phy.c revision 230fc4f3b2fa72980787a5f86c850f02bb193187
1/* 2 * PHY functions 3 * 4 * Copyright (c) 2004-2007 Reyk Floeter <reyk@openbsd.org> 5 * Copyright (c) 2006-2009 Nick Kossifidis <mickflemm@gmail.com> 6 * Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com> 7 * Copyright (c) 2008-2009 Felix Fietkau <nbd@openwrt.org> 8 * 9 * Permission to use, copy, modify, and distribute this software for any 10 * purpose with or without fee is hereby granted, provided that the above 11 * copyright notice and this permission notice appear in all copies. 12 * 13 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES 14 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF 15 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR 16 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES 17 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN 18 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF 19 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. 20 * 21 */ 22 23#include <linux/delay.h> 24#include <linux/slab.h> 25 26#include "ath5k.h" 27#include "reg.h" 28#include "base.h" 29#include "rfbuffer.h" 30#include "rfgain.h" 31 32/* 33 * Used to modify RF Banks before writing them to AR5K_RF_BUFFER 34 */ 35static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah, 36 const struct ath5k_rf_reg *rf_regs, 37 u32 val, u8 reg_id, bool set) 38{ 39 const struct ath5k_rf_reg *rfreg = NULL; 40 u8 offset, bank, num_bits, col, position; 41 u16 entry; 42 u32 mask, data, last_bit, bits_shifted, first_bit; 43 u32 *rfb; 44 s32 bits_left; 45 int i; 46 47 data = 0; 48 rfb = ah->ah_rf_banks; 49 50 for (i = 0; i < ah->ah_rf_regs_count; i++) { 51 if (rf_regs[i].index == reg_id) { 52 rfreg = &rf_regs[i]; 53 break; 54 } 55 } 56 57 if (rfb == NULL || rfreg == NULL) { 58 ATH5K_PRINTF("Rf register not found!\n"); 59 /* should not happen */ 60 return 0; 61 } 62 63 bank = rfreg->bank; 64 num_bits = rfreg->field.len; 65 first_bit = rfreg->field.pos; 66 col = rfreg->field.col; 67 68 /* first_bit is an offset from bank's 69 * start. Since we have all banks on 70 * the same array, we use this offset 71 * to mark each bank's start */ 72 offset = ah->ah_offset[bank]; 73 74 /* Boundary check */ 75 if (!(col <= 3 && num_bits <= 32 && first_bit + num_bits <= 319)) { 76 ATH5K_PRINTF("invalid values at offset %u\n", offset); 77 return 0; 78 } 79 80 entry = ((first_bit - 1) / 8) + offset; 81 position = (first_bit - 1) % 8; 82 83 if (set) 84 data = ath5k_hw_bitswap(val, num_bits); 85 86 for (bits_shifted = 0, bits_left = num_bits; bits_left > 0; 87 position = 0, entry++) { 88 89 last_bit = (position + bits_left > 8) ? 8 : 90 position + bits_left; 91 92 mask = (((1 << last_bit) - 1) ^ ((1 << position) - 1)) << 93 (col * 8); 94 95 if (set) { 96 rfb[entry] &= ~mask; 97 rfb[entry] |= ((data << position) << (col * 8)) & mask; 98 data >>= (8 - position); 99 } else { 100 data |= (((rfb[entry] & mask) >> (col * 8)) >> position) 101 << bits_shifted; 102 bits_shifted += last_bit - position; 103 } 104 105 bits_left -= 8 - position; 106 } 107 108 data = set ? 1 : ath5k_hw_bitswap(data, num_bits); 109 110 return data; 111} 112 113/**********************\ 114* RF Gain optimization * 115\**********************/ 116 117/* 118 * This code is used to optimize rf gain on different environments 119 * (temperature mostly) based on feedback from a power detector. 120 * 121 * It's only used on RF5111 and RF5112, later RF chips seem to have 122 * auto adjustment on hw -notice they have a much smaller BANK 7 and 123 * no gain optimization ladder-. 124 * 125 * For more infos check out this patent doc 126 * http://www.freepatentsonline.com/7400691.html 127 * 128 * This paper describes power drops as seen on the receiver due to 129 * probe packets 130 * http://www.cnri.dit.ie/publications/ICT08%20-%20Practical%20Issues 131 * %20of%20Power%20Control.pdf 132 * 133 * And this is the MadWiFi bug entry related to the above 134 * http://madwifi-project.org/ticket/1659 135 * with various measurements and diagrams 136 * 137 * TODO: Deal with power drops due to probes by setting an apropriate 138 * tx power on the probe packets ! Make this part of the calibration process. 139 */ 140 141/* Initialize ah_gain durring attach */ 142int ath5k_hw_rfgain_opt_init(struct ath5k_hw *ah) 143{ 144 /* Initialize the gain optimization values */ 145 switch (ah->ah_radio) { 146 case AR5K_RF5111: 147 ah->ah_gain.g_step_idx = rfgain_opt_5111.go_default; 148 ah->ah_gain.g_low = 20; 149 ah->ah_gain.g_high = 35; 150 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 151 break; 152 case AR5K_RF5112: 153 ah->ah_gain.g_step_idx = rfgain_opt_5112.go_default; 154 ah->ah_gain.g_low = 20; 155 ah->ah_gain.g_high = 85; 156 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 157 break; 158 default: 159 return -EINVAL; 160 } 161 162 return 0; 163} 164 165/* Schedule a gain probe check on the next transmited packet. 166 * That means our next packet is going to be sent with lower 167 * tx power and a Peak to Average Power Detector (PAPD) will try 168 * to measure the gain. 169 * 170 * XXX: How about forcing a tx packet (bypassing PCU arbitrator etc) 171 * just after we enable the probe so that we don't mess with 172 * standard traffic ? Maybe it's time to use sw interrupts and 173 * a probe tasklet !!! 174 */ 175static void ath5k_hw_request_rfgain_probe(struct ath5k_hw *ah) 176{ 177 178 /* Skip if gain calibration is inactive or 179 * we already handle a probe request */ 180 if (ah->ah_gain.g_state != AR5K_RFGAIN_ACTIVE) 181 return; 182 183 /* Send the packet with 2dB below max power as 184 * patent doc suggest */ 185 ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txpower.txp_ofdm - 4, 186 AR5K_PHY_PAPD_PROBE_TXPOWER) | 187 AR5K_PHY_PAPD_PROBE_TX_NEXT, AR5K_PHY_PAPD_PROBE); 188 189 ah->ah_gain.g_state = AR5K_RFGAIN_READ_REQUESTED; 190 191} 192 193/* Calculate gain_F measurement correction 194 * based on the current step for RF5112 rev. 2 */ 195static u32 ath5k_hw_rf_gainf_corr(struct ath5k_hw *ah) 196{ 197 u32 mix, step; 198 u32 *rf; 199 const struct ath5k_gain_opt *go; 200 const struct ath5k_gain_opt_step *g_step; 201 const struct ath5k_rf_reg *rf_regs; 202 203 /* Only RF5112 Rev. 2 supports it */ 204 if ((ah->ah_radio != AR5K_RF5112) || 205 (ah->ah_radio_5ghz_revision <= AR5K_SREV_RAD_5112A)) 206 return 0; 207 208 go = &rfgain_opt_5112; 209 rf_regs = rf_regs_5112a; 210 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a); 211 212 g_step = &go->go_step[ah->ah_gain.g_step_idx]; 213 214 if (ah->ah_rf_banks == NULL) 215 return 0; 216 217 rf = ah->ah_rf_banks; 218 ah->ah_gain.g_f_corr = 0; 219 220 /* No VGA (Variable Gain Amplifier) override, skip */ 221 if (ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, false) != 1) 222 return 0; 223 224 /* Mix gain stepping */ 225 step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXGAIN_STEP, false); 226 227 /* Mix gain override */ 228 mix = g_step->gos_param[0]; 229 230 switch (mix) { 231 case 3: 232 ah->ah_gain.g_f_corr = step * 2; 233 break; 234 case 2: 235 ah->ah_gain.g_f_corr = (step - 5) * 2; 236 break; 237 case 1: 238 ah->ah_gain.g_f_corr = step; 239 break; 240 default: 241 ah->ah_gain.g_f_corr = 0; 242 break; 243 } 244 245 return ah->ah_gain.g_f_corr; 246} 247 248/* Check if current gain_F measurement is in the range of our 249 * power detector windows. If we get a measurement outside range 250 * we know it's not accurate (detectors can't measure anything outside 251 * their detection window) so we must ignore it */ 252static bool ath5k_hw_rf_check_gainf_readback(struct ath5k_hw *ah) 253{ 254 const struct ath5k_rf_reg *rf_regs; 255 u32 step, mix_ovr, level[4]; 256 u32 *rf; 257 258 if (ah->ah_rf_banks == NULL) 259 return false; 260 261 rf = ah->ah_rf_banks; 262 263 if (ah->ah_radio == AR5K_RF5111) { 264 265 rf_regs = rf_regs_5111; 266 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111); 267 268 step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_RFGAIN_STEP, 269 false); 270 271 level[0] = 0; 272 level[1] = (step == 63) ? 50 : step + 4; 273 level[2] = (step != 63) ? 