if (channel->hw_value & CHANNEL_2GHZ) { 929 /* Map 2GHz channel to 5GHz Atheros channel ID */ 930 ret = ath5k_hw_rf5111_chan2athchan( 931 ieee80211_frequency_to_channel(channel->center_freq), 932 &ath5k_channel_2ghz); 933 if (ret) 934 return ret; 935 936 ath5k_channel = ath5k_channel_2ghz.a2_athchan; 937 data0 = ((ath5k_hw_bitswap(ath5k_channel_2ghz.a2_flags, 8) & 0xff) 938 << 5) | (1 << 4); 939 } 940 941 if (ath5k_channel < 145 || !(ath5k_channel & 1)) { 942 clock = 1; 943 data1 = ((ath5k_hw_bitswap(ath5k_channel - 24, 8) & 0xff) << 2) | 944 (clock << 1) | (1 << 10) | 1; 945 } else { 946 clock = 0; 947 data1 = ((ath5k_hw_bitswap((ath5k_channel - 24) / 2, 8) & 0xff) 948 << 2) | (clock << 1) | (1 << 10) | 1; 949 } 950 951 ath5k_hw_reg_write(ah, (data1 & 0xff) | ((data0 & 0xff) << 8), 952 AR5K_RF_BUFFER); 953 ath5k_hw_reg_write(ah, ((data1 >> 8) & 0xff) | (data0 & 0xff00), 954 AR5K_RF_BUFFER_CONTROL_3); 955 956 return 0; 957} 958 959/* 960 * Set channel on 5112 and newer 961 */ 962static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah, 963 struct ieee80211_channel *channel) 964{ 965 u32 data, data0, data1, data2; 966 u16 c; 967 968 data = data0 = data1 = data2 = 0; 969 c = channel->center_freq; 970 971 if (c < 4800) { 972 if (!((c - 2224) % 5)) { 973 data0 = ((2 * (c - 704)) - 3040) / 10; 974 data1 = 1; 975 } else if (!((c - 2192) % 5)) { 976 data0 = ((2 * (c - 672)) - 3040) / 10; 977 data1 = 0; 978 } else 979 return -EINVAL; 980 981 data0 = ath5k_hw_bitswap((data0 << 2) & 0xff, 8); 982 } else if ((c - (c % 5)) != 2 || c > 5435) { 983 if (!(c % 20) && c >= 5120) { 984 data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); 985 data2 = ath5k_hw_bitswap(3, 2); 986 } else if (!(c % 10)) { 987 data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); 988 data2 = ath5k_hw_bitswap(2, 2); 989 } else if (!(c % 5)) { 990 data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); 991 data2 = ath5k_hw_bitswap(1, 2); 992 } else 993 return -EINVAL; 994 } else { 995 data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8); 996 data2 = ath5k_hw_bitswap(0, 2); 997 } 998 999 data = (data0 << 4) | (data1 << 1) | (data2 << 2) | 0x1001; 1000 1001 ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); 1002 ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); 1003 1004 return 0; 1005} 1006 1007/* 1008 * Set the channel on the RF2425 1009 */ 1010static int ath5k_hw_rf2425_channel(struct ath5k_hw *ah, 1011 struct ieee80211_channel *channel) 1012{ 1013 u32 data, data0, data2; 1014 u16 c; 1015 1016 data = data0 = data2 = 0; 1017 c = channel->center_freq; 1018 1019 if (c < 4800) { 1020 data0 = ath5k_hw_bitswap((c - 2272), 8); 1021 data2 = 0; 1022 /* ? 5GHz ? */ 1023 } else if ((c - (c % 5)) != 2 || c > 5435) { 1024 if (!(c % 20) && c < 5120) 1025 data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); 1026 else if (!(c % 10)) 1027 data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); 1028 else if (!(c % 5)) 1029 data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); 1030 else 1031 return -EINVAL; 1032 data2 = ath5k_hw_bitswap(1, 2); 1033 } else { 1034 data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8); 1035 data2 = ath5k_hw_bitswap(0, 2); 1036 } 1037 1038 data = (data0 << 4) | data2 << 2 | 0x1001; 1039 1040 ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); 1041 ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); 1042 1043 return 0; 1044} 1045 1046/* 1047 * Set a channel on the radio chip 1048 */ 1049int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel) 1050{ 1051 int ret; 1052 /* 1053 * Check bounds supported by the PHY (we don't care about regultory 1054 * restrictions at this point). Note: hw_value already has the band 1055 * (CHANNEL_2GHZ, or CHANNEL_5GHZ) so we inform ath5k_channel_ok() 1056 * of the band by that */ 1057 if (!ath5k_channel_ok(ah, channel->center_freq, channel->hw_value)) { 1058 ATH5K_ERR(ah->ah_sc, 1059 "channel frequency (%u MHz) out of supported " 1060 "band range\n", 1061 channel->center_freq); 1062 return -EINVAL; 1063 } 1064 1065 /* 1066 * Set the channel and wait 1067 */ 1068 switch (ah->ah_radio) { 1069 case AR5K_RF5110: 1070 ret = ath5k_hw_rf5110_channel(ah, channel); 1071 break; 1072 case AR5K_RF5111: 1073 ret = ath5k_hw_rf5111_channel(ah, channel); 1074 break; 1075 case AR5K_RF2425: 1076 ret = ath5k_hw_rf2425_channel(ah, channel); 1077 break; 1078 default: 1079 ret = ath5k_hw_rf5112_channel(ah, channel); 1080 break; 1081 } 1082 1083 if (ret) 1084 return ret; 1085 1086 /* Set JAPAN setting for channel 14 */ 1087 if (channel->center_freq == 2484) { 1088 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, 1089 AR5K_PHY_CCKTXCTL_JAPAN); 1090 } else { 1091 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, 1092 AR5K_PHY_CCKTXCTL_WORLD); 1093 } 1094 1095 ah->ah_current_channel = channel; 1096 ah->ah_turbo = channel->hw_value == CHANNEL_T ? true : false; 1097 1098 return 0; 1099} 1100 1101/*****************\ 1102 PHY calibration 1103\*****************/ 1104 1105void 1106ath5k_hw_calibration_poll(struct ath5k_hw *ah) 1107{ 1108 /* Calibration interval in jiffies */ 1109 unsigned long cal_intval; 1110 1111 cal_intval = msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_FULL); 1112 1113 /* Initialize timestamp if needed */ 1114 if (!ah->ah_cal_tstamp) 1115 ah->ah_cal_tstamp = jiffies; 1116 1117 /* For now we always do full calibration 1118 * Mark software interrupt mask and fire software 1119 * interrupt (bit gets auto-cleared) */ 1120 if (time_is_before_eq_jiffies(ah->ah_cal_tstamp + cal_intval)) { 1121 ah->ah_cal_tstamp = jiffies; 1122 ah->ah_swi_mask = AR5K_SWI_FULL_CALIBRATION; 1123 AR5K_REG_ENABLE_BITS(ah, AR5K_CR, AR5K_CR_SWI); 1124 } 1125} 1126 1127static int sign_extend(int val, const int nbits) 1128{ 1129 int order = BIT(nbits-1); 1130 return (val ^ order) - order; 1131} 1132 1133static s32 ath5k_hw_read_measured_noise_floor(struct ath5k_hw *ah) 1134{ 1135 s32 val; 1136 1137 val = ath5k_hw_reg_read(ah, AR5K_PHY_NF); 1138 return sign_extend(AR5K_REG_MS(val, AR5K_PHY_NF_MINCCA_PWR), 9); 1139} 1140 1141void ath5k_hw_init_nfcal_hist(struct ath5k_hw *ah) 1142{ 1143 int i; 1144 1145 ah->ah_nfcal_hist.index = 0; 1146 for (i = 0; i < ATH5K_NF_CAL_HIST_MAX; i++) 1147 ah->ah_nfcal_hist.nfval[i] = AR5K_TUNE_CCA_MAX_GOOD_VALUE; 1148} 1149 1150static void ath5k_hw_update_nfcal_hist(struct ath5k_hw *ah, s16 noise_floor) 1151{ 1152 struct ath5k_nfcal_hist *hist = &ah->ah_nfcal_hist; 1153 hist->index = (hist->index + 1) & (ATH5K_NF_CAL_HIST_MAX-1); 1154 hist->nfval[hist->index] = noise_floor; 1155} 1156 1157static s16 ath5k_hw_get_median_noise_floor(struct ath5k_hw *ah) 1158{ 1159 s16 sort[ATH5K_NF_CAL_HIST_MAX]; 1160 s16 tmp; 1161 int i, j; 1162 1163 memcpy(sort, ah->ah_nfcal_hist.nfval, sizeof(sort)); 1164 for (i = 0; i < ATH5K_NF_CAL_HIST_MAX - 1; i++) { 1165 for (j = 1; j < ATH5K_NF_CAL_HIST_MAX - i; j++) { 1166 if (sort[j] > sort[j-1]) { 1167 tmp = sort[j]; 1168 sort[j] = sort[j-1]; 1169 sort[j-1] = tmp; 1170 } 1171 } 1172 } 1173 for (i = 0; i < ATH5K_NF_CAL_HIST_MAX; i++) { 1174 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1175 "cal %d:%d\n", i, sort[i]); 1176 } 1177 return sort[(ATH5K_NF_CAL_HIST_MAX-1) / 2]; 1178} 1179 1180/* 1181 * When we tell the hardware to perform a noise floor calibration 1182 * by setting the AR5K_PHY_AGCCTL_NF bit, it will periodically 1183 * sample-and-hold the minimum noise level seen at the antennas. 1184 * This value is then stored in a ring buffer of recently measured 1185 * noise floor values so we have a moving window of the last few 1186 * samples. 1187 * 1188 * The median of the values in the history is then loaded into the 1189 * hardware for its own use for RSSI and CCA measurements. 1190 */ 1191static void ath5k_hw_update_noise_floor(struct ath5k_hw *ah) 1192{ 1193 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 1194 u32 val; 1195 s16 nf, threshold; 1196 u8 ee_mode; 1197 1198 /* keep last value if calibration hasn't completed */ 1199 if (ath5k_hw_reg_read(ah, AR5K_PHY_AGCCTL) & AR5K_PHY_AGCCTL_NF) { 1200 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1201 "NF did not complete in calibration window\n"); 1202 1203 return; 1204 } 1205 1206 switch (ah->ah_current_channel->hw_value & CHANNEL_MODES) { 1207 case CHANNEL_A: 1208 case CHANNEL_T: 1209 case CHANNEL_XR: 1210 ee_mode = AR5K_EEPROM_MODE_11A; 1211 break; 1212 case CHANNEL_G: 1213 case CHANNEL_TG: 1214 ee_mode = AR5K_EEPROM_MODE_11G; 1215 break; 1216 default: 1217 case CHANNEL_B: 1218 ee_mode = AR5K_EEPROM_MODE_11B; 1219 break; 1220 } 1221 1222 1223 /* completed NF calibration, test threshold */ 1224 nf = ath5k_hw_read_measured_noise_floor(ah); 1225 threshold = ee->ee_noise_floor_thr[ee_mode]; 1226 1227 if (nf > threshold) { 1228 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1229 "noise floor failure detected; " 1230 "read %d, threshold %d\n", 1231 nf, threshold); 1232 1233 nf = AR5K_TUNE_CCA_MAX_GOOD_VALUE; 1234 } 1235 1236 ath5k_hw_update_nfcal_hist(ah, nf); 1237 nf = ath5k_hw_get_median_noise_floor(ah); 1238 1239 /* load noise floor (in .5 dBm) so the hardware will use it */ 1240 val = ath5k_hw_reg_read(ah, AR5K_PHY_NF) & ~AR5K_PHY_NF_M; 1241 val |= (nf * 2) & AR5K_PHY_NF_M; 1242 ath5k_hw_reg_write(ah, val, AR5K_PHY_NF); 1243 1244 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_NF, 1245 ~(AR5K_PHY_AGCCTL_NF_EN | AR5K_PHY_AGCCTL_NF_NOUPDATE)); 1246 1247 ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_NF, 1248 0, false); 1249 1250 /* 1251 * Load a high max CCA Power value (-50 dBm in .5 dBm units) 1252 * so that we're not capped by the median we just loaded. 1253 * This will be used as the initial value for the next noise 1254 * floor calibration. 1255 */ 1256 val = (val & ~AR5K_PHY_NF_M) | ((-50 * 2) & AR5K_PHY_NF_M); 1257 ath5k_hw_reg_write(ah, val, AR5K_PHY_NF); 1258 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, 1259 AR5K_PHY_AGCCTL_NF_EN | 1260 AR5K_PHY_AGCCTL_NF_NOUPDATE | 1261 AR5K_PHY_AGCCTL_NF); 1262 1263 ah->ah_noise_floor = nf; 1264 1265 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1266 "noise floor calibrated: %d\n", nf); 1267} 1268 1269/* 1270 * Perform a PHY calibration on RF5110 1271 * -Fix BPSK/QAM Constellation (I/Q correction) 1272 * -Calculate Noise Floor 1273 */ 1274static int ath5k_hw_rf5110_calibrate(struct ath5k_hw *ah, 1275 struct ieee80211_channel *channel) 1276{ 1277 u32 phy_sig, phy_agc, phy_sat, beacon; 1278 int ret; 1279 1280 /* 1281 * Disable beacons and RX/TX queues, wait 1282 */ 1283 AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5210, 1284 AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210); 1285 beacon = ath5k_hw_reg_read(ah, AR5K_BEACON_5210); 1286 ath5k_hw_reg_write(ah, beacon & ~AR5K_BEACON_ENABLE, AR5K_BEACON_5210); 1287 1288 mdelay(2); 1289 1290 /* 1291 * Set the channel (with AGC turned off) 1292 */ 1293 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); 1294 udelay(10); 1295 ret = ath5k_hw_channel(ah, channel); 1296 1297 /* 1298 * Activate PHY and wait 1299 */ 1300 ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT); 1301 mdelay(1); 1302 1303 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); 1304 1305 if (ret) 1306 return ret; 1307 1308 /* 1309 * Calibrate the radio chip 1310 */ 1311 1312 /* Remember normal state */ 1313 phy_sig = ath5k_hw_reg_read(ah, AR5K_PHY_SIG); 1314 phy_agc = ath5k_hw_reg_read(ah, AR5K_PHY_AGCCOARSE); 1315 phy_sat = ath5k_hw_reg_read(ah, AR5K_PHY_ADCSAT); 1316 1317 /* Update radio registers */ 1318 ath5k_hw_reg_write(ah, (phy_sig & ~(AR5K_PHY_SIG_FIRPWR)) | 1319 AR5K_REG_SM(-1, AR5K_PHY_SIG_FIRPWR), AR5K_PHY_SIG); 1320 1321 ath5k_hw_reg_write(ah, (phy_agc & ~(AR5K_PHY_AGCCOARSE_HI | 1322 AR5K_PHY_AGCCOARSE_LO)) | 1323 AR5K_REG_SM(-1, AR5K_PHY_AGCCOARSE_HI) | 1324 AR5K_REG_SM(-127, AR5K_PHY_AGCCOARSE_LO), AR5K_PHY_AGCCOARSE); 1325 1326 ath5k_hw_reg_write(ah, (phy_sat & ~(AR5K_PHY_ADCSAT_ICNT | 1327 AR5K_PHY_ADCSAT_THR)) | 1328 AR5K_REG_SM(2, AR5K_PHY_ADCSAT_ICNT) | 1329 AR5K_REG_SM(12, AR5K_PHY_ADCSAT_THR), AR5K_PHY_ADCSAT); 1330 1331 udelay(20); 1332 1333 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); 1334 udelay(10); 1335 ath5k_hw_reg_write(ah, AR5K_PHY_RFSTG_DISABLE, AR5K_PHY_RFSTG); 1336 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); 1337 1338 mdelay(1); 1339 1340 /* 1341 * Enable calibration and wait until completion 1342 */ 1343 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_CAL); 1344 1345 ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, 1346 AR5K_PHY_AGCCTL_CAL, 0, false); 1347 1348 /* Reset to normal state */ 1349 ath5k_hw_reg_write(ah, phy_sig, AR5K_PHY_SIG); 1350 ath5k_hw_reg_write(ah, phy_agc, AR5K_PHY_AGCCOARSE); 1351 ath5k_hw_reg_write(ah, phy_sat, AR5K_PHY_ADCSAT); 1352 1353 if (ret) { 1354 ATH5K_ERR(ah->ah_sc, "calibration timeout (%uMHz)\n", 1355 channel->center_freq); 1356 return ret; 1357 } 1358 1359 ath5k_hw_update_noise_floor(ah); 1360 1361 /* 1362 * Re-enable RX/TX and beacons 1363 */ 1364 AR5K_REG_DISABLE_BITS(ah, AR5K_DIAG_SW_5210, 1365 AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210); 1366 ath5k_hw_reg_write(ah, beacon, AR5K_BEACON_5210); 1367 1368 return 0; 1369} 1370 1371/* 1372 * Perform a PHY calibration on RF5111/5112 and newer chips 1373 */ 1374static int ath5k_hw_rf511x_calibrate(struct ath5k_hw *ah, 1375 struct ieee80211_channel *channel) 1376{ 1377 u32 i_pwr, q_pwr; 1378 s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd; 1379 int i; 1380 ATH5K_TRACE(ah->ah_sc); 1381 1382 if (!ah->ah_calibration || 1383 ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) 1384 goto done; 1385 1386 /* Calibration has finished, get the results and re-run */ 1387 for (i = 0; i <= 10; i++) { 1388 iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR); 1389 i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I); 1390 q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q); 1391 } 1392 1393 i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7; 1394 1395 if (ah->ah_version == AR5K_AR5211) 1396 q_coffd = q_pwr >> 6; 1397 else 1398 q_coffd = q_pwr >> 7; 1399 1400 /* No correction */ 1401 if (i_coffd == 0 || q_coffd == 0) 1402 goto done; 1403 1404 i_coff = ((-iq_corr) / i_coffd); 1405 1406 /* Boundary check */ 1407 if (i_coff > 31) 1408 i_coff = 31; 1409 if (i_coff < -32) 1410 i_coff = -32; 1411 1412 if (ah->ah_version == AR5K_AR5211) 1413 q_coff = (i_pwr / q_coffd) - 64; 1414 else 1415 q_coff = (i_pwr / q_coffd) - 128; 1416 1417 /* Boundary check */ 1418 if (q_coff > 15) 1419 q_coff = 15; 1420 if (q_coff < -16) 1421 q_coff = -16; 1422 1423 /* Commit new I/Q value */ 1424 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE | 1425 ((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S)); 1426 1427 /* Re-enable calibration -if we don't we'll commit 1428 * the same values again and again */ 1429 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, 1430 AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); 1431 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_RUN); 1432 1433done: 1434 1435 /* TODO: Separate noise floor calibration from I/Q calibration 1436 * since noise floor calibration interrupts rx path while I/Q 1437 * calibration doesn't. We don't need to run noise floor calibration 1438 * as often as I/Q calibration.*/ 1439 ath5k_hw_update_noise_floor(ah); 1440 1441 /* Initiate a gain_F calibration */ 1442 ath5k_hw_request_rfgain_probe(ah); 1443 1444 return 0; 1445} 1446 1447/* 1448 * Perform a PHY calibration 1449 */ 1450int ath5k_hw_phy_calibrate(struct ath5k_hw *ah, 1451 struct ieee80211_channel *channel) 1452{ 1453 int ret; 1454 1455 if (ah->ah_radio == AR5K_RF5110) 1456 ret = ath5k_hw_rf5110_calibrate(ah, channel); 1457 else 1458 ret = ath5k_hw_rf511x_calibrate(ah, channel); 1459 1460 return ret; 1461} 1462 1463/***************************\ 1464* Spur mitigation functions * 1465\***************************/ 1466 1467bool ath5k_hw_chan_has_spur_noise(struct ath5k_hw *ah, 1468 struct ieee80211_channel *channel) 1469{ 1470 u8 refclk_freq; 1471 1472 if ((ah->ah_radio == AR5K_RF5112) || 1473 (ah->ah_radio == AR5K_RF5413) || 1474 (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) 1475 refclk_freq = 40; 1476 else 1477 refclk_freq = 32; 1478 1479 if ((channel->center_freq % refclk_freq != 0) && 1480 ((channel->center_freq % refclk_freq < 10) || 1481 (channel->center_freq % refclk_freq > 22))) 1482 return true; 1483 else 1484 return false; 1485} 1486 1487void 1488ath5k_hw_set_spur_mitigation_filter(struct ath5k_hw *ah, 1489 struct ieee80211_channel *channel) 1490{ 1491 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 1492 u32 mag_mask[4] = {0, 0, 0, 0}; 1493 u32 pilot_mask[2] = {0, 0}; 1494 /* Note: fbin values are scaled up by 2 */ 1495 u16 spur_chan_fbin, chan_fbin, symbol_width, spur_detection_window; 1496 s32 spur_delta_phase, spur_freq_sigma_delta; 1497 s32 spur_offset, num_symbols_x16; 1498 u8 num_symbol_offsets, i, freq_band; 1499 1500 /* Convert current frequency to fbin value (the same way channels 1501 * are stored on EEPROM, check out ath5k_eeprom_bin2freq) and scale 1502 * up by 2 so we can compare it later */ 1503 if (channel->hw_value & CHANNEL_2GHZ) { 1504 chan_fbin = (channel->center_freq - 2300) * 10; 1505 freq_band = AR5K_EEPROM_BAND_2GHZ; 1506 } else { 1507 chan_fbin = (channel->center_freq - 4900) * 10; 1508 freq_band = AR5K_EEPROM_BAND_5GHZ; 1509 } 1510 1511 /* Check if any spur_chan_fbin from EEPROM is 1512 * within our current channel's spur detection range */ 1513 spur_chan_fbin = AR5K_EEPROM_NO_SPUR; 1514 spur_detection_window = AR5K_SPUR_CHAN_WIDTH; 1515 /* XXX: Half/Quarter channels ?