64 : level[0]; 274 level[3] = level[2] + 50 ; 275 276 ah->ah_gain.g_high = level[3] - 277 (step == 63 ? AR5K_GAIN_DYN_ADJUST_HI_MARGIN : -5); 278 ah->ah_gain.g_low = level[0] + 279 (step == 63 ? AR5K_GAIN_DYN_ADJUST_LO_MARGIN : 0); 280 } else { 281 282 rf_regs = rf_regs_5112; 283 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112); 284 285 mix_ovr = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, 286 false); 287 288 level[0] = level[2] = 0; 289 290 if (mix_ovr == 1) { 291 level[1] = level[3] = 83; 292 } else { 293 level[1] = level[3] = 107; 294 ah->ah_gain.g_high = 55; 295 } 296 } 297 298 return (ah->ah_gain.g_current >= level[0] && 299 ah->ah_gain.g_current <= level[1]) || 300 (ah->ah_gain.g_current >= level[2] && 301 ah->ah_gain.g_current <= level[3]); 302} 303 304/* Perform gain_F adjustment by choosing the right set 305 * of parameters from rf gain optimization ladder */ 306static s8 ath5k_hw_rf_gainf_adjust(struct ath5k_hw *ah) 307{ 308 const struct ath5k_gain_opt *go; 309 const struct ath5k_gain_opt_step *g_step; 310 int ret = 0; 311 312 switch (ah->ah_radio) { 313 case AR5K_RF5111: 314 go = &rfgain_opt_5111; 315 break; 316 case AR5K_RF5112: 317 go = &rfgain_opt_5112; 318 break; 319 default: 320 return 0; 321 } 322 323 g_step = &go->go_step[ah->ah_gain.g_step_idx]; 324 325 if (ah->ah_gain.g_current >= ah->ah_gain.g_high) { 326 327 /* Reached maximum */ 328 if (ah->ah_gain.g_step_idx == 0) 329 return -1; 330 331 for (ah->ah_gain.g_target = ah->ah_gain.g_current; 332 ah->ah_gain.g_target >= ah->ah_gain.g_high && 333 ah->ah_gain.g_step_idx > 0; 334 g_step = &go->go_step[ah->ah_gain.g_step_idx]) 335 ah->ah_gain.g_target -= 2 * 336 (go->go_step[--(ah->ah_gain.g_step_idx)].gos_gain - 337 g_step->gos_gain); 338 339 ret = 1; 340 goto done; 341 } 342 343 if (ah->ah_gain.g_current <= ah->ah_gain.g_low) { 344 345 /* Reached minimum */ 346 if (ah->ah_gain.g_step_idx == (go->go_steps_count - 1)) 347 return -2; 348 349 for (ah->ah_gain.g_target = ah->ah_gain.g_current; 350 ah->ah_gain.g_target <= ah->ah_gain.g_low && 351 ah->ah_gain.g_step_idx < go->go_steps_count-1; 352 g_step = &go->go_step[ah->ah_gain.g_step_idx]) 353 ah->ah_gain.g_target -= 2 * 354 (go->go_step[++ah->ah_gain.g_step_idx].gos_gain - 355 g_step->gos_gain); 356 357 ret = 2; 358 goto done; 359 } 360 361done: 362 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 363 "ret %d, gain step %u, current gain %u, target gain %u\n", 364 ret, ah->ah_gain.g_step_idx, ah->ah_gain.g_current, 365 ah->ah_gain.g_target); 366 367 return ret; 368} 369 370/* Main callback for thermal rf gain calibration engine 371 * Check for a new gain reading and schedule an adjustment 372 * if needed. 373 * 374 * TODO: Use sw interrupt to schedule reset if gain_F needs 375 * adjustment */ 376enum ath5k_rfgain ath5k_hw_gainf_calibrate(struct ath5k_hw *ah) 377{ 378 u32 data, type; 379 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 380 381 if (ah->ah_rf_banks == NULL || 382 ah->ah_gain.g_state == AR5K_RFGAIN_INACTIVE) 383 return AR5K_RFGAIN_INACTIVE; 384 385 /* No check requested, either engine is inactive 386 * or an adjustment is already requested */ 387 if (ah->ah_gain.g_state != AR5K_RFGAIN_READ_REQUESTED) 388 goto done; 389 390 /* Read the PAPD (Peak to Average Power Detector) 391 * register */ 392 data = ath5k_hw_reg_read(ah, AR5K_PHY_PAPD_PROBE); 393 394 /* No probe is scheduled, read gain_F measurement */ 395 if (!(data & AR5K_PHY_PAPD_PROBE_TX_NEXT)) { 396 ah->ah_gain.g_current = data >> AR5K_PHY_PAPD_PROBE_GAINF_S; 397 type = AR5K_REG_MS(data, AR5K_PHY_PAPD_PROBE_TYPE); 398 399 /* If tx packet is CCK correct the gain_F measurement 400 * by cck ofdm gain delta */ 401 if (type == AR5K_PHY_PAPD_PROBE_TYPE_CCK) { 402 if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) 403 ah->ah_gain.g_current += 404 ee->ee_cck_ofdm_gain_delta; 405 else 406 ah->ah_gain.g_current += 407 AR5K_GAIN_CCK_PROBE_CORR; 408 } 409 410 /* Further correct gain_F measurement for 411 * RF5112A radios */ 412 if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) { 413 ath5k_hw_rf_gainf_corr(ah); 414 ah->ah_gain.g_current = 415 ah->ah_gain.g_current >= ah->ah_gain.g_f_corr ? 416 (ah->ah_gain.g_current-ah->ah_gain.g_f_corr) : 417 0; 418 } 419 420 /* Check if measurement is ok and if we need 421 * to adjust gain, schedule a gain adjustment, 422 * else switch back to the acive state */ 423 if (ath5k_hw_rf_check_gainf_readback(ah) && 424 AR5K_GAIN_CHECK_ADJUST(&ah->ah_gain) && 425 ath5k_hw_rf_gainf_adjust(ah)) { 426 ah->ah_gain.g_state = AR5K_RFGAIN_NEED_CHANGE; 427 } else { 428 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 429 } 430 } 431 432done: 433 return ah->ah_gain.g_state; 434} 435 436/* Write initial rf gain table to set the RF sensitivity 437 * this one works on all RF chips and has nothing to do 438 * with gain_F calibration */ 439int ath5k_hw_rfgain_init(struct ath5k_hw *ah, unsigned int freq) 440{ 441 const struct ath5k_ini_rfgain *ath5k_rfg; 442 unsigned int i, size; 443 444 switch (ah->ah_radio) { 445 case AR5K_RF5111: 446 ath5k_rfg = rfgain_5111; 447 size = ARRAY_SIZE(rfgain_5111); 448 break; 449 case AR5K_RF5112: 450 ath5k_rfg = rfgain_5112; 451 size = ARRAY_SIZE(rfgain_5112); 452 break; 453 case AR5K_RF2413: 454 ath5k_rfg = rfgain_2413; 455 size = ARRAY_SIZE(rfgain_2413); 456 break; 457 case AR5K_RF2316: 458 ath5k_rfg = rfgain_2316; 459 size = ARRAY_SIZE(rfgain_2316); 460 break; 461 case AR5K_RF5413: 462 ath5k_rfg = rfgain_5413; 463 size = ARRAY_SIZE(rfgain_5413); 464 break; 465 case AR5K_RF2317: 466 case AR5K_RF2425: 467 ath5k_rfg = rfgain_2425; 468 size = ARRAY_SIZE(rfgain_2425); 469 break; 470 default: 471 return -EINVAL; 472 } 473 474 switch (freq) { 475 case AR5K_INI_RFGAIN_2GHZ: 476 case AR5K_INI_RFGAIN_5GHZ: 477 break; 478 default: 479 return -EINVAL; 480 } 481 482 for (i = 0; i < size; i++) { 483 AR5K_REG_WAIT(i); 484 ath5k_hw_reg_write(ah, ath5k_rfg[i].rfg_value[freq], 485 (u32)ath5k_rfg[i].rfg_register); 486 } 487 488 return 0; 489} 490 491 492 493/********************\ 494* RF Registers setup * 495\********************/ 496 497 498/* 499 * Setup RF registers by writing rf buffer on hw 500 */ 501int ath5k_hw_rfregs_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, 502 unsigned int mode) 503{ 504 const struct ath5k_rf_reg *rf_regs; 505 const struct ath5k_ini_rfbuffer *ini_rfb; 506 const struct ath5k_gain_opt *go = NULL; 507 const struct ath5k_gain_opt_step *g_step; 508 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 509 u8 ee_mode = 0; 510 u32 *rfb; 511 int i, obdb = -1, bank = -1; 512 513 switch (ah->ah_radio) { 514 case AR5K_RF5111: 515 rf_regs = rf_regs_5111; 516 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111); 517 ini_rfb = rfb_5111; 518 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5111); 519 go = &rfgain_opt_5111; 520 break; 521 case AR5K_RF5112: 522 if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) { 523 rf_regs = rf_regs_5112a; 524 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a); 525 ini_rfb = rfb_5112a; 526 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112a); 527 } else { 528 rf_regs = rf_regs_5112; 529 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112); 530 ini_rfb = rfb_5112; 531 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112); 532 } 533 go = &rfgain_opt_5112; 534 break; 535 case AR5K_RF2413: 536 rf_regs = rf_regs_2413; 537 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2413); 538 ini_rfb = rfb_2413; 539 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2413); 540 break; 541 case AR5K_RF2316: 542 rf_regs = rf_regs_2316; 543 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2316); 544 ini_rfb = rfb_2316; 545 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2316); 546 break; 547 case AR5K_RF5413: 548 rf_regs = rf_regs_5413; 549 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5413); 550 ini_rfb = rfb_5413; 551 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5413); 552 break; 553 case AR5K_RF2317: 554 rf_regs = rf_regs_2425; 555 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425); 556 ini_rfb = rfb_2317; 557 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2317); 558 break; 559 case AR5K_RF2425: 560 rf_regs = rf_regs_2425; 561 ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425); 562 if (ah->ah_mac_srev < AR5K_SREV_AR2417) { 563 ini_rfb = rfb_2425; 564 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2425); 565 } else { 566 ini_rfb = rfb_2417; 567 ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2417); 568 } 569 break; 570 default: 571 return -EINVAL; 572 } 573 574 /* If it's the first time we set rf buffer, allocate 575 * ah->ah_rf_banks based on ah->ah_rf_banks_size 576 * we set above */ 577 if (ah->ah_rf_banks == NULL) { 578 ah->ah_rf_banks = kmalloc(sizeof(u32) * ah->ah_rf_banks_size, 579 GFP_KERNEL); 580 if (ah->ah_rf_banks == NULL) { 581 ATH5K_ERR(ah->ah_sc, "out of memory\n"); 582 return -ENOMEM; 583 } 584 } 585 586 /* Copy values to modify them */ 587 rfb = ah->ah_rf_banks; 588 589 for (i = 0; i < ah->ah_rf_banks_size; i++) { 590 if (ini_rfb[i].rfb_bank >= AR5K_MAX_RF_BANKS) { 591 ATH5K_ERR(ah->ah_sc, "invalid bank\n"); 592 return -EINVAL; 593 } 594 595 /* Bank changed, write down the offset */ 596 if (bank != ini_rfb[i].rfb_bank) { 597 bank = ini_rfb[i].rfb_bank; 598 ah->ah_offset[bank] = i; 599 } 600 601 rfb[i] = ini_rfb[i].rfb_mode_data[mode]; 602 } 603 604 /* Set Output and Driver bias current (OB/DB) */ 605 if (channel->hw_value & CHANNEL_2GHZ) { 606 607 if (channel->hw_value & CHANNEL_CCK) 608 ee_mode = AR5K_EEPROM_MODE_11B; 609 else 610 ee_mode = AR5K_EEPROM_MODE_11G; 611 612 /* For RF511X/RF211X combination we 613 * use b_OB and b_DB parameters stored 614 * in eeprom on ee->ee_ob[ee_mode][0] 615 * 616 * For all other chips we use OB/DB for 2Ghz 617 * stored in the b/g modal section just like 618 * 802.11a on ee->ee_ob[ee_mode][1] */ 619 if ((ah->ah_radio == AR5K_RF5111) || 620 (ah->ah_radio == AR5K_RF5112)) 621 obdb = 0; 622 else 623 obdb = 1; 624 625 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb], 626 AR5K_RF_OB_2GHZ, true); 627 628 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb], 629 AR5K_RF_DB_2GHZ, true); 630 631 /* RF5111 always needs OB/DB for 5GHz, even if we use 2GHz */ 632 } else if ((channel->hw_value & CHANNEL_5GHZ) || 633 (ah->ah_radio == AR5K_RF5111)) { 634 635 /* For 11a, Turbo and XR we need to choose 636 * OB/DB based on frequency range */ 637 ee_mode = AR5K_EEPROM_MODE_11A; 638 obdb = channel->center_freq >= 5725 ? 