*/ 1516 if (channel->hw_value & CHANNEL_TURBO) 1517 spur_detection_window *= 2; 1518 1519 for (i = 0; i < AR5K_EEPROM_N_SPUR_CHANS; i++) { 1520 spur_chan_fbin = ee->ee_spur_chans[i][freq_band]; 1521 1522 /* Note: mask cleans AR5K_EEPROM_NO_SPUR flag 1523 * so it's zero if we got nothing from EEPROM */ 1524 if (spur_chan_fbin == AR5K_EEPROM_NO_SPUR) { 1525 spur_chan_fbin &= AR5K_EEPROM_SPUR_CHAN_MASK; 1526 break; 1527 } 1528 1529 if ((chan_fbin - spur_detection_window <= 1530 (spur_chan_fbin & AR5K_EEPROM_SPUR_CHAN_MASK)) && 1531 (chan_fbin + spur_detection_window >= 1532 (spur_chan_fbin & AR5K_EEPROM_SPUR_CHAN_MASK))) { 1533 spur_chan_fbin &= AR5K_EEPROM_SPUR_CHAN_MASK; 1534 break; 1535 } 1536 } 1537 1538 /* We need to enable spur filter for this channel */ 1539 if (spur_chan_fbin) { 1540 spur_offset = spur_chan_fbin - chan_fbin; 1541 /* 1542 * Calculate deltas: 1543 * spur_freq_sigma_delta -> spur_offset / sample_freq << 21 1544 * spur_delta_phase -> spur_offset / chip_freq << 11 1545 * Note: Both values have 100KHz resolution 1546 */ 1547 /* XXX: Half/Quarter rate channels ? */ 1548 switch (channel->hw_value) { 1549 case CHANNEL_A: 1550 /* Both sample_freq and chip_freq are 40MHz */ 1551 spur_delta_phase = (spur_offset << 17) / 25; 1552 spur_freq_sigma_delta = (spur_delta_phase >> 10); 1553 symbol_width = AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz; 1554 break; 1555 case CHANNEL_G: 1556 /* sample_freq -> 40MHz chip_freq -> 44MHz 1557 * (for b compatibility) */ 1558 spur_freq_sigma_delta = (spur_offset << 8) / 55; 1559 spur_delta_phase = (spur_offset << 17) / 25; 1560 symbol_width = AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz; 1561 break; 1562 case CHANNEL_T: 1563 case CHANNEL_TG: 1564 /* Both sample_freq and chip_freq are 80MHz */ 1565 spur_delta_phase = (spur_offset << 16) / 25; 1566 spur_freq_sigma_delta = (spur_delta_phase >> 10); 1567 symbol_width = AR5K_SPUR_SYMBOL_WIDTH_TURBO_100Hz; 1568 break; 1569 default: 1570 return; 1571 } 1572 1573 /* Calculate pilot and magnitude masks */ 1574 1575 /* Scale up spur_offset by 1000 to switch to 100HZ resolution 1576 * and divide by symbol_width to find how many symbols we have 1577 * Note: number of symbols is scaled up by 16 */ 1578 num_symbols_x16 = ((spur_offset * 1000) << 4) / symbol_width; 1579 1580 /* Spur is on a symbol if num_symbols_x16 % 16 is zero */ 1581 if (!(num_symbols_x16 & 0xF)) 1582 /* _X_ */ 1583 num_symbol_offsets = 3; 1584 else 1585 /* _xx_ */ 1586 num_symbol_offsets = 4; 1587 1588 for (i = 0; i < num_symbol_offsets; i++) { 1589 1590 /* Calculate pilot mask */ 1591 s32 curr_sym_off = 1592 (num_symbols_x16 / 16) + i + 25; 1593 1594 /* Pilot magnitude mask seems to be a way to 1595 * declare the boundaries for our detection 1596 * window or something, it's 2 for the middle 1597 * value(s) where the symbol is expected to be 1598 * and 1 on the boundary values */ 1599 u8 plt_mag_map = 1600 (i == 0 || i == (num_symbol_offsets - 1)) 1601 ? 1 : 2; 1602 1603 if (curr_sym_off >= 0 && curr_sym_off <= 32) { 1604 if (curr_sym_off <= 25) 1605 pilot_mask[0] |= 1 << curr_sym_off; 1606 else if (curr_sym_off >= 27) 1607 pilot_mask[0] |= 1 << (curr_sym_off - 1); 1608 } else if (curr_sym_off >= 33 && curr_sym_off <= 52) 1609 pilot_mask[1] |= 1 << (curr_sym_off - 33); 1610 1611 /* Calculate magnitude mask (for viterbi decoder) */ 1612 if (curr_sym_off >= -1 && curr_sym_off <= 14) 1613 mag_mask[0] |= 1614 plt_mag_map << (curr_sym_off + 1) * 2; 1615 else if (curr_sym_off >= 15 && curr_sym_off <= 30) 1616 mag_mask[1] |= 1617 plt_mag_map << (curr_sym_off - 15) * 2; 1618 else if (curr_sym_off >= 31 && curr_sym_off <= 46) 1619 mag_mask[2] |= 1620 plt_mag_map << (curr_sym_off - 31) * 2; 1621 else if (curr_sym_off >= 46 && curr_sym_off <= 53) 1622 mag_mask[3] |= 1623 plt_mag_map << (curr_sym_off - 47) * 2; 1624 1625 } 1626 1627 /* Write settings on hw to enable spur filter */ 1628 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, 1629 AR5K_PHY_BIN_MASK_CTL_RATE, 0xff); 1630 /* XXX: Self correlator also ? */ 1631 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, 1632 AR5K_PHY_IQ_PILOT_MASK_EN | 1633 AR5K_PHY_IQ_CHAN_MASK_EN | 1634 AR5K_PHY_IQ_SPUR_FILT_EN); 1635 1636 /* Set delta phase and freq sigma delta */ 1637 ath5k_hw_reg_write(ah, 1638 AR5K_REG_SM(spur_delta_phase, 1639 AR5K_PHY_TIMING_11_SPUR_DELTA_PHASE) | 1640 AR5K_REG_SM(spur_freq_sigma_delta, 1641 AR5K_PHY_TIMING_11_SPUR_FREQ_SD) | 1642 AR5K_PHY_TIMING_11_USE_SPUR_IN_AGC, 1643 AR5K_PHY_TIMING_11); 1644 1645 /* Write pilot masks */ 1646 ath5k_hw_reg_write(ah, pilot_mask[0], AR5K_PHY_TIMING_7); 1647 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_8, 1648 AR5K_PHY_TIMING_8_PILOT_MASK_2, 1649 pilot_mask[1]); 1650 1651 ath5k_hw_reg_write(ah, pilot_mask[0], AR5K_PHY_TIMING_9); 1652 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_10, 1653 AR5K_PHY_TIMING_10_PILOT_MASK_2, 1654 pilot_mask[1]); 1655 1656 /* Write magnitude masks */ 1657 ath5k_hw_reg_write(ah, mag_mask[0], AR5K_PHY_BIN_MASK_1); 1658 ath5k_hw_reg_write(ah, mag_mask[1], AR5K_PHY_BIN_MASK_2); 1659 ath5k_hw_reg_write(ah, mag_mask[2], AR5K_PHY_BIN_MASK_3); 1660 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, 1661 AR5K_PHY_BIN_MASK_CTL_MASK_4, 1662 mag_mask[3]); 1663 1664 ath5k_hw_reg_write(ah, mag_mask[0], AR5K_PHY_BIN_MASK2_1); 1665 ath5k_hw_reg_write(ah, mag_mask[1], AR5K_PHY_BIN_MASK2_2); 1666 ath5k_hw_reg_write(ah, mag_mask[2], AR5K_PHY_BIN_MASK2_3); 1667 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK2_4, 1668 AR5K_PHY_BIN_MASK2_4_MASK_4, 1669 mag_mask[3]); 1670 1671 } else if (ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & 1672 AR5K_PHY_IQ_SPUR_FILT_EN) { 1673 /* Clean up spur mitigation settings and disable fliter */ 1674 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, 1675 AR5K_PHY_BIN_MASK_CTL_RATE, 0); 1676 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_IQ, 1677 AR5K_PHY_IQ_PILOT_MASK_EN | 1678 AR5K_PHY_IQ_CHAN_MASK_EN | 1679 AR5K_PHY_IQ_SPUR_FILT_EN); 1680 ath5k_hw_reg_write(ah, 0, AR5K_PHY_TIMING_11); 1681 1682 /* Clear pilot masks */ 1683 ath5k_hw_reg_write(ah, 0, AR5K_PHY_TIMING_7); 1684 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_8, 1685 AR5K_PHY_TIMING_8_PILOT_MASK_2, 1686 0); 1687 1688 ath5k_hw_reg_write(ah, 0, AR5K_PHY_TIMING_9); 1689 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_10, 1690 AR5K_PHY_TIMING_10_PILOT_MASK_2, 1691 0); 1692 1693 /* Clear magnitude masks */ 1694 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK_1); 1695 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK_2); 1696 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK_3); 1697 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, 1698 AR5K_PHY_BIN_MASK_CTL_MASK_4, 1699 0); 1700 1701 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK2_1); 1702 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK2_2); 1703 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK2_3); 1704 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK2_4, 1705 AR5K_PHY_BIN_MASK2_4_MASK_4, 1706 0); 1707 } 1708} 1709 1710/********************\ 1711 Misc PHY functions 1712\********************/ 1713 1714int ath5k_hw_phy_disable(struct ath5k_hw *ah) 1715{ 1716 ATH5K_TRACE(ah->ah_sc); 1717 /*Just a try M.F.*/ 1718 ath5k_hw_reg_write(ah, AR5K_PHY_ACT_DISABLE, AR5K_PHY_ACT); 1719 1720 return 0; 1721} 1722 1723/* 1724 * Get the PHY Chip revision 1725 */ 1726u16 ath5k_hw_radio_revision(struct ath5k_hw *ah, unsigned int chan) 1727{ 1728 unsigned int i; 1729 u32 srev; 1730 u16 ret; 1731 1732 ATH5K_TRACE(ah->ah_sc); 1733 1734 /* 1735 * Set the radio chip access register 1736 */ 1737 switch (chan) { 1738 case CHANNEL_2GHZ: 1739 ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_2GHZ, AR5K_PHY(0)); 1740 break; 1741 case CHANNEL_5GHZ: 1742 ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); 1743 break; 1744 default: 1745 return 0; 1746 } 1747 1748 mdelay(2); 1749 1750 /* ...wait until PHY is ready and read the selected radio revision */ 1751 ath5k_hw_reg_write(ah, 0x00001c16, AR5K_PHY(0x34)); 1752 1753 for (i = 0; i < 8; i++) 1754 ath5k_hw_reg_write(ah, 0x00010000, AR5K_PHY(0x20)); 1755 1756 if (ah->ah_version == AR5K_AR5210) { 1757 srev = ath5k_hw_reg_read(ah, AR5K_PHY(256) >> 28) & 0xf; 1758 ret = (u16)ath5k_hw_bitswap(srev, 4) + 1; 1759 } else { 1760 srev = (ath5k_hw_reg_read(ah, AR5K_PHY(0x100)) >> 24) & 0xff; 1761 ret = (u16)ath5k_hw_bitswap(((srev & 0xf0) >> 4) | 1762 ((srev & 0x0f) << 4), 8); 1763 } 1764 1765 /* Reset to the 5GHz mode */ 1766 ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); 1767 1768 return ret; 1769} 1770 1771/*****************\ 1772* Antenna control * 1773\*****************/ 1774 1775static void /*TODO:Boundary check*/ 1776ath5k_hw_set_def_antenna(struct ath5k_hw *ah, u8 ant) 1777{ 1778 ATH5K_TRACE(ah->ah_sc); 1779 1780 if (ah->ah_version != AR5K_AR5210) 1781 ath5k_hw_reg_write(ah, ant & 0x7, AR5K_DEFAULT_ANTENNA); 1782} 1783 1784/* 1785 * Enable/disable fast rx antenna diversity 1786 */ 1787static void 1788ath5k_hw_set_fast_div(struct ath5k_hw *ah, u8 ee_mode, bool enable) 1789{ 1790 switch (ee_mode) { 1791 case AR5K_EEPROM_MODE_11G: 1792 /* XXX: This is set to 1793 * disabled on initvals !!! */ 1794 case AR5K_EEPROM_MODE_11A: 1795 if (enable) 1796 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGCCTL, 1797 AR5K_PHY_AGCCTL_OFDM_DIV_DIS); 1798 else 1799 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, 1800 AR5K_PHY_AGCCTL_OFDM_DIV_DIS); 1801 break; 1802 case AR5K_EEPROM_MODE_11B: 1803 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, 1804 AR5K_PHY_AGCCTL_OFDM_DIV_DIS); 1805 break; 1806 default: 1807 return; 1808 } 1809 1810 if (enable) { 1811 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_RESTART, 1812 AR5K_PHY_RESTART_DIV_GC, 0xc); 1813 1814 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_FAST_ANT_DIV, 1815 AR5K_PHY_FAST_ANT_DIV_EN); 1816 } else { 1817 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_RESTART, 1818 AR5K_PHY_RESTART_DIV_GC, 0x8); 1819 1820 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_FAST_ANT_DIV, 1821 AR5K_PHY_FAST_ANT_DIV_EN); 1822 } 1823} 1824 1825/* 1826 * Set antenna operating mode 1827 */ 1828void 1829ath5k_hw_set_antenna_mode(struct ath5k_hw *ah, u8 ant_mode) 1830{ 1831 struct ieee80211_channel *channel = ah->ah_current_channel; 1832 bool use_def_for_tx, update_def_on_tx, use_def_for_rts, fast_div; 1833 bool use_def_for_sg; 1834 u8 def_ant, tx_ant, ee_mode; 1835 u32 sta_id1 = 0; 1836 1837 def_ant = ah->ah_def_ant; 1838 1839 ATH5K_TRACE(ah->ah_sc); 1840 1841 switch (channel->hw_value & CHANNEL_MODES) { 1842 case CHANNEL_A: 1843 case CHANNEL_T: 1844 case CHANNEL_XR: 1845 ee_mode = AR5K_EEPROM_MODE_11A; 1846 break; 1847 case CHANNEL_G: 1848 case CHANNEL_TG: 1849 ee_mode = AR5K_EEPROM_MODE_11G; 1850 break; 1851 case CHANNEL_B: 1852 ee_mode = AR5K_EEPROM_MODE_11B; 1853 break; 1854 default: 1855 ATH5K_ERR(ah->ah_sc, 1856 "invalid channel: %d\n", channel->center_freq); 1857 return; 1858 } 1859 1860 switch (ant_mode) { 1861 case AR5K_ANTMODE_DEFAULT: 1862 tx_ant = 0; 1863 use_def_for_tx = false; 1864 update_def_on_tx = false; 1865 use_def_for_rts = false; 1866 use_def_for_sg = false; 1867 fast_div = true; 1868 break; 1869 case AR5K_ANTMODE_FIXED_A: 1870 def_ant = 1; 1871 tx_ant = 0; 1872 use_def_for_tx = true; 1873 update_def_on_tx = false; 1874 use_def_for_rts = true; 1875 use_def_for_sg = true; 1876 fast_div = false; 1877 break; 1878 case AR5K_ANTMODE_FIXED_B: 1879 def_ant = 2; 1880 tx_ant = 0; 1881 use_def_for_tx = true; 1882 update_def_on_tx = false; 1883 use_def_for_rts = true; 1884 use_def_for_sg = true; 1885 fast_div = false; 1886 break; 1887 case AR5K_ANTMODE_SINGLE_AP: 1888 def_ant = 1; /* updated on tx */ 1889 tx_ant = 0; 1890 use_def_for_tx = true; 1891 update_def_on_tx = true; 1892 use_def_for_rts = true; 1893 use_def_for_sg = true; 1894 fast_div = true; 1895 break; 1896 case AR5K_ANTMODE_SECTOR_AP: 1897 tx_ant = 1; /* variable */ 1898 use_def_for_tx = false; 1899 update_def_on_tx = false; 1900 use_def_for_rts = true; 1901 use_def_for_sg = false; 1902 fast_div = false; 1903 break; 1904 case AR5K_ANTMODE_SECTOR_STA: 1905 tx_ant = 1; /* variable */ 1906 use_def_for_tx = true; 1907 update_def_on_tx = false; 1908 use_def_for_rts = true; 1909 use_def_for_sg = false; 1910 fast_div = true; 1911 break; 1912 case AR5K_ANTMODE_DEBUG: 1913 def_ant = 1; 1914 tx_ant = 2; 1915 use_def_for_tx = false; 1916 update_def_on_tx = false; 1917 use_def_for_rts = false; 1918 use_def_for_sg = false; 1919 fast_div = false; 1920 break; 1921 default: 1922 return; 1923 } 1924 1925 ah->ah_tx_ant = tx_ant; 1926 ah->ah_ant_mode = ant_mode; 1927 ah->ah_def_ant = def_ant; 1928 1929 sta_id1 |= use_def_for_tx ? AR5K_STA_ID1_DEFAULT_ANTENNA : 0; 1930 sta_id1 |= update_def_on_tx ? AR5K_STA_ID1_DESC_ANTENNA : 0; 1931 sta_id1 |= use_def_for_rts ? AR5K_STA_ID1_RTS_DEF_ANTENNA : 0; 1932 sta_id1 |= use_def_for_sg ? AR5K_STA_ID1_SELFGEN_DEF_ANT : 0; 1933 1934 AR5K_REG_DISABLE_BITS(ah, AR5K_STA_ID1, AR5K_STA_ID1_ANTENNA_SETTINGS); 1935 1936 if (sta_id1) 1937 AR5K_REG_ENABLE_BITS(ah, AR5K_STA_ID1, sta_id1); 1938 1939 /* Note: set diversity before default antenna 1940 * because it won't work correctly */ 1941 ath5k_hw_set_fast_div(ah, ee_mode, fast_div); 1942 ath5k_hw_set_def_antenna(ah, def_ant); 1943} 1944 1945 1946/****************\ 1947* TX power setup * 1948\****************/ 1949 1950/* 1951 * Helper functions 1952 */ 1953 1954/* 1955 * Do linear interpolation between two given (x, y) points 1956 */ 1957static s16 1958ath5k_get_interpolated_value(s16 target, s16 x_left, s16 x_right, 1959 s16 y_left, s16 y_right) 1960{ 1961 s16 ratio, result; 1962 1963 /* Avoid divide by zero and skip interpolation 1964 * if we have the same point */ 1965 if ((x_left == x_right) || (y_left == y_right)) 1966 return y_left; 1967 1968 /* 1969 * Since we use ints and not fps, we need to scale up in 1970 * order to get a sane ratio value (or else we 'll eg. get 1971 * always 1 instead of 1.25, 1.75 etc). We scale up by 100 1972 * to have some accuracy both for 0.5 and 0.25 steps. 1973 */ 1974 ratio = ((100 * y_right - 100 * y_left)/(x_right - x_left)); 1975 1976 /* Now scale down to be in range */ 1977 result = y_left + (ratio * (target - x_left) / 100); 1978 1979 return result; 1980} 1981 1982/* 1983 * Find vertical boundary (min pwr) for the linear PCDAC curve. 1984 * 1985 * Since we have the top of the curve and we draw the line below 1986 * until we reach 1 (1 pcdac step) we need to know which point 1987 * (x value) that is so that we don't go below y axis and have negative 1988 * pcdac values when creating the curve, or fill the table with zeroes. 1989 */ 1990static s16 1991ath5k_get_linear_pcdac_min(const u8 *stepL, const u8 *stepR, 1992 const s16 *pwrL, const s16 *pwrR) 1993{ 1994 s8 tmp; 1995 s16 min_pwrL, min_pwrR; 1996 s16 pwr_i; 1997 1998 /* Some vendors write the same pcdac value twice !!! */ 1999 if (stepL[0] == stepL[1] || stepR[0] == stepR[1]) 2000 return max(pwrL[0], pwrR[0]); 2001 2002 if (pwrL[0] == pwrL[1]) 2003 min_pwrL = pwrL[0]; 2004 else { 2005 pwr_i = pwrL[0]; 2006 do { 2007 pwr_i--; 2008 tmp = (s8) ath5k_get_interpolated_value(pwr_i, 2009 pwrL[0], pwrL[1], 2010 stepL[0], stepL[1]); 2011 } while (tmp > 1); 2012 2013 min_pwrL = pwr_i; 2014 } 2015 2016 if (pwrR[0] == pwrR[1]) 2017 min_pwrR = pwrR[0]; 2018 else { 2019 pwr_i = pwrR[0]; 2020 do { 2021 pwr_i--; 2022 tmp = (s8) ath5k_get_interpolated_value(pwr_i, 2023 pwrR[0], pwrR[1], 2024 stepR[0], stepR[1]); 2025 } while (tmp > 1); 2026 2027 min_pwrR = pwr_i; 2028 } 2029 2030 /* Keep the right boundary so that it works for both curves */ 2031 return max(min_pwrL, min_pwrR); 2032} 2033 2034/* 2035 * Interpolate (pwr,vpd) points to create a Power to PDADC or a 2036 * Power to PCDAC curve. 