3 : 639 (channel->center_freq >= 5500 ? 2 : 640 (channel->center_freq >= 5260 ? 1 : 641 (channel->center_freq > 4000 ? 0 : -1))); 642 643 if (obdb < 0) 644 return -EINVAL; 645 646 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb], 647 AR5K_RF_OB_5GHZ, true); 648 649 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb], 650 AR5K_RF_DB_5GHZ, true); 651 } 652 653 g_step = &go->go_step[ah->ah_gain.g_step_idx]; 654 655 /* Bank Modifications (chip-specific) */ 656 if (ah->ah_radio == AR5K_RF5111) { 657 658 /* Set gain_F settings according to current step */ 659 if (channel->hw_value & CHANNEL_OFDM) { 660 661 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_FRAME_CTL, 662 AR5K_PHY_FRAME_CTL_TX_CLIP, 663 g_step->gos_param[0]); 664 665 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1], 666 AR5K_RF_PWD_90, true); 667 668 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2], 669 AR5K_RF_PWD_84, true); 670 671 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3], 672 AR5K_RF_RFGAIN_SEL, true); 673 674 /* We programmed gain_F parameters, switch back 675 * to active state */ 676 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 677 678 } 679 680 /* Bank 6/7 setup */ 681 682 ath5k_hw_rfb_op(ah, rf_regs, !ee->ee_xpd[ee_mode], 683 AR5K_RF_PWD_XPD, true); 684 685 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_x_gain[ee_mode], 686 AR5K_RF_XPD_GAIN, true); 687 688 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode], 689 AR5K_RF_GAIN_I, true); 690 691 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode], 692 AR5K_RF_PLO_SEL, true); 693 694 /* TODO: Half/quarter channel support */ 695 } 696 697 if (ah->ah_radio == AR5K_RF5112) { 698 699 /* Set gain_F settings according to current step */ 700 if (channel->hw_value & CHANNEL_OFDM) { 701 702 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[0], 703 AR5K_RF_MIXGAIN_OVR, true); 704 705 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1], 706 AR5K_RF_PWD_138, true); 707 708 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2], 709 AR5K_RF_PWD_137, true); 710 711 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3], 712 AR5K_RF_PWD_136, true); 713 714 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[4], 715 AR5K_RF_PWD_132, true); 716 717 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[5], 718 AR5K_RF_PWD_131, true); 719 720 ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[6], 721 AR5K_RF_PWD_130, true); 722 723 /* We programmed gain_F parameters, switch back 724 * to active state */ 725 ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; 726 } 727 728 /* Bank 6/7 setup */ 729 730 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode], 731 AR5K_RF_XPD_SEL, true); 732 733 if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112A) { 734 /* Rev. 1 supports only one xpd */ 735 ath5k_hw_rfb_op(ah, rf_regs, 736 ee->ee_x_gain[ee_mode], 737 AR5K_RF_XPD_GAIN, true); 738 739 } else { 740 u8 *pdg_curve_to_idx = ee->ee_pdc_to_idx[ee_mode]; 741 if (ee->ee_pd_gains[ee_mode] > 1) { 742 ath5k_hw_rfb_op(ah, rf_regs, 743 pdg_curve_to_idx[0], 744 AR5K_RF_PD_GAIN_LO, true); 745 ath5k_hw_rfb_op(ah, rf_regs, 746 pdg_curve_to_idx[1], 747 AR5K_RF_PD_GAIN_HI, true); 748 } else { 749 ath5k_hw_rfb_op(ah, rf_regs, 750 pdg_curve_to_idx[0], 751 AR5K_RF_PD_GAIN_LO, true); 752 ath5k_hw_rfb_op(ah, rf_regs, 753 pdg_curve_to_idx[0], 754 AR5K_RF_PD_GAIN_HI, true); 755 } 756 757 /* Lower synth voltage on Rev 2 */ 758 ath5k_hw_rfb_op(ah, rf_regs, 2, 759 AR5K_RF_HIGH_VC_CP, true); 760 761 ath5k_hw_rfb_op(ah, rf_regs, 2, 762 AR5K_RF_MID_VC_CP, true); 763 764 ath5k_hw_rfb_op(ah, rf_regs, 2, 765 AR5K_RF_LOW_VC_CP, true); 766 767 ath5k_hw_rfb_op(ah, rf_regs, 2, 768 AR5K_RF_PUSH_UP, true); 769 770 /* Decrease power consumption on 5213+ BaseBand */ 771 if (ah->ah_phy_revision >= AR5K_SREV_PHY_5212A) { 772 ath5k_hw_rfb_op(ah, rf_regs, 1, 773 AR5K_RF_PAD2GND, true); 774 775 ath5k_hw_rfb_op(ah, rf_regs, 1, 776 AR5K_RF_XB2_LVL, true); 777 778 ath5k_hw_rfb_op(ah, rf_regs, 1, 779 AR5K_RF_XB5_LVL, true); 780 781 ath5k_hw_rfb_op(ah, rf_regs, 1, 782 AR5K_RF_PWD_167, true); 783 784 ath5k_hw_rfb_op(ah, rf_regs, 1, 785 AR5K_RF_PWD_166, true); 786 } 787 } 788 789 ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode], 790 AR5K_RF_GAIN_I, true); 791 792 /* TODO: Half/quarter channel support */ 793 794 } 795 796 if (ah->ah_radio == AR5K_RF5413 && 797 channel->hw_value & CHANNEL_2GHZ) { 798 799 ath5k_hw_rfb_op(ah, rf_regs, 1, AR5K_RF_DERBY_CHAN_SEL_MODE, 800 true); 801 802 /* Set optimum value for early revisions (on pci-e chips) */ 803 if (ah->ah_mac_srev >= AR5K_SREV_AR5424 && 804 ah->ah_mac_srev < AR5K_SREV_AR5413) 805 ath5k_hw_rfb_op(ah, rf_regs, ath5k_hw_bitswap(6, 3), 806 AR5K_RF_PWD_ICLOBUF_2G, true); 807 808 } 809 810 /* Write RF banks on hw */ 811 for (i = 0; i < ah->ah_rf_banks_size; i++) { 812 AR5K_REG_WAIT(i); 813 ath5k_hw_reg_write(ah, rfb[i], ini_rfb[i].rfb_ctrl_register); 814 } 815 816 return 0; 817} 818 819 820/**************************\ 821 PHY/RF channel functions 822\**************************/ 823 824/* 825 * Check if a channel is supported 826 */ 827bool ath5k_channel_ok(struct ath5k_hw *ah, u16 freq, unsigned int flags) 828{ 829 /* Check if the channel is in our supported range */ 830 if (flags & CHANNEL_2GHZ) { 831 if ((freq >= ah->ah_capabilities.cap_range.range_2ghz_min) && 832 (freq <= ah->ah_capabilities.cap_range.range_2ghz_max)) 833 return true; 834 } else if (flags & CHANNEL_5GHZ) 835 if ((freq >= ah->ah_capabilities.cap_range.range_5ghz_min) && 836 (freq <= ah->ah_capabilities.cap_range.range_5ghz_max)) 837 return true; 838 839 return false; 840} 841 842/* 843 * Convertion needed for RF5110 844 */ 845static u32 ath5k_hw_rf5110_chan2athchan(struct ieee80211_channel *channel) 846{ 847 u32 athchan; 848 849 /* 850 * Convert IEEE channel/MHz to an internal channel value used 851 * by the AR5210 chipset. This has not been verified with 852 * newer chipsets like the AR5212A who have a completely 853 * different RF/PHY part. 854 */ 855 athchan = (ath5k_hw_bitswap( 856 (ieee80211_frequency_to_channel( 857 channel->center_freq) - 24) / 2, 5) 858 << 1) | (1 << 6) | 0x1; 859 return athchan; 860} 861 862/* 863 * Set channel on RF5110 864 */ 865static int ath5k_hw_rf5110_channel(struct ath5k_hw *ah, 866 struct ieee80211_channel *channel) 867{ 868 u32 data; 869 870 /* 871 * Set the channel and wait 872 */ 873 data = ath5k_hw_rf5110_chan2athchan(channel); 874 ath5k_hw_reg_write(ah, data, AR5K_RF_BUFFER); 875 ath5k_hw_reg_write(ah, 0, AR5K_RF_BUFFER_CONTROL_0); 876 mdelay(1); 877 878 return 0; 879} 880 881/* 882 * Convertion needed for 5111 883 */ 884static int ath5k_hw_rf5111_chan2athchan(unsigned int ieee, 885 struct ath5k_athchan_2ghz *athchan) 886{ 887 int channel; 888 889 /* Cast this value to catch negative channel numbers (>= -19) */ 890 channel = (int)ieee; 891 892 /* 893 * Map 2GHz IEEE channel to 5GHz Atheros channel 894 */ 895 if (channel <= 13) { 896 athchan->a2_athchan = 115 + channel; 897 athchan->a2_flags = 0x46; 898 } else if (channel == 14) { 899 athchan->a2_athchan = 124; 900 athchan->a2_flags = 0x44; 901 } else if (channel >= 15 && channel <= 26) { 902 athchan->a2_athchan = ((channel - 14) * 4) + 132; 903 athchan->a2_flags = 0x46; 904 } else 905 return -EINVAL; 906 907 return 0; 908} 909 910/* 911 * Set channel on 5111 912 */ 913static int ath5k_hw_rf5111_channel(struct ath5k_hw *ah, 914 struct ieee80211_channel *channel) 915{ 916 struct ath5k_athchan_2ghz ath5k_channel_2ghz; 917 unsigned int ath5k_channel = 918 ieee80211_frequency_to_channel(channel->center_freq); 919 u32 data0, data1, clock; 920 int ret; 921 922 /* 923 * Set the channel on the RF5111 radio 924 */ 925 data0 = data1 = 0; 926 927 if (channel->hw_value & CHANNEL_2GHZ) { 928 /* Map 2GHz channel to 5GHz Atheros channel ID */ 929 ret = ath5k_hw_rf5111_chan2athchan( 930 ieee80211_frequency_to_channel(channel->center_freq), 931 &ath5k_channel_2ghz); 932 if (ret) 933 return ret; 934 935 ath5k_channel = ath5k_channel_2ghz.a2_athchan; 936 data0 = ((ath5k_hw_bitswap(ath5k_channel_2ghz.a2_flags, 8) & 0xff) 937 << 5) | (1 << 4); 938 } 939 940 if (ath5k_channel < 145 || !(ath5k_channel & 1)) { 941 clock = 1; 942 data1 = ((ath5k_hw_bitswap(ath5k_channel - 24, 8) & 0xff) << 2) | 943 (clock << 1) | (1 << 10) | 1; 944 } else { 945 clock = 0; 946 data1 = ((ath5k_hw_bitswap((ath5k_channel - 24) / 2, 8) & 0xff) 947 << 2) | (clock << 1) | (1 << 10) | 1; 948 } 949 950 ath5k_hw_reg_write(ah, (data1 & 0xff) | ((data0 & 0xff) << 8), 951 AR5K_RF_BUFFER); 952 ath5k_hw_reg_write(ah, ((data1 >> 8) & 0xff) | (data0 & 0xff00), 953 AR5K_RF_BUFFER_CONTROL_3); 954 955 return 0; 956} 957 958/* 959 * Set channel on 5112 and newer 960 */ 961static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah, 962 struct ieee80211_channel *channel) 963{ 964 u32 data, data0, data1, data2; 965 u16 c; 966 967 data = data0 = data1 = data2 = 0; 968 c = channel->center_freq; 969 970 if (c < 4800) { 971 if (!