2037 * 2038 * Each curve has power on x axis (in 0.5dB units) and PCDAC/PDADC 2039 * steps (offsets) on y axis. Power can go up to 31.5dB and max 2040 * PCDAC/PDADC step for each curve is 64 but we can write more than 2041 * one curves on hw so we can go up to 128 (which is the max step we 2042 * can write on the final table). 2043 * 2044 * We write y values (PCDAC/PDADC steps) on hw. 2045 */ 2046static void 2047ath5k_create_power_curve(s16 pmin, s16 pmax, 2048 const s16 *pwr, const u8 *vpd, 2049 u8 num_points, 2050 u8 *vpd_table, u8 type) 2051{ 2052 u8 idx[2] = { 0, 1 }; 2053 s16 pwr_i = 2*pmin; 2054 int i; 2055 2056 if (num_points < 2) 2057 return; 2058 2059 /* We want the whole line, so adjust boundaries 2060 * to cover the entire power range. Note that 2061 * power values are already 0.25dB so no need 2062 * to multiply pwr_i by 2 */ 2063 if (type == AR5K_PWRTABLE_LINEAR_PCDAC) { 2064 pwr_i = pmin; 2065 pmin = 0; 2066 pmax = 63; 2067 } 2068 2069 /* Find surrounding turning points (TPs) 2070 * and interpolate between them */ 2071 for (i = 0; (i <= (u16) (pmax - pmin)) && 2072 (i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) { 2073 2074 /* We passed the right TP, move to the next set of TPs 2075 * if we pass the last TP, extrapolate above using the last 2076 * two TPs for ratio */ 2077 if ((pwr_i > pwr[idx[1]]) && (idx[1] < num_points - 1)) { 2078 idx[0]++; 2079 idx[1]++; 2080 } 2081 2082 vpd_table[i] = (u8) ath5k_get_interpolated_value(pwr_i, 2083 pwr[idx[0]], pwr[idx[1]], 2084 vpd[idx[0]], vpd[idx[1]]); 2085 2086 /* Increase by 0.5dB 2087 * (0.25 dB units) */ 2088 pwr_i += 2; 2089 } 2090} 2091 2092/* 2093 * Get the surrounding per-channel power calibration piers 2094 * for a given frequency so that we can interpolate between 2095 * them and come up with an apropriate dataset for our current 2096 * channel. 2097 */ 2098static void 2099ath5k_get_chan_pcal_surrounding_piers(struct ath5k_hw *ah, 2100 struct ieee80211_channel *channel, 2101 struct ath5k_chan_pcal_info **pcinfo_l, 2102 struct ath5k_chan_pcal_info **pcinfo_r) 2103{ 2104 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 2105 struct ath5k_chan_pcal_info *pcinfo; 2106 u8 idx_l, idx_r; 2107 u8 mode, max, i; 2108 u32 target = channel->center_freq; 2109 2110 idx_l = 0; 2111 idx_r = 0; 2112 2113 if (!(channel->hw_value & CHANNEL_OFDM)) { 2114 pcinfo = ee->ee_pwr_cal_b; 2115 mode = AR5K_EEPROM_MODE_11B; 2116 } else if (channel->hw_value & CHANNEL_2GHZ) { 2117 pcinfo = ee->ee_pwr_cal_g; 2118 mode = AR5K_EEPROM_MODE_11G; 2119 } else { 2120 pcinfo = ee->ee_pwr_cal_a; 2121 mode = AR5K_EEPROM_MODE_11A; 2122 } 2123 max = ee->ee_n_piers[mode] - 1; 2124 2125 /* Frequency is below our calibrated 2126 * range. Use the lowest power curve 2127 * we have */ 2128 if (target < pcinfo[0].freq) { 2129 idx_l = idx_r = 0; 2130 goto done; 2131 } 2132 2133 /* Frequency is above our calibrated 2134 * range. Use the highest power curve 2135 * we have */ 2136 if (target > pcinfo[max].freq) { 2137 idx_l = idx_r = max; 2138 goto done; 2139 } 2140 2141 /* Frequency is inside our calibrated 2142 * channel range. Pick the surrounding 2143 * calibration piers so that we can 2144 * interpolate */ 2145 for (i = 0; i <= max; i++) { 2146 2147 /* Frequency matches one of our calibration 2148 * piers, no need to interpolate, just use 2149 * that calibration pier */ 2150 if (pcinfo[i].freq == target) { 2151 idx_l = idx_r = i; 2152 goto done; 2153 } 2154 2155 /* We found a calibration pier that's above 2156 * frequency, use this pier and the previous 2157 * one to interpolate */ 2158 if (target < pcinfo[i].freq) { 2159 idx_r = i; 2160 idx_l = idx_r - 1; 2161 goto done; 2162 } 2163 } 2164 2165done: 2166 *pcinfo_l = &pcinfo[idx_l]; 2167 *pcinfo_r = &pcinfo[idx_r]; 2168 2169 return; 2170} 2171 2172/* 2173 * Get the surrounding per-rate power calibration data 2174 * for a given frequency and interpolate between power 2175 * values to set max target power supported by hw for 2176 * each rate. 2177 */ 2178static void 2179ath5k_get_rate_pcal_data(struct ath5k_hw *ah, 2180 struct ieee80211_channel *channel, 2181 struct ath5k_rate_pcal_info *rates) 2182{ 2183 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 2184 struct ath5k_rate_pcal_info *rpinfo; 2185 u8 idx_l, idx_r; 2186 u8 mode, max, i; 2187 u32 target = channel->center_freq; 2188 2189 idx_l = 0; 2190 idx_r = 0; 2191 2192 if (!(channel->hw_value & CHANNEL_OFDM)) { 2193 rpinfo = ee->ee_rate_tpwr_b; 2194 mode = AR5K_EEPROM_MODE_11B; 2195 } else if (channel->hw_value & CHANNEL_2GHZ) { 2196 rpinfo = ee->ee_rate_tpwr_g; 2197 mode = AR5K_EEPROM_MODE_11G; 2198 } else { 2199 rpinfo = ee->ee_rate_tpwr_a; 2200 mode = AR5K_EEPROM_MODE_11A; 2201 } 2202 max = ee->ee_rate_target_pwr_num[mode] - 1; 2203 2204 /* Get the surrounding calibration 2205 * piers - same as above */ 2206 if (target < rpinfo[0].freq) { 2207 idx_l = idx_r = 0; 2208 goto done; 2209 } 2210 2211 if (target > rpinfo[max].freq) { 2212 idx_l = idx_r = max; 2213 goto done; 2214 } 2215 2216 for (i = 0; i <= max; i++) { 2217 2218 if (rpinfo[i].freq == target) { 2219 idx_l = idx_r = i; 2220 goto done; 2221 } 2222 2223 if (target < rpinfo[i].freq) { 2224 idx_r = i; 2225 idx_l = idx_r - 1; 2226 goto done; 2227 } 2228 } 2229 2230done: 2231 /* Now interpolate power value, based on the frequency */ 2232 rates->freq = target; 2233 2234 rates->target_power_6to24 = 2235 ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, 2236 rpinfo[idx_r].freq, 2237 rpinfo[idx_l].target_power_6to24, 2238 rpinfo[idx_r].target_power_6to24); 2239 2240 rates->target_power_36 = 2241 ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, 2242 rpinfo[idx_r].freq, 2243 rpinfo[idx_l].target_power_36, 2244 rpinfo[idx_r].target_power_36); 2245 2246 rates->target_power_48 = 2247 ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, 2248 rpinfo[idx_r].freq, 2249 rpinfo[idx_l].target_power_48, 2250 rpinfo[idx_r].target_power_48); 2251 2252 rates->target_power_54 = 2253 ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, 2254 rpinfo[idx_r].freq, 2255 rpinfo[idx_l].target_power_54, 2256 rpinfo[idx_r].target_power_54); 2257} 2258 2259/* 2260 * Get the max edge power for this channel if 2261 * we have such data from EEPROM's Conformance Test 2262 * Limits (CTL), and limit max power if needed. 2263 */ 2264static void 2265ath5k_get_max_ctl_power(struct ath5k_hw *ah, 2266 struct ieee80211_channel *channel) 2267{ 2268 struct ath_regulatory *regulatory = ath5k_hw_regulatory(ah); 2269 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 2270 struct ath5k_edge_power *rep = ee->ee_ctl_pwr; 2271 u8 *ctl_val = ee->ee_ctl; 2272 s16 max_chan_pwr = ah->ah_txpower.txp_max_pwr / 4; 2273 s16 edge_pwr = 0; 2274 u8 rep_idx; 2275 u8 i, ctl_mode; 2276 u8 ctl_idx = 0xFF; 2277 u32 target = channel->center_freq; 2278 2279 ctl_mode = ath_regd_get_band_ctl(regulatory, channel->band); 2280 2281 switch (channel->hw_value & CHANNEL_MODES) { 2282 case CHANNEL_A: 2283 ctl_mode |= AR5K_CTL_11A; 2284 break; 2285 case CHANNEL_G: 2286 ctl_mode |= AR5K_CTL_11G; 2287 break; 2288 case CHANNEL_B: 2289 ctl_mode |= AR5K_CTL_11B; 2290 break; 2291 case CHANNEL_T: 2292 ctl_mode |= AR5K_CTL_TURBO; 2293 break; 2294 case CHANNEL_TG: 2295 ctl_mode |= AR5K_CTL_TURBOG; 2296 break; 2297 case CHANNEL_XR: 2298 /* Fall through */ 2299 default: 2300 return; 2301 } 2302 2303 for (i = 0; i < ee->ee_ctls; i++) { 2304 if (ctl_val[i] == ctl_mode) { 2305 ctl_idx = i; 2306 break; 2307 } 2308 } 2309 2310 /* If we have a CTL dataset available grab it and find the 2311 * edge power for our frequency */ 2312 if (ctl_idx == 0xFF) 2313 return; 2314 2315 /* Edge powers are sorted by frequency from lower 2316 * to higher. Each CTL corresponds to 8 edge power 2317 * measurements. */ 2318 rep_idx = ctl_idx * AR5K_EEPROM_N_EDGES; 2319 2320 /* Don't do boundaries check because we 2321 * might have more that one bands defined 2322 * for this mode */ 2323 2324 /* Get the edge power that's closer to our 2325 * frequency */ 2326 for (i = 0; i < AR5K_EEPROM_N_EDGES; i++) { 2327 rep_idx += i; 2328 if (target <= rep[rep_idx].freq) 2329 edge_pwr = (s16) rep[rep_idx].edge; 2330 } 2331 2332 if (edge_pwr) 2333 ah->ah_txpower.txp_max_pwr = 4*min(edge_pwr, max_chan_pwr); 2334} 2335 2336 2337/* 2338 * Power to PCDAC table functions 2339 */ 2340 2341/* 2342 * Fill Power to PCDAC table on RF5111 2343 * 2344 * No further processing is needed for RF5111, the only thing we have to 2345 * do is fill the values below and above calibration range since eeprom data 2346 * may not cover the entire PCDAC table. 