((c - 2224) % 5)) { 972 data0 = ((2 * (c - 704)) - 3040) / 10; 973 data1 = 1; 974 } else if (!((c - 2192) % 5)) { 975 data0 = ((2 * (c - 672)) - 3040) / 10; 976 data1 = 0; 977 } else 978 return -EINVAL; 979 980 data0 = ath5k_hw_bitswap((data0 << 2) & 0xff, 8); 981 } else if ((c % 5) != 2 || c > 5435) { 982 if (!(c % 20) && c >= 5120) { 983 data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); 984 data2 = ath5k_hw_bitswap(3, 2); 985 } else if (!(c % 10)) { 986 data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); 987 data2 = ath5k_hw_bitswap(2, 2); 988 } else if (!(c % 5)) { 989 data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); 990 data2 = ath5k_hw_bitswap(1, 2); 991 } else 992 return -EINVAL; 993 } else { 994 data0 = ath5k_hw_bitswap((10 * (c - 2 - 4800)) / 25 + 1, 8); 995 data2 = ath5k_hw_bitswap(0, 2); 996 } 997 998 data = (data0 << 4) | (data1 << 1) | (data2 << 2) | 0x1001; 999 1000 ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); 1001 ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); 1002 1003 return 0; 1004} 1005 1006/* 1007 * Set the channel on the RF2425 1008 */ 1009static int ath5k_hw_rf2425_channel(struct ath5k_hw *ah, 1010 struct ieee80211_channel *channel) 1011{ 1012 u32 data, data0, data2; 1013 u16 c; 1014 1015 data = data0 = data2 = 0; 1016 c = channel->center_freq; 1017 1018 if (c < 4800) { 1019 data0 = ath5k_hw_bitswap((c - 2272), 8); 1020 data2 = 0; 1021 /* ? 5GHz ? */ 1022 } else if ((c % 5) != 2 || c > 5435) { 1023 if (!(c % 20) && c < 5120) 1024 data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); 1025 else if (!(c % 10)) 1026 data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); 1027 else if (!(c % 5)) 1028 data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); 1029 else 1030 return -EINVAL; 1031 data2 = ath5k_hw_bitswap(1, 2); 1032 } else { 1033 data0 = ath5k_hw_bitswap((10 * (c - 2 - 4800)) / 25 + 1, 8); 1034 data2 = ath5k_hw_bitswap(0, 2); 1035 } 1036 1037 data = (data0 << 4) | data2 << 2 | 0x1001; 1038 1039 ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); 1040 ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); 1041 1042 return 0; 1043} 1044 1045/* 1046 * Set a channel on the radio chip 1047 */ 1048int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel) 1049{ 1050 int ret; 1051 /* 1052 * Check bounds supported by the PHY (we don't care about regultory 1053 * restrictions at this point). Note: hw_value already has the band 1054 * (CHANNEL_2GHZ, or CHANNEL_5GHZ) so we inform ath5k_channel_ok() 1055 * of the band by that */ 1056 if (!ath5k_channel_ok(ah, channel->center_freq, channel->hw_value)) { 1057 ATH5K_ERR(ah->ah_sc, 1058 "channel frequency (%u MHz) out of supported " 1059 "band range\n", 1060 channel->center_freq); 1061 return -EINVAL; 1062 } 1063 1064 /* 1065 * Set the channel and wait 1066 */ 1067 switch (ah->ah_radio) { 1068 case AR5K_RF5110: 1069 ret = ath5k_hw_rf5110_channel(ah, channel); 1070 break; 1071 case AR5K_RF5111: 1072 ret = ath5k_hw_rf5111_channel(ah, channel); 1073 break; 1074 case AR5K_RF2425: 1075 ret = ath5k_hw_rf2425_channel(ah, channel); 1076 break; 1077 default: 1078 ret = ath5k_hw_rf5112_channel(ah, channel); 1079 break; 1080 } 1081 1082 if (ret) 1083 return ret; 1084 1085 /* Set JAPAN setting for channel 14 */ 1086 if (channel->center_freq == 2484) { 1087 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, 1088 AR5K_PHY_CCKTXCTL_JAPAN); 1089 } else { 1090 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, 1091 AR5K_PHY_CCKTXCTL_WORLD); 1092 } 1093 1094 ah->ah_current_channel = channel; 1095 ah->ah_turbo = channel->hw_value == CHANNEL_T ? true : false; 1096 1097 return 0; 1098} 1099 1100/*****************\ 1101 PHY calibration 1102\*****************/ 1103 1104static int sign_extend(int val, const int nbits) 1105{ 1106 int order = BIT(nbits-1); 1107 return (val ^ order) - order; 1108} 1109 1110static s32 ath5k_hw_read_measured_noise_floor(struct ath5k_hw *ah) 1111{ 1112 s32 val; 1113 1114 val = ath5k_hw_reg_read(ah, AR5K_PHY_NF); 1115 return sign_extend(AR5K_REG_MS(val, AR5K_PHY_NF_MINCCA_PWR), 9); 1116} 1117 1118void ath5k_hw_init_nfcal_hist(struct ath5k_hw *ah) 1119{ 1120 int i; 1121 1122 ah->ah_nfcal_hist.index = 0; 1123 for (i = 0; i < ATH5K_NF_CAL_HIST_MAX; i++) 1124 ah->ah_nfcal_hist.nfval[i] = AR5K_TUNE_CCA_MAX_GOOD_VALUE; 1125} 1126 1127static void ath5k_hw_update_nfcal_hist(struct ath5k_hw *ah, s16 noise_floor) 1128{ 1129 struct ath5k_nfcal_hist *hist = &ah->ah_nfcal_hist; 1130 hist->index = (hist->index + 1) & (ATH5K_NF_CAL_HIST_MAX-1); 1131 hist->nfval[hist->index] = noise_floor; 1132} 1133 1134static s16 ath5k_hw_get_median_noise_floor(struct ath5k_hw *ah) 1135{ 1136 s16 sort[ATH5K_NF_CAL_HIST_MAX]; 1137 s16 tmp; 1138 int i, j; 1139 1140 memcpy(sort, ah->ah_nfcal_hist.nfval, sizeof(sort)); 1141 for (i = 0; i < ATH5K_NF_CAL_HIST_MAX - 1; i++) { 1142 for (j = 1; j < ATH5K_NF_CAL_HIST_MAX - i; j++) { 1143 if (sort[j] > sort[j-1]) { 1144 tmp = sort[j]; 1145 sort[j] = sort[j-1]; 1146 sort[j-1] = tmp; 1147 } 1148 } 1149 } 1150 for (i = 0; i < ATH5K_NF_CAL_HIST_MAX; i++) { 1151 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1152 "cal %d:%d\n", i, sort[i]); 1153 } 1154 return sort[(ATH5K_NF_CAL_HIST_MAX-1) / 2]; 1155} 1156 1157/* 1158 * When we tell the hardware to perform a noise floor calibration 1159 * by setting the AR5K_PHY_AGCCTL_NF bit, it will periodically 1160 * sample-and-hold the minimum noise level seen at the antennas. 1161 * This value is then stored in a ring buffer of recently measured 1162 * noise floor values so we have a moving window of the last few 1163 * samples. 1164 * 1165 * The median of the values in the history is then loaded into the 1166 * hardware for its own use for RSSI and CCA measurements. 1167 */ 1168void ath5k_hw_update_noise_floor(struct ath5k_hw *ah) 1169{ 1170 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 1171 u32 val; 1172 s16 nf, threshold; 1173 u8 ee_mode; 1174 1175 /* keep last value if calibration hasn't completed */ 1176 if (ath5k_hw_reg_read(ah, AR5K_PHY_AGCCTL) & AR5K_PHY_AGCCTL_NF) { 1177 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1178 "NF did not complete in calibration window\n"); 1179 1180 return; 1181 } 1182 1183 switch (ah->ah_current_channel->hw_value & CHANNEL_MODES) { 1184 case CHANNEL_A: 1185 case CHANNEL_T: 1186 case CHANNEL_XR: 1187 ee_mode = AR5K_EEPROM_MODE_11A; 1188 break; 1189 case CHANNEL_G: 1190 case CHANNEL_TG: 1191 ee_mode = AR5K_EEPROM_MODE_11G; 1192 break; 1193 default: 1194 case CHANNEL_B: 1195 ee_mode = AR5K_EEPROM_MODE_11B; 1196 break; 1197 } 1198 1199 1200 /* completed NF calibration, test threshold */ 1201 nf = ath5k_hw_read_measured_noise_floor(ah); 1202 threshold = ee->ee_noise_floor_thr[ee_mode]; 1203 1204 if (nf > threshold) { 1205 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1206 "noise floor failure detected; " 1207 "read %d, threshold %d\n", 1208 nf, threshold); 1209 1210 nf = AR5K_TUNE_CCA_MAX_GOOD_VALUE; 1211 } 1212 1213 ath5k_hw_update_nfcal_hist(ah, nf); 1214 nf = ath5k_hw_get_median_noise_floor(ah); 1215 1216 /* load noise floor (in .5 dBm) so the hardware will use it */ 1217 val = ath5k_hw_reg_read(ah, AR5K_PHY_NF) & ~AR5K_PHY_NF_M; 1218 val |= (nf * 2) & AR5K_PHY_NF_M; 1219 ath5k_hw_reg_write(ah, val, AR5K_PHY_NF); 1220 1221 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_NF, 1222 ~(AR5K_PHY_AGCCTL_NF_EN | AR5K_PHY_AGCCTL_NF_NOUPDATE)); 1223 1224 ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_NF, 1225 0, false); 1226 1227 /* 1228 * Load a high max CCA Power value (-50 dBm in .5 dBm units) 1229 * so that we're not capped by the median we just loaded. 1230 * This will be used as the initial value for the next noise 1231 * floor calibration. 1232 */ 1233 val = (val & ~AR5K_PHY_NF_M) | ((-50 * 2) & AR5K_PHY_NF_M); 1234 ath5k_hw_reg_write(ah, val, AR5K_PHY_NF); 1235 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, 1236 AR5K_PHY_AGCCTL_NF_EN | 1237 AR5K_PHY_AGCCTL_NF_NOUPDATE | 1238 AR5K_PHY_AGCCTL_NF); 1239 1240 ah->ah_noise_floor = nf; 1241 1242 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1243 "noise floor calibrated: %d\n", nf); 1244} 1245 1246/* 1247 * Perform a PHY calibration on RF5110 1248 * -Fix BPSK/QAM Constellation (I/Q correction) 1249 */ 1250static int ath5k_hw_rf5110_calibrate(struct ath5k_hw *ah, 1251 struct ieee80211_channel *channel) 1252{ 1253 u32 phy_sig, phy_agc, phy_sat, beacon; 1254 int ret; 1255 1256 /* 1257 * Disable beacons and RX/TX queues, wait 1258 */ 1259 AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5210, 1260 AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210); 1261 beacon = ath5k_hw_reg_read(ah, AR5K_BEACON_5210); 1262 ath5k_hw_reg_write(ah, beacon & ~AR5K_BEACON_ENABLE, AR5K_BEACON_5210); 1263 1264 mdelay(2); 1265 1266 /* 1267 * Set the channel (with AGC turned off) 1268 */ 1269 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); 1270 udelay(10); 1271 ret = ath5k_hw_channel(ah, channel); 1272 1273 /* 1274 * Activate PHY and wait 1275 */ 1276 ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT); 1277 mdelay(1); 1278 1279 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); 1280 1281 if (ret) 1282 return ret; 1283 1284 /* 1285 * Calibrate the radio chip 1286 */ 1287 1288 /* Remember normal state */ 1289 phy_sig = ath5k_hw_reg_read(ah, AR5K_PHY_SIG); 1290 phy_agc = ath5k_hw_reg_read(ah, AR5K_PHY_AGCCOARSE); 1291 phy_sat = ath5k_hw_reg_read(ah, AR5K_PHY_ADCSAT); 1292 1293 /* Update radio registers */ 1294 ath5k_hw_reg_write(ah, (phy_sig & ~(AR5K_PHY_SIG_FIRPWR)) | 1295 AR5K_REG_SM(-1, AR5K_PHY_SIG_FIRPWR), AR5K_PHY_SIG); 1296 1297 ath5k_hw_reg_write(ah, (phy_agc & ~(AR5K_PHY_AGCCOARSE_HI | 1298 AR5K_PHY_AGCCOARSE_LO)) | 1299 AR5K_REG_SM(-1, AR5K_PHY_AGCCOARSE_HI) | 1300 AR5K_REG_SM(-127, AR5K_PHY_AGCCOARSE_LO), AR5K_PHY_AGCCOARSE); 1301 1302 ath5k_hw_reg_write(ah, (phy_sat & ~(AR5K_PHY_ADCSAT_ICNT | 1303 AR5K_PHY_ADCSAT_THR)) | 1304 AR5K_REG_SM(2, AR5K_PHY_ADCSAT_ICNT) | 1305 AR5K_REG_SM(12, AR5K_PHY_ADCSAT_THR), AR5K_PHY_ADCSAT); 1306 1307 udelay(20); 1308 1309 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); 1310 udelay(10); 1311 ath5k_hw_reg_write(ah, AR5K_PHY_RFSTG_DISABLE, AR5K_PHY_RFSTG); 1312 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); 1313 1314 mdelay(1); 1315 1316 /* 1317 * Enable calibration and wait until completion 1318 */ 1319 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_CAL); 1320 1321 ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, 1322 AR5K_PHY_AGCCTL_CAL, 0, false); 1323 1324 /* Reset to normal state */ 1325 ath5k_hw_reg_write(ah, phy_sig, AR5K_PHY_SIG); 1326 ath5k_hw_reg_write(ah, phy_agc, AR5K_PHY_AGCCOARSE); 1327 ath5k_hw_reg_write(ah, phy_sat, AR5K_PHY_ADCSAT); 1328 1329 if (ret) { 1330 ATH5K_ERR(ah->ah_sc, "calibration timeout (%uMHz)\n", 1331 channel->center_freq); 1332 return ret; 1333 } 1334 1335 /* 1336 * Re-enable RX/TX and beacons 1337 */ 1338 AR5K_REG_DISABLE_BITS(ah, AR5K_DIAG_SW_5210, 1339 AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210); 1340 ath5k_hw_reg_write(ah, beacon, AR5K_BEACON_5210); 1341 1342 return 0; 1343} 1344 1345/* 1346 * Perform I/Q calibration on RF5111/5112 and newer chips 1347 */ 1348static int 1349ath5k_hw_rf511x_iq_calibrate(struct ath5k_hw *ah) 1350{ 1351 u32 i_pwr, q_pwr; 1352 s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd; 1353 int i; 1354 1355 if (!ah->ah_calibration || 1356 ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) 1357 return 0; 1358 1359 /* Calibration has finished, get the results and re-run */ 1360 /* work around empty results which can apparently happen on 5212 */ 1361 for (i = 0; i <= 10; i++) { 1362 iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR); 1363 i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I); 1364 q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q); 1365 ATH5K_DBG_UNLIMIT(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1366 "iq_corr:%x i_pwr:%x q_pwr:%x", iq_corr, i_pwr, q_pwr); 1367 if (i_pwr && q_pwr) 1368 break; 1369 } 1370 1371 i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7; 1372 1373 if (ah->ah_version == AR5K_AR5211) 1374 q_coffd = q_pwr >> 6; 1375 else 1376 q_coffd = q_pwr >> 7; 1377 1378 /* protect against divide by 0 and loss of sign bits */ 1379 if (i_coffd == 0 || q_coffd < 2) 1380 return -1; 1381 1382 i_coff = (-iq_corr) / i_coffd; 1383 i_coff = clamp(i_coff, -32, 31); /* signed 6 bit */ 1384 1385 if (ah->ah_version == AR5K_AR5211) 1386 q_coff = (i_pwr / q_coffd) - 64; 1387 else 1388 q_coff = (i_pwr / q_coffd) - 128; 1389 q_coff = clamp(q_coff, -16, 15); /* signed 5 bit */ 1390 1391 ATH5K_DBG_UNLIMIT(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, 1392 "new I:%d Q:%d (i_coffd:%x q_coffd:%x)", 1393 i_coff, q_coff, i_coffd, q_coffd); 1394 1395 /* Commit new I/Q values (set enable bit last to match HAL sources) */ 1396 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_Q_I_COFF, i_coff); 1397 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_Q_Q_COFF, q_coff); 1398 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE); 1399 1400 /* Re-enable calibration -if we don't we'll commit 1401 * the same values again and again */ 1402 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, 1403 AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); 1404 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_RUN); 1405 1406 return 0; 1407} 1408 1409/* 1410 * Perform a PHY calibration 1411 */ 1412int ath5k_hw_phy_calibrate(struct ath5k_hw *ah, 1413 struct ieee80211_channel *channel) 1414{ 1415 int ret; 1416 1417 if (ah->ah_radio == AR5K_RF5110) 1418 ret = ath5k_hw_rf5110_calibrate(ah, channel); 1419 else { 1420 ret = ath5k_hw_rf511x_iq_calibrate(ah); 1421 ath5k_hw_request_rfgain_probe(ah); 1422 } 1423 1424 return ret; 1425} 1426 1427/***************************\ 1428* Spur mitigation functions * 1429\***************************/ 1430 1431bool ath5k_hw_chan_has_spur_noise(struct ath5k_hw *ah, 1432 struct ieee80211_channel *channel) 1433{ 1434 u8 refclk_freq; 1435 1436 if ((ah->ah_radio == AR5K_RF5112) || 1437 (ah->ah_radio == AR5K_RF5413) || 1438 (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) 1439 refclk_freq = 40; 1440 else 1441 refclk_freq = 32; 1442 1443 if ((channel->center_freq % refclk_freq != 0) && 1444 ((channel->center_freq % refclk_freq < 10) || 1445 (channel->center_freq % refclk_freq > 22))) 1446 return true; 1447 else 1448 return false; 1449} 1450 1451void 1452ath5k_hw_set_spur_mitigation_filter(struct ath5k_hw *ah, 1453 struct ieee80211_channel *channel) 1454{ 1455 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 1456 u32 mag_mask[4] = {0, 0, 0, 0}; 1457 u32 pilot_mask[2] = {0, 0}; 1458 /* Note: fbin values are scaled up by 2 */ 1459 u16 spur_chan_fbin, chan_fbin, symbol_width, spur_detection_window; 1460 s32 spur_delta_phase, spur_freq_sigma_delta; 1461 s32 spur_offset, num_symbols_x16; 1462 u8 num_symbol_offsets, i, freq_band; 1463 1464 /* Convert current frequency to fbin value (the same way channels 1465 * are stored on EEPROM, check out ath5k_eeprom_bin2freq) and scale 1466 * up by 2 so we can compare it later */ 1467 if (channel->hw_value & CHANNEL_2GHZ) { 1468 chan_fbin = (channel->center_freq - 2300) * 10; 1469 freq_band = AR5K_EEPROM_BAND_2GHZ; 1470 } else { 1471 chan_fbin = (channel->center_freq - 4900) * 10; 1472 freq_band = AR5K_EEPROM_BAND_5GHZ; 1473 } 1474 1475 /* Check if any spur_chan_fbin from EEPROM is 1476 * within our current channel's spur detection range */ 1477 spur_chan_fbin = AR5K_EEPROM_NO_SPUR; 1478 spur_detection_window = AR5K_SPUR_CHAN_WIDTH; 1479 /* XXX: Half/Quarter channels ?*/ 1480 if (channel->hw_value & CHANNEL_TURBO) 1481 spur_detection_window *= 2; 1482 1483 for (i = 0; i < AR5K_EEPROM_N_SPUR_CHANS; i++) { 1484 spur_chan_fbin = ee->ee_spur_chans[i][freq_band]; 1485 1486 /* Note: mask cleans AR5K_EEPROM_NO_SPUR flag 1487 * so it's zero if we got nothing from EEPROM */ 1488 if (spur_chan_fbin == AR5K_EEPROM_NO_SPUR) { 1489 spur_chan_fbin &= AR5K_EEPROM_SPUR_CHAN_MASK; 1490 break; 1491 } 1492 1493 if ((chan_fbin - spur_detection_window <= 1494 (spur_chan_fbin & AR5K_EEPROM_SPUR_CHAN_MASK)) && 1495 (chan_fbin + spur_detection_window >= 1496 (spur_chan_fbin & AR5K_EEPROM_SPUR_CHAN_MASK))) { 1497 spur_chan_fbin &= AR5K_EEPROM_SPUR_CHAN_MASK; 1498 break; 1499 } 1500 } 1501 1502 /* We need to enable spur filter for this channel */ 1503 if (spur_chan_fbin) { 1504 spur_offset = spur_chan_fbin - chan_fbin; 1505 /* 1506 * Calculate deltas: 1507 * spur_freq_sigma_delta -> spur_offset / sample_freq << 21 1508 * spur_delta_phase -> spur_offset / chip_freq << 11 1509 * Note: Both values have 100KHz resolution 1510 */ 1511 /* XXX: Half/Quarter rate channels ? */ 1512 switch (channel->hw_value) { 1513 case CHANNEL_A: 1514 /* Both sample_freq and chip_freq are 40MHz */ 1515 spur_delta_phase = (spur_offset << 17) / 25; 1516 spur_freq_sigma_delta = (spur_delta_phase >> 10); 1517 symbol_width = AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz; 1518 break; 1519 case CHANNEL_G: 1520 /* sample_freq -> 40MHz chip_freq -> 44MHz 1521 * (for b compatibility) */ 1522 spur_freq_sigma_delta = (spur_offset << 8) / 55; 1523 spur_delta_phase = (spur_offset << 17) / 25; 1524 symbol_width = AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz; 1525 break; 1526 case CHANNEL_T: 1527 case CHANNEL_TG: 1528 /* Both sample_freq and chip_freq are 80MHz */ 1529 spur_delta_phase = (spur_offset << 16) / 25; 1530 spur_freq_sigma_delta = (spur_delta_phase >> 10); 1531 symbol_width = AR5K_SPUR_SYMBOL_WIDTH_TURBO_100Hz; 1532 break; 1533 default: 1534 return; 1535 } 1536 1537 /* Calculate pilot and magnitude masks */ 1538 1539 /* Scale up spur_offset by 1000 to switch to 100HZ resolution 1540 * and divide by symbol_width to find how many symbols we have 1541 * Note: number of symbols is scaled up by 16 */ 1542 num_symbols_x16 = ((spur_offset * 1000) << 4) / symbol_width; 1543 1544 /* Spur is on a symbol if num_symbols_x16 % 16 is zero */ 1545 if (!(num_symbols_x16 & 0xF)) 1546 /* _X_ */ 1547 num_symbol_offsets = 3; 1548 else 1549 /* _xx_ */ 1550 num_symbol_offsets = 4; 1551 1552 for (i = 0; i < num_symbol_offsets; i++) { 1553 1554 /* Calculate pilot mask */ 1555 s32 curr_sym_off = 1556 (num_symbols_x16 / 16) + i + 25; 1557 1558 /* Pilot magnitude mask seems to be a way to 1559 * declare the boundaries for our detection 1560 * window or something, it's 2 for the middle 1561 * value(s) where the symbol is expected to be 1562 * and 1 on the boundary values */ 1563 u8 plt_mag_map = 1564 (i == 0 || i == (num_symbol_offsets - 1)) 1565 ? 