2347 */ 2348static void 2349ath5k_fill_pwr_to_pcdac_table(struct ath5k_hw *ah, s16* table_min, 2350 s16 *table_max) 2351{ 2352 u8 *pcdac_out = ah->ah_txpower.txp_pd_table; 2353 u8 *pcdac_tmp = ah->ah_txpower.tmpL[0]; 2354 u8 pcdac_0, pcdac_n, pcdac_i, pwr_idx, i; 2355 s16 min_pwr, max_pwr; 2356 2357 /* Get table boundaries */ 2358 min_pwr = table_min[0]; 2359 pcdac_0 = pcdac_tmp[0]; 2360 2361 max_pwr = table_max[0]; 2362 pcdac_n = pcdac_tmp[table_max[0] - table_min[0]]; 2363 2364 /* Extrapolate below minimum using pcdac_0 */ 2365 pcdac_i = 0; 2366 for (i = 0; i < min_pwr; i++) 2367 pcdac_out[pcdac_i++] = pcdac_0; 2368 2369 /* Copy values from pcdac_tmp */ 2370 pwr_idx = min_pwr; 2371 for (i = 0 ; pwr_idx <= max_pwr && 2372 pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE; i++) { 2373 pcdac_out[pcdac_i++] = pcdac_tmp[i]; 2374 pwr_idx++; 2375 } 2376 2377 /* Extrapolate above maximum */ 2378 while (pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE) 2379 pcdac_out[pcdac_i++] = pcdac_n; 2380 2381} 2382 2383/* 2384 * Combine available XPD Curves and fill Linear Power to PCDAC table 2385 * on RF5112 2386 * 2387 * RFX112 can have up to 2 curves (one for low txpower range and one for 2388 * higher txpower range). We need to put them both on pcdac_out and place 2389 * them in the correct location. In case we only have one curve available 2390 * just fit it on pcdac_out (it's supposed to cover the entire range of 2391 * available pwr levels since it's always the higher power curve). Extrapolate 2392 * below and above final table if needed. 2393 */ 2394static void 2395ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min, 2396 s16 *table_max, u8 pdcurves) 2397{ 2398 u8 *pcdac_out = ah->ah_txpower.txp_pd_table; 2399 u8 *pcdac_low_pwr; 2400 u8 *pcdac_high_pwr; 2401 u8 *pcdac_tmp; 2402 u8 pwr; 2403 s16 max_pwr_idx; 2404 s16 min_pwr_idx; 2405 s16 mid_pwr_idx = 0; 2406 /* Edge flag turs on the 7nth bit on the PCDAC 2407 * to delcare the higher power curve (force values 2408 * to be greater than 64). If we only have one curve 2409 * we don't need to set this, if we have 2 curves and 2410 * fill the table backwards this can also be used to 2411 * switch from higher power curve to lower power curve */ 2412 u8 edge_flag; 2413 int i; 2414 2415 /* When we have only one curve available 2416 * that's the higher power curve. If we have 2417 * two curves the first is the high power curve 2418 * and the next is the low power curve. */ 2419 if (pdcurves > 1) { 2420 pcdac_low_pwr = ah->ah_txpower.tmpL[1]; 2421 pcdac_high_pwr = ah->ah_txpower.tmpL[0]; 2422 mid_pwr_idx = table_max[1] - table_min[1] - 1; 2423 max_pwr_idx = (table_max[0] - table_min[0]) / 2; 2424 2425 /* If table size goes beyond 31.5dB, keep the 2426 * upper 31.5dB range when setting tx power. 2427 * Note: 126 = 31.5 dB in quarter dB steps */ 2428 if (table_max[0] - table_min[1] > 126) 2429 min_pwr_idx = table_max[0] - 126; 2430 else 2431 min_pwr_idx = table_min[1]; 2432 2433 /* Since we fill table backwards 2434 * start from high power curve */ 2435 pcdac_tmp = pcdac_high_pwr; 2436 2437 edge_flag = 0x40; 2438 } else { 2439 pcdac_low_pwr = ah->ah_txpower.tmpL[1]; /* Zeroed */ 2440 pcdac_high_pwr = ah->ah_txpower.tmpL[0]; 2441 min_pwr_idx = table_min[0]; 2442 max_pwr_idx = (table_max[0] - table_min[0]) / 2; 2443 pcdac_tmp = pcdac_high_pwr; 2444 edge_flag = 0; 2445 } 2446 2447 /* This is used when setting tx power*/ 2448 ah->ah_txpower.txp_min_idx = min_pwr_idx/2; 2449 2450 /* Fill Power to PCDAC table backwards */ 2451 pwr = max_pwr_idx; 2452 for (i = 63; i >= 0; i--) { 2453 /* Entering lower power range, reset 2454 * edge flag and set pcdac_tmp to lower 2455 * power curve.*/ 2456 if (edge_flag == 0x40 && 2457 (2*pwr <= (table_max[1] - table_min[0]) || pwr == 0)) { 2458 edge_flag = 0x00; 2459 pcdac_tmp = pcdac_low_pwr; 2460 pwr = mid_pwr_idx/2; 2461 } 2462 2463 /* Don't go below 1, extrapolate below if we have 2464 * already swithced to the lower power curve -or 2465 * we only have one curve and edge_flag is zero 2466 * anyway */ 2467 if (pcdac_tmp[pwr] < 1 && (edge_flag == 0x00)) { 2468 while (i >= 0) { 2469 pcdac_out[i] = pcdac_out[i + 1]; 2470 i--; 2471 } 2472 break; 2473 } 2474 2475 pcdac_out[i] = pcdac_tmp[pwr] | edge_flag; 2476 2477 /* Extrapolate above if pcdac is greater than 2478 * 126 -this can happen because we OR pcdac_out 2479 * value with edge_flag on high power curve */ 2480 if (pcdac_out[i] > 126) 2481 pcdac_out[i] = 126; 2482 2483 /* Decrease by a 0.5dB step */ 2484 pwr--; 2485 } 2486} 2487 2488/* Write PCDAC values on hw */ 2489static void 2490ath5k_setup_pcdac_table(struct ath5k_hw *ah) 2491{ 2492 u8 *pcdac_out = ah->ah_txpower.txp_pd_table; 2493 int i; 2494 2495 /* 2496 * Write TX power values 2497 */ 2498 for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) { 2499 ath5k_hw_reg_write(ah, 2500 (((pcdac_out[2*i + 0] << 8 | 0xff) & 0xffff) << 0) | 2501 (((pcdac_out[2*i + 1] << 8 | 0xff) & 0xffff) << 16), 2502 AR5K_PHY_PCDAC_TXPOWER(i)); 2503 } 2504} 2505 2506 2507/* 2508 * Power to PDADC table functions 2509 */ 2510 2511/* 2512 * Set the gain boundaries and create final Power to PDADC table 2513 * 2514 * We can have up to 4 pd curves, we need to do a simmilar process 2515 * as we do for RF5112. This time we don't have an edge_flag but we 2516 * set the gain boundaries on a separate register. 2517 */ 2518static void 2519ath5k_combine_pwr_to_pdadc_curves(struct ath5k_hw *ah, 2520 s16 *pwr_min, s16 *pwr_max, u8 pdcurves) 2521{ 2522 u8 gain_boundaries[AR5K_EEPROM_N_PD_GAINS]; 2523 u8 *pdadc_out = ah->ah_txpower.txp_pd_table; 2524 u8 *pdadc_tmp; 2525 s16 pdadc_0; 2526 u8 pdadc_i, pdadc_n, pwr_step, pdg, max_idx, table_size; 2527 u8 pd_gain_overlap; 2528 2529 /* Note: Register value is initialized on initvals 2530 * there is no feedback from hw. 2531 * XXX: What about pd_gain_overlap from EEPROM ? */ 2532 pd_gain_overlap = (u8) ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG5) & 2533 AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP; 2534 2535 /* Create final PDADC table */ 2536 for (pdg = 0, pdadc_i = 0; pdg < pdcurves; pdg++) { 2537 pdadc_tmp = ah->ah_txpower.tmpL[pdg]; 2538 2539 if (pdg == pdcurves - 1) 2540 /* 2 dB boundary stretch for last 2541 * (higher power) curve */ 2542 gain_boundaries[pdg] = pwr_max[pdg] + 4; 2543 else 2544 /* Set gain boundary in the middle 2545 * between this curve and the next one */ 2546 gain_boundaries[pdg] = 2547 (pwr_max[pdg] + pwr_min[pdg + 1]) / 2; 2548 2549 /* Sanity check in case our 2 db stretch got out of 2550 * range. */ 2551 if (gain_boundaries[pdg] > AR5K_TUNE_MAX_TXPOWER) 2552 gain_boundaries[pdg] = AR5K_TUNE_MAX_TXPOWER; 2553 2554 /* For the first curve (lower power) 2555 * start from 0 dB */ 2556 if (pdg == 0) 2557 pdadc_0 = 0; 2558 else 2559 /* For the other curves use the gain overlap */ 2560 pdadc_0 = (gain_boundaries[pdg - 1] - pwr_min[pdg]) - 2561 pd_gain_overlap; 2562 2563 /* Force each power step to be at least 0.5 dB */ 2564 if ((pdadc_tmp[1] - pdadc_tmp[0]) > 1) 2565 pwr_step = pdadc_tmp[1] - pdadc_tmp[0]; 2566 else 2567 pwr_step = 1; 2568 2569 /* If pdadc_0 is negative, we need to extrapolate 2570 * below this pdgain by a number of pwr_steps */ 2571 while ((pdadc_0 < 0) && (pdadc_i < 128)) { 2572 s16 tmp = pdadc_tmp[0] + pdadc_0 * pwr_step; 2573 pdadc_out[pdadc_i++] = (tmp < 0) ? 0 : (u8) tmp; 2574 pdadc_0++; 2575 } 2576 2577 /* Set last pwr level, using gain boundaries */ 2578 pdadc_n = gain_boundaries[pdg] + pd_gain_overlap - pwr_min[pdg]; 2579 /* Limit it to be inside pwr range */ 2580 table_size = pwr_max[pdg] - pwr_min[pdg]; 2581 max_idx = (pdadc_n < table_size) ? pdadc_n : table_size; 2582 2583 /* Fill pdadc_out table */ 2584 while (pdadc_0 < max_idx) 2585 pdadc_out[pdadc_i++] = pdadc_tmp[pdadc_0++]; 2586 2587 /* Need to extrapolate above this pdgain? */ 2588 if (pdadc_n <= max_idx) 2589 continue; 2590 2591 /* Force each power step to be at least 0.5 dB */ 2592 if ((pdadc_tmp[table_size - 1] - pdadc_tmp[table_size - 2]) > 1) 2593 pwr_step = pdadc_tmp[table_size - 1] - 2594 pdadc_tmp[table_size - 2]; 2595 else 2596 pwr_step = 1; 2597 2598 /* Extrapolate above */ 2599 while ((pdadc_0 < (s16) pdadc_n) && 2600 (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2)) { 2601 s16 tmp = pdadc_tmp[table_size - 1] + 2602 (pdadc_0 - max_idx) * pwr_step; 2603 pdadc_out[pdadc_i++] = (tmp > 127) ? 