1 : 2; 1566 1567 if (curr_sym_off >= 0 && curr_sym_off <= 32) { 1568 if (curr_sym_off <= 25) 1569 pilot_mask[0] |= 1 << curr_sym_off; 1570 else if (curr_sym_off >= 27) 1571 pilot_mask[0] |= 1 << (curr_sym_off - 1); 1572 } else if (curr_sym_off >= 33 && curr_sym_off <= 52) 1573 pilot_mask[1] |= 1 << (curr_sym_off - 33); 1574 1575 /* Calculate magnitude mask (for viterbi decoder) */ 1576 if (curr_sym_off >= -1 && curr_sym_off <= 14) 1577 mag_mask[0] |= 1578 plt_mag_map << (curr_sym_off + 1) * 2; 1579 else if (curr_sym_off >= 15 && curr_sym_off <= 30) 1580 mag_mask[1] |= 1581 plt_mag_map << (curr_sym_off - 15) * 2; 1582 else if (curr_sym_off >= 31 && curr_sym_off <= 46) 1583 mag_mask[2] |= 1584 plt_mag_map << (curr_sym_off - 31) * 2; 1585 else if (curr_sym_off >= 46 && curr_sym_off <= 53) 1586 mag_mask[3] |= 1587 plt_mag_map << (curr_sym_off - 47) * 2; 1588 1589 } 1590 1591 /* Write settings on hw to enable spur filter */ 1592 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, 1593 AR5K_PHY_BIN_MASK_CTL_RATE, 0xff); 1594 /* XXX: Self correlator also ? */ 1595 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, 1596 AR5K_PHY_IQ_PILOT_MASK_EN | 1597 AR5K_PHY_IQ_CHAN_MASK_EN | 1598 AR5K_PHY_IQ_SPUR_FILT_EN); 1599 1600 /* Set delta phase and freq sigma delta */ 1601 ath5k_hw_reg_write(ah, 1602 AR5K_REG_SM(spur_delta_phase, 1603 AR5K_PHY_TIMING_11_SPUR_DELTA_PHASE) | 1604 AR5K_REG_SM(spur_freq_sigma_delta, 1605 AR5K_PHY_TIMING_11_SPUR_FREQ_SD) | 1606 AR5K_PHY_TIMING_11_USE_SPUR_IN_AGC, 1607 AR5K_PHY_TIMING_11); 1608 1609 /* Write pilot masks */ 1610 ath5k_hw_reg_write(ah, pilot_mask[0], AR5K_PHY_TIMING_7); 1611 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_8, 1612 AR5K_PHY_TIMING_8_PILOT_MASK_2, 1613 pilot_mask[1]); 1614 1615 ath5k_hw_reg_write(ah, pilot_mask[0], AR5K_PHY_TIMING_9); 1616 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_10, 1617 AR5K_PHY_TIMING_10_PILOT_MASK_2, 1618 pilot_mask[1]); 1619 1620 /* Write magnitude masks */ 1621 ath5k_hw_reg_write(ah, mag_mask[0], AR5K_PHY_BIN_MASK_1); 1622 ath5k_hw_reg_write(ah, mag_mask[1], AR5K_PHY_BIN_MASK_2); 1623 ath5k_hw_reg_write(ah, mag_mask[2], AR5K_PHY_BIN_MASK_3); 1624 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, 1625 AR5K_PHY_BIN_MASK_CTL_MASK_4, 1626 mag_mask[3]); 1627 1628 ath5k_hw_reg_write(ah, mag_mask[0], AR5K_PHY_BIN_MASK2_1); 1629 ath5k_hw_reg_write(ah, mag_mask[1], AR5K_PHY_BIN_MASK2_2); 1630 ath5k_hw_reg_write(ah, mag_mask[2], AR5K_PHY_BIN_MASK2_3); 1631 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK2_4, 1632 AR5K_PHY_BIN_MASK2_4_MASK_4, 1633 mag_mask[3]); 1634 1635 } else if (ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & 1636 AR5K_PHY_IQ_SPUR_FILT_EN) { 1637 /* Clean up spur mitigation settings and disable fliter */ 1638 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, 1639 AR5K_PHY_BIN_MASK_CTL_RATE, 0); 1640 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_IQ, 1641 AR5K_PHY_IQ_PILOT_MASK_EN | 1642 AR5K_PHY_IQ_CHAN_MASK_EN | 1643 AR5K_PHY_IQ_SPUR_FILT_EN); 1644 ath5k_hw_reg_write(ah, 0, AR5K_PHY_TIMING_11); 1645 1646 /* Clear pilot masks */ 1647 ath5k_hw_reg_write(ah, 0, AR5K_PHY_TIMING_7); 1648 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_8, 1649 AR5K_PHY_TIMING_8_PILOT_MASK_2, 1650 0); 1651 1652 ath5k_hw_reg_write(ah, 0, AR5K_PHY_TIMING_9); 1653 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_10, 1654 AR5K_PHY_TIMING_10_PILOT_MASK_2, 1655 0); 1656 1657 /* Clear magnitude masks */ 1658 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK_1); 1659 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK_2); 1660 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK_3); 1661 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, 1662 AR5K_PHY_BIN_MASK_CTL_MASK_4, 1663 0); 1664 1665 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK2_1); 1666 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK2_2); 1667 ath5k_hw_reg_write(ah, 0, AR5K_PHY_BIN_MASK2_3); 1668 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK2_4, 1669 AR5K_PHY_BIN_MASK2_4_MASK_4, 1670 0); 1671 } 1672} 1673 1674/********************\ 1675 Misc PHY functions 1676\********************/ 1677 1678int ath5k_hw_phy_disable(struct ath5k_hw *ah) 1679{ 1680 /*Just a try M.F.*/ 1681 ath5k_hw_reg_write(ah, AR5K_PHY_ACT_DISABLE, AR5K_PHY_ACT); 1682 1683 return 0; 1684} 1685 1686/* 1687 * Get the PHY Chip revision 1688 */ 1689u16 ath5k_hw_radio_revision(struct ath5k_hw *ah, unsigned int chan) 1690{ 1691 unsigned int i; 1692 u32 srev; 1693 u16 ret; 1694 1695 /* 1696 * Set the radio chip access register 1697 */ 1698 switch (chan) { 1699 case CHANNEL_2GHZ: 1700 ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_2GHZ, AR5K_PHY(0)); 1701 break; 1702 case CHANNEL_5GHZ: 1703 ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); 1704 break; 1705 default: 1706 return 0; 1707 } 1708 1709 mdelay(2); 1710 1711 /* ...wait until PHY is ready and read the selected radio revision */ 1712 ath5k_hw_reg_write(ah, 0x00001c16, AR5K_PHY(0x34)); 1713 1714 for (i = 0; i < 8; i++) 1715 ath5k_hw_reg_write(ah, 0x00010000, AR5K_PHY(0x20)); 1716 1717 if (ah->ah_version == AR5K_AR5210) { 1718 srev = ath5k_hw_reg_read(ah, AR5K_PHY(256) >> 28) & 0xf; 1719 ret = (u16)ath5k_hw_bitswap(srev, 4) + 1; 1720 } else { 1721 srev = (ath5k_hw_reg_read(ah, AR5K_PHY(0x100)) >> 24) & 0xff; 1722 ret = (u16)ath5k_hw_bitswap(((srev & 0xf0) >> 4) | 1723 ((srev & 0x0f) << 4), 8); 1724 } 1725 1726 /* Reset to the 5GHz mode */ 1727 ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); 1728 1729 return ret; 1730} 1731 1732/*****************\ 1733* Antenna control * 1734\*****************/ 1735 1736static void /*TODO:Boundary check*/ 1737ath5k_hw_set_def_antenna(struct ath5k_hw *ah, u8 ant) 1738{ 1739 if (ah->ah_version != AR5K_AR5210) 1740 ath5k_hw_reg_write(ah, ant & 0x7, AR5K_DEFAULT_ANTENNA); 1741} 1742 1743/* 1744 * Enable/disable fast rx antenna diversity 1745 */ 1746static void 1747ath5k_hw_set_fast_div(struct ath5k_hw *ah, u8 ee_mode, bool enable) 1748{ 1749 switch (ee_mode) { 1750 case AR5K_EEPROM_MODE_11G: 1751 /* XXX: This is set to 1752 * disabled on initvals !!! */ 1753 case AR5K_EEPROM_MODE_11A: 1754 if (enable) 1755 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGCCTL, 1756 AR5K_PHY_AGCCTL_OFDM_DIV_DIS); 1757 else 1758 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, 1759 AR5K_PHY_AGCCTL_OFDM_DIV_DIS); 1760 break; 1761 case AR5K_EEPROM_MODE_11B: 1762 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, 1763 AR5K_PHY_AGCCTL_OFDM_DIV_DIS); 1764 break; 1765 default: 1766 return; 1767 } 1768 1769 if (enable) { 1770 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_RESTART, 1771 AR5K_PHY_RESTART_DIV_GC, 0xc); 1772 1773 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_FAST_ANT_DIV, 1774 AR5K_PHY_FAST_ANT_DIV_EN); 1775 } else { 1776 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_RESTART, 1777 AR5K_PHY_RESTART_DIV_GC, 0x8); 1778 1779 AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_FAST_ANT_DIV, 1780 AR5K_PHY_FAST_ANT_DIV_EN); 1781 } 1782} 1783 1784/* 1785 * Set antenna operating mode 1786 */ 1787void 1788ath5k_hw_set_antenna_mode(struct ath5k_hw *ah, u8 ant_mode) 1789{ 1790 struct ieee80211_channel *channel = ah->ah_current_channel; 1791 bool use_def_for_tx, update_def_on_tx, use_def_for_rts, fast_div; 1792 bool use_def_for_sg; 1793 u8 def_ant, tx_ant, ee_mode; 1794 u32 sta_id1 = 0; 1795 1796 def_ant = ah->ah_def_ant; 1797 1798 switch (channel->hw_value & CHANNEL_MODES) { 1799 case CHANNEL_A: 1800 case CHANNEL_T: 1801 case CHANNEL_XR: 1802 ee_mode = AR5K_EEPROM_MODE_11A; 1803 break; 1804 case CHANNEL_G: 1805 case CHANNEL_TG: 1806 ee_mode = AR5K_EEPROM_MODE_11G; 1807 break; 1808 case CHANNEL_B: 1809 ee_mode = AR5K_EEPROM_MODE_11B; 1810 break; 1811 default: 1812 ATH5K_ERR(ah->ah_sc, 1813 "invalid channel: %d\n", channel->center_freq); 1814 return; 1815 } 1816 1817 switch (ant_mode) { 1818 case AR5K_ANTMODE_DEFAULT: 1819 tx_ant = 0; 1820 use_def_for_tx = false; 1821 update_def_on_tx = false; 1822 use_def_for_rts = false; 1823 use_def_for_sg = false; 1824 fast_div = true; 1825 break; 1826 case AR5K_ANTMODE_FIXED_A: 1827 def_ant = 1; 1828 tx_ant = 1; 1829 use_def_for_tx = true; 1830 update_def_on_tx = false; 1831 use_def_for_rts = true; 1832 use_def_for_sg = true; 1833 fast_div = false; 1834 break; 1835 case AR5K_ANTMODE_FIXED_B: 1836 def_ant = 2; 1837 tx_ant = 2; 1838 use_def_for_tx = true; 1839 update_def_on_tx = false; 1840 use_def_for_rts = true; 1841 use_def_for_sg = true; 1842 fast_div = false; 1843 break; 1844 case AR5K_ANTMODE_SINGLE_AP: 1845 def_ant = 1; /* updated on tx */ 1846 tx_ant = 0; 1847 use_def_for_tx = true; 1848 update_def_on_tx = true; 1849 use_def_for_rts = true; 1850 use_def_for_sg = true; 1851 fast_div = true; 1852 break; 1853 case AR5K_ANTMODE_SECTOR_AP: 1854 tx_ant = 1; /* variable */ 1855 use_def_for_tx = false; 1856 update_def_on_tx = false; 1857 use_def_for_rts = true; 1858 use_def_for_sg = false; 1859 fast_div = false; 1860 break; 1861 case AR5K_ANTMODE_SECTOR_STA: 1862 tx_ant = 1; /* variable */ 1863 use_def_for_tx = true; 1864 update_def_on_tx = false; 1865 use_def_for_rts = true; 1866 use_def_for_sg = false; 1867 fast_div = true; 1868 break; 1869 case AR5K_ANTMODE_DEBUG: 1870 def_ant = 1; 1871 tx_ant = 2; 1872 use_def_for_tx = false; 1873 update_def_on_tx = false; 1874 use_def_for_rts = false; 1875 use_def_for_sg = false; 1876 fast_div = false; 1877 break; 1878 default: 1879 return; 1880 } 1881 1882 ah->ah_tx_ant = tx_ant; 1883 ah->ah_ant_mode = ant_mode; 1884 ah->ah_def_ant = def_ant; 1885 1886 sta_id1 |= use_def_for_tx ? AR5K_STA_ID1_DEFAULT_ANTENNA : 0; 1887 sta_id1 |= update_def_on_tx ? AR5K_STA_ID1_DESC_ANTENNA : 0; 1888 sta_id1 |= use_def_for_rts ? AR5K_STA_ID1_RTS_DEF_ANTENNA : 0; 1889 sta_id1 |= use_def_for_sg ? AR5K_STA_ID1_SELFGEN_DEF_ANT : 0; 1890 1891 AR5K_REG_DISABLE_BITS(ah, AR5K_STA_ID1, AR5K_STA_ID1_ANTENNA_SETTINGS); 1892 1893 if (sta_id1) 1894 AR5K_REG_ENABLE_BITS(ah, AR5K_STA_ID1, sta_id1); 1895 1896 /* Note: set diversity before default antenna 1897 * because it won't work correctly */ 1898 ath5k_hw_set_fast_div(ah, ee_mode, fast_div); 1899 ath5k_hw_set_def_antenna(ah, def_ant); 1900} 1901 1902 1903/****************\ 1904* TX power setup * 1905\****************/ 1906 1907/* 1908 * Helper functions 1909 */ 1910 1911/* 1912 * Do linear interpolation between two given (x, y) points 1913 */ 1914static s16 1915ath5k_get_interpolated_value(s16 target, s16 x_left, s16 x_right, 1916 s16 y_left, s16 y_right) 1917{ 1918 s16 ratio, result; 1919 1920 /* Avoid divide by zero and skip interpolation 1921 * if we have the same point */ 1922 if ((x_left == x_right) || (y_left == y_right)) 1923 return y_left; 1924 1925 /* 1926 * Since we use ints and not fps, we need to scale up in 1927 * order to get a sane ratio value (or else we 'll eg. get 1928 * always 1 instead of 1.25, 1.75 etc). We scale up by 100 1929 * to have some accuracy both for 0.5 and 0.25 steps. 1930 */ 1931 ratio = ((100 * y_right - 100 * y_left)/(x_right - x_left)); 1932 1933 /* Now scale down to be in range */ 1934 result = y_left + (ratio * (target - x_left) / 100); 1935 1936 return result; 1937} 1938 1939/* 1940 * Find vertical boundary (min pwr) for the linear PCDAC curve. 1941 * 1942 * Since we have the top of the curve and we draw the line below 1943 * until we reach 1 (1 pcdac step) we need to know which point 1944 * (x value) that is so that we don't go below y axis and have negative 1945 * pcdac values when creating the curve, or fill the table with zeroes. 1946 */ 1947static s16 1948ath5k_get_linear_pcdac_min(const u8 *stepL, const u8 *stepR, 1949 const s16 *pwrL, const s16 *pwrR) 1950{ 1951 s8 tmp; 1952 s16 min_pwrL, min_pwrR; 1953 s16 pwr_i; 1954 1955 /* Some vendors write the same pcdac value twice !!! */ 1956 if (stepL[0] == stepL[1] || stepR[0] == stepR[1]) 1957 return max(pwrL[0], pwrR[0]); 1958 1959 if (pwrL[0] == pwrL[1]) 1960 min_pwrL = pwrL[0]; 1961 else { 1962 pwr_i = pwrL[0]; 1963 do { 1964 pwr_i--; 1965 tmp = (s8) ath5k_get_interpolated_value(pwr_i, 1966 pwrL[0], pwrL[1], 1967 stepL[0], stepL[1]); 1968 } while (tmp > 1); 1969 1970 min_pwrL = pwr_i; 1971 } 1972 1973 if (pwrR[0] == pwrR[1]) 1974 min_pwrR = pwrR[0]; 1975 else { 1976 pwr_i = pwrR[0]; 1977 do { 1978 pwr_i--; 1979 tmp = (s8) ath5k_get_interpolated_value(pwr_i, 1980 pwrR[0], pwrR[1], 1981 stepR[0], stepR[1]); 1982 } while (tmp > 1); 1983 1984 min_pwrR = pwr_i; 1985 } 1986 1987 /* Keep the right boundary so that it works for both curves */ 1988 return max(min_pwrL, min_pwrR); 1989} 1990 1991/* 1992 * Interpolate (pwr,vpd) points to create a Power to PDADC or a 1993 * Power to PCDAC curve. 1994 * 1995 * Each curve has power on x axis (in 0.5dB units) and PCDAC/PDADC 1996 * steps (offsets) on y axis. Power can go up to 31.5dB and max 1997 * PCDAC/PDADC step for each curve is 64 but we can write more than 1998 * one curves on hw so we can go up to 128 (which is the max step we 1999 * can write on the final table). 2000 * 2001 * We write y values (PCDAC/PDADC steps) on hw. 2002 */ 2003static void 2004ath5k_create_power_curve(s16 pmin, s16 pmax, 2005 const s16 *pwr, const u8 *vpd, 2006 u8 num_points, 2007 u8 *vpd_table, u8 type) 2008{ 2009 u8 idx[2] = { 0, 1 }; 2010 s16 pwr_i = 2*pmin; 2011 int i; 2012 2013 if (num_points < 2) 2014 return; 2015 2016 /* We want the whole line, so adjust boundaries 2017 * to cover the entire power range. Note that 2018 * power values are already 0.25dB so no need 2019 * to multiply pwr_i by 2 */ 2020 if (type == AR5K_PWRTABLE_LINEAR_PCDAC) { 2021 pwr_i = pmin; 2022 pmin = 0; 2023 pmax = 63; 2024 } 2025 2026 /* Find surrounding turning points (TPs) 2027 * and interpolate between them */ 2028 for (i = 0; (i <= (u16) (pmax - pmin)) && 2029 (i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) { 2030 2031 /* We passed the right TP, move to the next set of TPs 2032 * if we pass the last TP, extrapolate above using the last 2033 * two TPs for ratio */ 2034 if ((pwr_i > pwr[idx[1]]) && (idx[1] < num_points - 1)) { 2035 idx[0]++; 2036 idx[1]++; 2037 } 2038 2039 vpd_table[i] = (u8) ath5k_get_interpolated_value(pwr_i, 2040 pwr[idx[0]], pwr[idx[1]], 2041 vpd[idx[0]], vpd[idx[1]]); 2042 2043 /* Increase by 0.5dB 2044 * (0.25 dB units) */ 2045 pwr_i += 2; 2046 } 2047} 2048 2049/* 2050 * Get the surrounding per-channel power calibration piers 2051 * for a given frequency so that we can interpolate between 2052 * them and come up with an apropriate dataset for our current 2053 * channel. 2054 */ 2055static void 2056ath5k_get_chan_pcal_surrounding_piers(struct ath5k_hw *ah, 2057 struct ieee80211_channel *channel, 2058 struct ath5k_chan_pcal_info **pcinfo_l, 2059 struct ath5k_chan_pcal_info **pcinfo_r) 2060{ 2061 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 2062 struct ath5k_chan_pcal_info *pcinfo; 2063 u8 idx_l, idx_r; 2064 u8 mode, max, i; 2065 u32 target = channel->center_freq; 2066 2067 idx_l = 0; 2068 idx_r = 0; 2069 2070 if (!(channel->hw_value & CHANNEL_OFDM)) { 2071 pcinfo = ee->ee_pwr_cal_b; 2072 mode = AR5K_EEPROM_MODE_11B; 2073 } else if (channel->hw_value & CHANNEL_2GHZ) { 2074 pcinfo = ee->ee_pwr_cal_g; 2075 mode = AR5K_EEPROM_MODE_11G; 2076 } else { 2077 pcinfo = ee->ee_pwr_cal_a; 2078 mode = AR5K_EEPROM_MODE_11A; 2079 } 2080 max = ee->ee_n_piers[mode] - 1; 2081 2082 /* Frequency is below our calibrated 2083 * range. Use the lowest power curve 2084 * we have */ 2085 if (target < pcinfo[0].freq) { 2086 idx_l = idx_r = 0; 2087 goto done; 2088 } 2089 2090 /* Frequency is above our calibrated 2091 * range. Use the highest power curve 2092 * we have */ 2093 if (target > pcinfo[max].freq) { 2094 idx_l = idx_r = max; 2095 goto done; 2096 } 2097 2098 /* Frequency is inside our calibrated 2099 * channel range. Pick the surrounding 2100 * calibration piers so that we can 2101 * interpolate */ 2102 for (i = 0; i <= max; i++) { 2103 2104 /* Frequency matches one of our calibration 2105 * piers, no need to interpolate, just use 2106 * that calibration pier */ 2107 if (pcinfo[i].freq == target) { 2108 idx_l = idx_r = i; 2109 goto done; 2110 } 2111 2112 /* We found a calibration pier that's above 2113 * frequency, use this pier and the previous 2114 * one to interpolate */ 2115 if (target < pcinfo[i].freq) { 2116 idx_r = i; 2117 idx_l = idx_r - 1; 2118 goto done; 2119 } 2120 } 2121 2122done: 2123 *pcinfo_l = &pcinfo[idx_l]; 2124 *pcinfo_r = &pcinfo[idx_r]; 2125} 2126 2127/* 2128 * Get the surrounding per-rate power calibration data 2129 * for a given frequency and interpolate between power 2130 * values to set max target power supported by hw for 2131 * each rate. 2132 */ 2133static void 2134ath5k_get_rate_pcal_data(struct ath5k_hw *ah, 2135 struct ieee80211_channel *channel, 2136 struct ath5k_rate_pcal_info *rates) 2137{ 2138 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 2139 struct ath5k_rate_pcal_info *rpinfo; 2140 u8 idx_l, idx_r; 2141 u8 mode, max, i; 2142 u32 target = channel->center_freq; 2143 2144 idx_l = 0; 2145 idx_r = 0; 2146 2147 if (!(channel->hw_value & CHANNEL_OFDM)) { 2148 rpinfo = ee->ee_rate_tpwr_b; 2149 mode = AR5K_EEPROM_MODE_11B; 2150 } else if (channel->hw_value & CHANNEL_2GHZ) { 2151 rpinfo = ee->ee_rate_tpwr_g; 2152 mode = AR5K_EEPROM_MODE_11G; 2153 } else { 2154 rpinfo = ee->ee_rate_tpwr_a; 2155 mode = AR5K_EEPROM_MODE_11A; 2156 } 2157 max = ee->ee_rate_target_pwr_num[mode] - 1; 2158 2159 /* Get the surrounding calibration 2160 * piers - same as above */ 2161 if (target < rpinfo[0].freq) { 2162 idx_l = idx_r = 0; 2163 goto done; 2164 } 2165 2166 if (target > rpinfo[max].freq) { 2167 idx_l = idx_r = max; 2168 goto done; 2169 } 2170 2171 for (i = 0; i <= max; i++) { 2172 2173 if (rpinfo[i].freq == target) { 2174 idx_l = idx_r = i; 2175 goto done; 2176 } 2177 2178 if (target < rpinfo[i].freq) { 2179 idx_r = i; 2180 idx_l = idx_r - 1; 2181 goto done; 2182 } 2183 } 2184 2185done: 2186 /* Now interpolate power value, based on the frequency */ 2187 rates->freq = target; 2188 2189 rates->target_power_6to24 = 2190 ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, 2191 rpinfo[idx_r].freq, 2192 rpinfo[idx_l].target_power_6to24, 2193 rpinfo[idx_r].target_power_6to24); 2194 2195 rates->target_power_36 = 2196 ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, 2197 rpinfo[idx_r].freq, 2198 rpinfo[idx_l].target_power_36, 2199 rpinfo[idx_r].target_power_36); 2200 2201 rates->target_power_48 = 2202 ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, 2203 rpinfo[idx_r].freq, 2204 rpinfo[idx_l].target_power_48, 2205 rpinfo[idx_r].target_power_48); 2206 2207 rates->target_power_54 = 2208 ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, 2209 rpinfo[idx_r].freq, 2210 rpinfo[idx_l].target_power_54, 2211 rpinfo[idx_r].target_power_54); 2212} 2213 2214/* 2215 * Get the max edge power for this channel if 2216 * we have such data from EEPROM's Conformance Test 2217 * Limits (CTL), and limit max power if needed. 