127 : (u8) tmp; 2604 pdadc_0++; 2605 } 2606 } 2607 2608 while (pdg < AR5K_EEPROM_N_PD_GAINS) { 2609 gain_boundaries[pdg] = gain_boundaries[pdg - 1]; 2610 pdg++; 2611 } 2612 2613 while (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2) { 2614 pdadc_out[pdadc_i] = pdadc_out[pdadc_i - 1]; 2615 pdadc_i++; 2616 } 2617 2618 /* Set gain boundaries */ 2619 ath5k_hw_reg_write(ah, 2620 AR5K_REG_SM(pd_gain_overlap, 2621 AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP) | 2622 AR5K_REG_SM(gain_boundaries[0], 2623 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_1) | 2624 AR5K_REG_SM(gain_boundaries[1], 2625 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_2) | 2626 AR5K_REG_SM(gain_boundaries[2], 2627 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_3) | 2628 AR5K_REG_SM(gain_boundaries[3], 2629 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_4), 2630 AR5K_PHY_TPC_RG5); 2631 2632 /* Used for setting rate power table */ 2633 ah->ah_txpower.txp_min_idx = pwr_min[0]; 2634 2635} 2636 2637/* Write PDADC values on hw */ 2638static void 2639ath5k_setup_pwr_to_pdadc_table(struct ath5k_hw *ah, 2640 u8 pdcurves, u8 *pdg_to_idx) 2641{ 2642 u8 *pdadc_out = ah->ah_txpower.txp_pd_table; 2643 u32 reg; 2644 u8 i; 2645 2646 /* Select the right pdgain curves */ 2647 2648 /* Clear current settings */ 2649 reg = ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG1); 2650 reg &= ~(AR5K_PHY_TPC_RG1_PDGAIN_1 | 2651 AR5K_PHY_TPC_RG1_PDGAIN_2 | 2652 AR5K_PHY_TPC_RG1_PDGAIN_3 | 2653 AR5K_PHY_TPC_RG1_NUM_PD_GAIN); 2654 2655 /* 2656 * Use pd_gains curve from eeprom 2657 * 2658 * This overrides the default setting from initvals 2659 * in case some vendors (e.g. Zcomax) don't use the default 2660 * curves. If we don't honor their settings we 'll get a 2661 * 5dB (1 * gain overlap ?) drop. 2662 */ 2663 reg |= AR5K_REG_SM(pdcurves, AR5K_PHY_TPC_RG1_NUM_PD_GAIN); 2664 2665 switch (pdcurves) { 2666 case 3: 2667 reg |= AR5K_REG_SM(pdg_to_idx[2], AR5K_PHY_TPC_RG1_PDGAIN_3); 2668 /* Fall through */ 2669 case 2: 2670 reg |= AR5K_REG_SM(pdg_to_idx[1], AR5K_PHY_TPC_RG1_PDGAIN_2); 2671 /* Fall through */ 2672 case 1: 2673 reg |= AR5K_REG_SM(pdg_to_idx[0], AR5K_PHY_TPC_RG1_PDGAIN_1); 2674 break; 2675 } 2676 ath5k_hw_reg_write(ah, reg, AR5K_PHY_TPC_RG1); 2677 2678 /* 2679 * Write TX power values 2680 */ 2681 for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) { 2682 ath5k_hw_reg_write(ah, 2683 ((pdadc_out[4*i + 0] & 0xff) << 0) | 2684 ((pdadc_out[4*i + 1] & 0xff) << 8) | 2685 ((pdadc_out[4*i + 2] & 0xff) << 16) | 2686 ((pdadc_out[4*i + 3] & 0xff) << 24), 2687 AR5K_PHY_PDADC_TXPOWER(i)); 2688 } 2689} 2690 2691 2692/* 2693 * Common code for PCDAC/PDADC tables 2694 */ 2695 2696/* 2697 * This is the main function that uses all of the above 2698 * to set PCDAC/PDADC table on hw for the current channel. 2699 * This table is used for tx power calibration on the basband, 2700 * without it we get weird tx power levels and in some cases 2701 * distorted spectral mask 2702 */ 2703static int 2704ath5k_setup_channel_powertable(struct ath5k_hw *ah, 2705 struct ieee80211_channel *channel, 2706 u8 ee_mode, u8 type) 2707{ 2708 struct ath5k_pdgain_info *pdg_L, *pdg_R; 2709 struct ath5k_chan_pcal_info *pcinfo_L; 2710 struct ath5k_chan_pcal_info *pcinfo_R; 2711 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 2712 u8 *pdg_curve_to_idx = ee->ee_pdc_to_idx[ee_mode]; 2713 s16 table_min[AR5K_EEPROM_N_PD_GAINS]; 2714 s16 table_max[AR5K_EEPROM_N_PD_GAINS]; 2715 u8 *tmpL; 2716 u8 *tmpR; 2717 u32 target = channel->center_freq; 2718 int pdg, i; 2719 2720 /* Get surounding freq piers for this channel */ 2721 ath5k_get_chan_pcal_surrounding_piers(ah, channel, 2722 &pcinfo_L, 2723 &pcinfo_R); 2724 2725 /* Loop over pd gain curves on 2726 * surounding freq piers by index */ 2727 for (pdg = 0; pdg < ee->ee_pd_gains[ee_mode]; pdg++) { 2728 2729 /* Fill curves in reverse order 2730 * from lower power (max gain) 2731 * to higher power. Use curve -> idx 2732 * backmapping we did on eeprom init */ 2733 u8 idx = pdg_curve_to_idx[pdg]; 2734 2735 /* Grab the needed curves by index */ 2736 pdg_L = &pcinfo_L->pd_curves[idx]; 2737 pdg_R = &pcinfo_R->pd_curves[idx]; 2738 2739 /* Initialize the temp tables */ 2740 tmpL = ah->ah_txpower.tmpL[pdg]; 2741 tmpR = ah->ah_txpower.tmpR[pdg]; 2742 2743 /* Set curve's x boundaries and create 2744 * curves so that they cover the same 2745 * range (if we don't do that one table 2746 * will have values on some range and the 2747 * other one won't have any so interpolation 2748 * will fail) */ 2749 table_min[pdg] = min(pdg_L->pd_pwr[0], 2750 pdg_R->pd_pwr[0]) / 2; 2751 2752 table_max[pdg] = max(pdg_L->pd_pwr[pdg_L->pd_points - 1], 2753 pdg_R->pd_pwr[pdg_R->pd_points - 1]) / 2; 2754 2755 /* Now create the curves on surrounding channels 2756 * and interpolate if needed to get the final 2757 * curve for this gain on this channel */ 2758 switch (type) { 2759 case AR5K_PWRTABLE_LINEAR_PCDAC: 2760 /* Override min/max so that we don't loose 2761 * accuracy (don't divide by 2) */ 2762 table_min[pdg] = min(pdg_L->pd_pwr[0], 2763 pdg_R->pd_pwr[0]); 2764 2765 table_max[pdg] = 2766 max(pdg_L->pd_pwr[pdg_L->pd_points - 1], 2767 pdg_R->pd_pwr[pdg_R->pd_points - 1]); 2768 2769 /* Override minimum so that we don't get 2770 * out of bounds while extrapolating 2771 * below. Don't do this when we have 2 2772 * curves and we are on the high power curve 2773 * because table_min is ok in this case */ 2774 if (!(ee->ee_pd_gains[ee_mode] > 1 && pdg == 0)) { 2775 2776 table_min[pdg] = 2777 ath5k_get_linear_pcdac_min(pdg_L->pd_step, 2778 pdg_R->pd_step, 2779 pdg_L->pd_pwr, 2780 pdg_R->pd_pwr); 2781 2782 /* Don't go too low because we will 2783 * miss the upper part of the curve. 2784 * Note: 126 = 31.5dB (max power supported) 2785 * in 0.25dB units */ 2786 if (table_max[pdg] - table_min[pdg] > 126) 2787 table_min[pdg] = table_max[pdg] - 126; 2788 } 2789 2790 /* Fall through */ 2791 case AR5K_PWRTABLE_PWR_TO_PCDAC: 2792 case AR5K_PWRTABLE_PWR_TO_PDADC: 2793 2794 ath5k_create_power_curve(table_min[pdg], 2795 table_max[pdg], 2796 pdg_L->pd_pwr, 2797 pdg_L->pd_step, 2798 pdg_L->pd_points, tmpL, type); 2799 2800 /* We are in a calibration 2801 * pier, no need to interpolate 2802 * between freq piers */ 2803 if (pcinfo_L == pcinfo_R) 2804 continue; 2805 2806 ath5k_create_power_curve(table_min[pdg], 2807 table_max[pdg], 2808 pdg_R->pd_pwr, 2809 pdg_R->pd_step, 2810 pdg_R->pd_points, tmpR, type); 2811 break; 2812 default: 2813 return -EINVAL; 2814 } 2815 2816 /* Interpolate between curves 2817 * of surounding freq piers to 2818 * get the final curve for this 2819 * pd gain. Re-use tmpL for interpolation 2820 * output */ 2821 for (i = 0; (i < (u16) (table_max[pdg] - table_min[pdg])) && 2822 (i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) { 2823 tmpL[i] = (u8) ath5k_get_interpolated_value(target, 2824 (s16) pcinfo_L->freq, 2825 (s16) pcinfo_R->freq, 2826 (s16) tmpL[i], 2827 (s16) tmpR[i]); 2828 } 2829 } 2830 2831 /* Now we have a set of curves for this 2832 * channel on tmpL (x range is table_max - table_min 2833 * and y values are tmpL[pdg][]) sorted in the same 2834 * order as EEPROM (because we've used the backmapping). 2835 * So for RF5112 it's from higher power to lower power 2836 * and for RF2413 it's from lower power to higher power. 2837 * For RF5111 we only have one curve. */ 2838 2839 /* Fill min and max power levels for this 2840 * channel by interpolating the values on 2841 * surounding channels to complete the dataset */ 2842 ah->ah_txpower.txp_min_pwr = ath5k_get_interpolated_value(target, 2843 (s16) pcinfo_L->freq, 2844 (s16) pcinfo_R->freq, 2845 pcinfo_L->min_pwr, pcinfo_R->min_pwr); 2846 2847 ah->ah_txpower.txp_max_pwr = ath5k_get_interpolated_value(target, 2848 (s16) pcinfo_L->freq, 2849 (s16) pcinfo_R->freq, 2850 pcinfo_L->max_pwr, pcinfo_R->max_pwr); 2851 2852 /* We are ready to go, fill PCDAC/PDADC 2853 * table and write settings on hardware */ 2854 switch (type) { 2855 case AR5K_PWRTABLE_LINEAR_PCDAC: 2856 /* For RF5112 we can have one or two curves 2857 * and each curve covers a certain power lvl 2858 * range so we need to do some more processing */ 2859 ath5k_combine_linear_pcdac_curves(ah, table_min, table_max, 2860 ee->ee_pd_gains[ee_mode]); 2861 2862 /* Set txp.offset so that we can 2863 * match max power value with max 2864 * table index */ 2865 ah->ah_txpower.txp_offset = 64 - (table_max[0] / 2); 2866 2867 /* Write settings on hw */ 2868 ath5k_setup_pcdac_table(ah); 2869 break; 2870 case AR5K_PWRTABLE_PWR_TO_PCDAC: 2871 /* We are done for RF5111 since it has only 2872 * one curve, just fit the curve on the table */ 2873 ath5k_fill_pwr_to_pcdac_table(ah, table_min, table_max); 2874 2875 /* No rate powertable adjustment for RF5111 */ 2876 ah->ah_txpower.txp_min_idx = 0; 2877 ah->ah_txpower.txp_offset = 0; 2878 2879 /* Write settings on hw */ 2880 ath5k_setup_pcdac_table(ah); 2881 break; 2882 case AR5K_PWRTABLE_PWR_TO_PDADC: 2883 /* Set PDADC boundaries and fill 2884 * final PDADC table */ 2885 ath5k_combine_pwr_to_pdadc_curves(ah, table_min, table_max, 2886 ee->ee_pd_gains[ee_mode]); 2887 2888 /* Write settings on hw */ 2889 ath5k_setup_pwr_to_pdadc_table(ah, pdg, pdg_curve_to_idx); 2890 2891 /* Set txp.offset, note that table_min 2892 * can be negative */ 2893 ah->ah_txpower.txp_offset = table_min[0]; 2894 break; 2895 default: 2896 return -EINVAL; 2897 } 2898 2899 return 0; 2900} 2901 2902 2903/* 2904 * Per-rate tx power setting 2905 * 2906 * This is the code that sets the desired tx power (below 2907 * maximum) on hw for each rate (we also have TPC that sets 2908 * power per packet). We do that by providing an index on the 2909 * PCDAC/PDADC table we set up. 2910 */ 2911 2912/* 2913 * Set rate power table 2914 * 2915 * For now we only limit txpower based on maximum tx power 2916 * supported by hw (what's inside rate_info). We need to limit 2917 * this even more, based on regulatory domain etc. 2918 * 2919 * Rate power table contains indices to PCDAC/PDADC table (0.5dB steps) 2920 * and is indexed as follows: 2921 * rates[0] - rates[7] -> OFDM rates 2922 * rates[8] - rates[14] -> CCK rates 2923 * rates[15] -> XR rates (they all have the same power) 2924 */ 2925static void 2926ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr, 2927 struct ath5k_rate_pcal_info *rate_info, 2928 u8 ee_mode) 2929{ 2930 unsigned int i; 2931 u16 *rates; 2932 2933 /* max_pwr is power level we got from driver/user in 0.5dB 2934 * units, switch to 0.25dB units so we can compare */ 2935 max_pwr *= 2; 2936 max_pwr = min(max_pwr, (u16) ah->ah_txpower.txp_max_pwr) / 2; 2937 2938 /* apply rate limits */ 2939 rates = ah->ah_txpower.txp_rates_power_table; 2940 2941 /* OFDM rates 6 to 24Mb/s */ 2942 for (i = 0; i < 5; i++) 2943 rates[i] = min(max_pwr, rate_info->target_power_6to24); 2944 2945 /* Rest OFDM rates */ 2946 rates[5] = min(rates[0], rate_info->target_power_36); 2947 rates[6] = min(rates[0], rate_info->target_power_48); 2948 rates[7] = min(rates[0], rate_info->target_power_54); 2949 2950 /* CCK rates */ 2951 /* 1L */ 2952 rates[8] = min(rates[0], rate_info->target_power_6to24); 2953 /* 2L */ 2954 rates[9] = min(rates[0], rate_info->target_power_36); 2955 /* 2S */ 2956 rates[10] = min(rates[0], rate_info->target_power_36); 2957 /* 5L */ 2958 rates[11] = min(rates[0], rate_info->target_power_48); 2959 /* 5S */ 2960 rates[12] = min(rates[0], rate_info->target_power_48); 2961 /* 11L */ 2962 rates[13] = min(rates[0], rate_info->target_power_54); 2963 /* 11S */ 2964 rates[14] = min(rates[0], rate_info->target_power_54); 2965 2966 /* XR rates */ 2967 rates[15] = min(rates[0], rate_info->target_power_6to24); 2968 2969 /* CCK rates have different peak to average ratio 2970 * so we have to tweak their power so that gainf 2971 * correction works ok. For this we use OFDM to 2972 * CCK delta from eeprom */ 2973 if ((ee_mode == AR5K_EEPROM_MODE_11G) && 2974 (ah->ah_phy_revision < AR5K_SREV_PHY_5212A)) 2975 for (i = 8; i <= 15; i++) 2976 rates[i] -= ah->ah_txpower.txp_cck_ofdm_gainf_delta; 2977 2978 /* Now that we have all rates setup use table offset to 2979 * match the power range set by user with the power indices 2980 * on PCDAC/PDADC table */ 2981 for (i = 0; i < 16; i++) { 2982 rates[i] += ah->ah_txpower.txp_offset; 2983 /* Don't get out of bounds */ 2984 if (rates[i] > 63) 2985 rates[i] = 63; 2986 } 2987 2988 /* Min/max in 0.25dB units */ 2989 ah->ah_txpower.txp_min_pwr = 2 * rates[7]; 2990 ah->ah_txpower.txp_max_pwr = 2 * rates[0]; 2991 ah->ah_txpower.txp_ofdm = rates[7]; 2992} 2993 2994 2995/* 2996 * Set transmition power 2997 */ 2998int 2999ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, 3000 u8 ee_mode, u8 txpower) 3001{ 3002 struct ath5k_rate_pcal_info rate_info; 3003 u8 type; 3004 int ret; 3005 3006 ATH5K_TRACE(ah->ah_sc); 3007 if (txpower > AR5K_TUNE_MAX_TXPOWER) { 3008 ATH5K_ERR(ah->ah_sc, "invalid tx power: %u\n", txpower); 3009 return -EINVAL; 3010 } 3011 3012 /* Reset TX power values */ 3013 memset(&ah->ah_txpower, 0, sizeof(ah->ah_txpower)); 3014 ah->ah_txpower.txp_tpc = AR5K_TUNE_TPC_TXPOWER; 3015 ah->ah_txpower.txp_min_pwr = 0; 3016 ah->ah_txpower.txp_max_pwr = AR5K_TUNE_MAX_TXPOWER; 3017 3018 /* Initialize TX power table */ 3019 switch (ah->ah_radio) { 3020 case AR5K_RF5111: 3021 type = AR5K_PWRTABLE_PWR_TO_PCDAC; 3022 break; 3023 case AR5K_RF5112: 3024 type = AR5K_PWRTABLE_LINEAR_PCDAC; 3025 break; 3026 case AR5K_RF2413: 3027 case AR5K_RF5413: 3028 case AR5K_RF2316: 3029 case AR5K_RF2317: 3030 case AR5K_RF2425: 3031 type = AR5K_PWRTABLE_PWR_TO_PDADC; 3032 break; 3033 default: 3034 return -EINVAL; 3035 } 3036 3037 /* FIXME: Only on channel/mode change */ 3038 ret = ath5k_setup_channel_powertable(ah, channel, ee_mode, type); 3039 if (ret) 3040 return ret; 3041 3042 /* Limit max power if we have a CTL available */ 3043 ath5k_get_max_ctl_power(ah, channel); 3044 3045 /* FIXME: Tx power limit for this regdomain 3046 * XXX: Mac80211/CRDA will do that anyway ? */ 3047 3048 /* FIXME: Antenna reduction stuff */ 3049 3050 /* FIXME: Limit power on turbo modes */ 3051 3052 /* FIXME: TPC scale reduction */ 3053 3054 /* Get surounding channels for per-rate power table 3055 * calibration */ 3056 ath5k_get_rate_pcal_data(ah, channel, &rate_info); 3057 3058 /* Setup rate power table */ 3059 ath5k_setup_rate_powertable(ah, txpower, &rate_info, ee_mode); 3060 3061 /* Write rate power table on hw */ 3062 ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(3, 24) | 3063 AR5K_TXPOWER_OFDM(2, 16) | AR5K_TXPOWER_OFDM(1, 8) | 3064 AR5K_TXPOWER_OFDM(0, 0), AR5K_PHY_TXPOWER_RATE1); 3065 3066 ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(7, 24) | 3067 AR5K_TXPOWER_OFDM(6, 16) | AR5K_TXPOWER_OFDM(5, 8) | 3068 AR5K_TXPOWER_OFDM(4, 0), AR5K_PHY_TXPOWER_RATE2); 3069 3070 ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(10, 24) | 3071 AR5K_TXPOWER_CCK(9, 16) | AR5K_TXPOWER_CCK(15, 8) | 3072 AR5K_TXPOWER_CCK(8, 0), AR5K_PHY_TXPOWER_RATE3); 3073 3074 ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(14, 24) | 3075 AR5K_TXPOWER_CCK(13, 16) | AR5K_TXPOWER_CCK(12, 8) | 3076 AR5K_TXPOWER_CCK(11, 0), AR5K_PHY_TXPOWER_RATE4); 3077 3078 /* FIXME: TPC support */ 3079 if (ah->ah_txpower.txp_tpc) { 3080 ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX_TPC_ENABLE | 3081 AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX); 3082 3083 ath5k_hw_reg_write(ah, 3084 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_ACK) | 3085 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CTS) | 3086 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CHIRP), 3087 AR5K_TPC); 3088 } else { 3089 ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX | 3090 AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX); 3091 } 3092 3093 return 0; 3094} 3095 3096int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower) 3097{ 3098 /*Just a try M.F.*/ 3099 struct ieee80211_channel *channel = ah->ah_current_channel; 3100 u8 ee_mode; 3101 3102 ATH5K_TRACE(ah->ah_sc); 3103 3104 switch (channel->hw_value & CHANNEL_MODES) { 3105 case CHANNEL_A: 3106 case CHANNEL_T: 3107 case CHANNEL_XR: 3108 ee_mode = AR5K_EEPROM_MODE_11A; 3109 break; 3110 case CHANNEL_G: 3111 case CHANNEL_TG: 3112 ee_mode = AR5K_EEPROM_MODE_11G; 3113 break; 3114 case CHANNEL_B: 3115 ee_mode = AR5K_EEPROM_MODE_11B; 3116 break; 3117 default: 3118 ATH5K_ERR(ah->ah_sc, 3119 "invalid channel: %d\n", channel->center_freq); 3120 return -EINVAL; 3121 } 3122 3123 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_TXPOWER, 3124 "changing txpower to %d\n", txpower); 3125 3126 return ath5k_hw_txpower(ah, channel, ee_mode, txpower); 3127} 3128