2218 */ 2219static void 2220ath5k_get_max_ctl_power(struct ath5k_hw *ah, 2221 struct ieee80211_channel *channel) 2222{ 2223 struct ath_regulatory *regulatory = ath5k_hw_regulatory(ah); 2224 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 2225 struct ath5k_edge_power *rep = ee->ee_ctl_pwr; 2226 u8 *ctl_val = ee->ee_ctl; 2227 s16 max_chan_pwr = ah->ah_txpower.txp_max_pwr / 4; 2228 s16 edge_pwr = 0; 2229 u8 rep_idx; 2230 u8 i, ctl_mode; 2231 u8 ctl_idx = 0xFF; 2232 u32 target = channel->center_freq; 2233 2234 ctl_mode = ath_regd_get_band_ctl(regulatory, channel->band); 2235 2236 switch (channel->hw_value & CHANNEL_MODES) { 2237 case CHANNEL_A: 2238 ctl_mode |= AR5K_CTL_11A; 2239 break; 2240 case CHANNEL_G: 2241 ctl_mode |= AR5K_CTL_11G; 2242 break; 2243 case CHANNEL_B: 2244 ctl_mode |= AR5K_CTL_11B; 2245 break; 2246 case CHANNEL_T: 2247 ctl_mode |= AR5K_CTL_TURBO; 2248 break; 2249 case CHANNEL_TG: 2250 ctl_mode |= AR5K_CTL_TURBOG; 2251 break; 2252 case CHANNEL_XR: 2253 /* Fall through */ 2254 default: 2255 return; 2256 } 2257 2258 for (i = 0; i < ee->ee_ctls; i++) { 2259 if (ctl_val[i] == ctl_mode) { 2260 ctl_idx = i; 2261 break; 2262 } 2263 } 2264 2265 /* If we have a CTL dataset available grab it and find the 2266 * edge power for our frequency */ 2267 if (ctl_idx == 0xFF) 2268 return; 2269 2270 /* Edge powers are sorted by frequency from lower 2271 * to higher. Each CTL corresponds to 8 edge power 2272 * measurements. */ 2273 rep_idx = ctl_idx * AR5K_EEPROM_N_EDGES; 2274 2275 /* Don't do boundaries check because we 2276 * might have more that one bands defined 2277 * for this mode */ 2278 2279 /* Get the edge power that's closer to our 2280 * frequency */ 2281 for (i = 0; i < AR5K_EEPROM_N_EDGES; i++) { 2282 rep_idx += i; 2283 if (target <= rep[rep_idx].freq) 2284 edge_pwr = (s16) rep[rep_idx].edge; 2285 } 2286 2287 if (edge_pwr) 2288 ah->ah_txpower.txp_max_pwr = 4*min(edge_pwr, max_chan_pwr); 2289} 2290 2291 2292/* 2293 * Power to PCDAC table functions 2294 */ 2295 2296/* 2297 * Fill Power to PCDAC table on RF5111 2298 * 2299 * No further processing is needed for RF5111, the only thing we have to 2300 * do is fill the values below and above calibration range since eeprom data 2301 * may not cover the entire PCDAC table. 2302 */ 2303static void 2304ath5k_fill_pwr_to_pcdac_table(struct ath5k_hw *ah, s16* table_min, 2305 s16 *table_max) 2306{ 2307 u8 *pcdac_out = ah->ah_txpower.txp_pd_table; 2308 u8 *pcdac_tmp = ah->ah_txpower.tmpL[0]; 2309 u8 pcdac_0, pcdac_n, pcdac_i, pwr_idx, i; 2310 s16 min_pwr, max_pwr; 2311 2312 /* Get table boundaries */ 2313 min_pwr = table_min[0]; 2314 pcdac_0 = pcdac_tmp[0]; 2315 2316 max_pwr = table_max[0]; 2317 pcdac_n = pcdac_tmp[table_max[0] - table_min[0]]; 2318 2319 /* Extrapolate below minimum using pcdac_0 */ 2320 pcdac_i = 0; 2321 for (i = 0; i < min_pwr; i++) 2322 pcdac_out[pcdac_i++] = pcdac_0; 2323 2324 /* Copy values from pcdac_tmp */ 2325 pwr_idx = min_pwr; 2326 for (i = 0 ; pwr_idx <= max_pwr && 2327 pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE; i++) { 2328 pcdac_out[pcdac_i++] = pcdac_tmp[i]; 2329 pwr_idx++; 2330 } 2331 2332 /* Extrapolate above maximum */ 2333 while (pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE) 2334 pcdac_out[pcdac_i++] = pcdac_n; 2335 2336} 2337 2338/* 2339 * Combine available XPD Curves and fill Linear Power to PCDAC table 2340 * on RF5112 2341 * 2342 * RFX112 can have up to 2 curves (one for low txpower range and one for 2343 * higher txpower range). We need to put them both on pcdac_out and place 2344 * them in the correct location. In case we only have one curve available 2345 * just fit it on pcdac_out (it's supposed to cover the entire range of 2346 * available pwr levels since it's always the higher power curve). Extrapolate 2347 * below and above final table if needed. 2348 */ 2349static void 2350ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min, 2351 s16 *table_max, u8 pdcurves) 2352{ 2353 u8 *pcdac_out = ah->ah_txpower.txp_pd_table; 2354 u8 *pcdac_low_pwr; 2355 u8 *pcdac_high_pwr; 2356 u8 *pcdac_tmp; 2357 u8 pwr; 2358 s16 max_pwr_idx; 2359 s16 min_pwr_idx; 2360 s16 mid_pwr_idx = 0; 2361 /* Edge flag turs on the 7nth bit on the PCDAC 2362 * to delcare the higher power curve (force values 2363 * to be greater than 64). If we only have one curve 2364 * we don't need to set this, if we have 2 curves and 2365 * fill the table backwards this can also be used to 2366 * switch from higher power curve to lower power curve */ 2367 u8 edge_flag; 2368 int i; 2369 2370 /* When we have only one curve available 2371 * that's the higher power curve. If we have 2372 * two curves the first is the high power curve 2373 * and the next is the low power curve. */ 2374 if (pdcurves > 1) { 2375 pcdac_low_pwr = ah->ah_txpower.tmpL[1]; 2376 pcdac_high_pwr = ah->ah_txpower.tmpL[0]; 2377 mid_pwr_idx = table_max[1] - table_min[1] - 1; 2378 max_pwr_idx = (table_max[0] - table_min[0]) / 2; 2379 2380 /* If table size goes beyond 31.5dB, keep the 2381 * upper 31.5dB range when setting tx power. 2382 * Note: 126 = 31.5 dB in quarter dB steps */ 2383 if (table_max[0] - table_min[1] > 126) 2384 min_pwr_idx = table_max[0] - 126; 2385 else 2386 min_pwr_idx = table_min[1]; 2387 2388 /* Since we fill table backwards 2389 * start from high power curve */ 2390 pcdac_tmp = pcdac_high_pwr; 2391 2392 edge_flag = 0x40; 2393 } else { 2394 pcdac_low_pwr = ah->ah_txpower.tmpL[1]; /* Zeroed */ 2395 pcdac_high_pwr = ah->ah_txpower.tmpL[0]; 2396 min_pwr_idx = table_min[0]; 2397 max_pwr_idx = (table_max[0] - table_min[0]) / 2; 2398 pcdac_tmp = pcdac_high_pwr; 2399 edge_flag = 0; 2400 } 2401 2402 /* This is used when setting tx power*/ 2403 ah->ah_txpower.txp_min_idx = min_pwr_idx/2; 2404 2405 /* Fill Power to PCDAC table backwards */ 2406 pwr = max_pwr_idx; 2407 for (i = 63; i >= 0; i--) { 2408 /* Entering lower power range, reset 2409 * edge flag and set pcdac_tmp to lower 2410 * power curve.*/ 2411 if (edge_flag == 0x40 && 2412 (2*pwr <= (table_max[1] - table_min[0]) || pwr == 0)) { 2413 edge_flag = 0x00; 2414 pcdac_tmp = pcdac_low_pwr; 2415 pwr = mid_pwr_idx/2; 2416 } 2417 2418 /* Don't go below 1, extrapolate below if we have 2419 * already swithced to the lower power curve -or 2420 * we only have one curve and edge_flag is zero 2421 * anyway */ 2422 if (pcdac_tmp[pwr] < 1 && (edge_flag == 0x00)) { 2423 while (i >= 0) { 2424 pcdac_out[i] = pcdac_out[i + 1]; 2425 i--; 2426 } 2427 break; 2428 } 2429 2430 pcdac_out[i] = pcdac_tmp[pwr] | edge_flag; 2431 2432 /* Extrapolate above if pcdac is greater than 2433 * 126 -this can happen because we OR pcdac_out 2434 * value with edge_flag on high power curve */ 2435 if (pcdac_out[i] > 126) 2436 pcdac_out[i] = 126; 2437 2438 /* Decrease by a 0.5dB step */ 2439 pwr--; 2440 } 2441} 2442 2443/* Write PCDAC values on hw */ 2444static void 2445ath5k_setup_pcdac_table(struct ath5k_hw *ah) 2446{ 2447 u8 *pcdac_out = ah->ah_txpower.txp_pd_table; 2448 int i; 2449 2450 /* 2451 * Write TX power values 2452 */ 2453 for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) { 2454 ath5k_hw_reg_write(ah, 2455 (((pcdac_out[2*i + 0] << 8 | 0xff) & 0xffff) << 0) | 2456 (((pcdac_out[2*i + 1] << 8 | 0xff) & 0xffff) << 16), 2457 AR5K_PHY_PCDAC_TXPOWER(i)); 2458 } 2459} 2460 2461 2462/* 2463 * Power to PDADC table functions 2464 */ 2465 2466/* 2467 * Set the gain boundaries and create final Power to PDADC table 2468 * 2469 * We can have up to 4 pd curves, we need to do a simmilar process 2470 * as we do for RF5112. This time we don't have an edge_flag but we 2471 * set the gain boundaries on a separate register. 2472 */ 2473static void 2474ath5k_combine_pwr_to_pdadc_curves(struct ath5k_hw *ah, 2475 s16 *pwr_min, s16 *pwr_max, u8 pdcurves) 2476{ 2477 u8 gain_boundaries[AR5K_EEPROM_N_PD_GAINS]; 2478 u8 *pdadc_out = ah->ah_txpower.txp_pd_table; 2479 u8 *pdadc_tmp; 2480 s16 pdadc_0; 2481 u8 pdadc_i, pdadc_n, pwr_step, pdg, max_idx, table_size; 2482 u8 pd_gain_overlap; 2483 2484 /* Note: Register value is initialized on initvals 2485 * there is no feedback from hw. 2486 * XXX: What about pd_gain_overlap from EEPROM ? */ 2487 pd_gain_overlap = (u8) ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG5) & 2488 AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP; 2489 2490 /* Create final PDADC table */ 2491 for (pdg = 0, pdadc_i = 0; pdg < pdcurves; pdg++) { 2492 pdadc_tmp = ah->ah_txpower.tmpL[pdg]; 2493 2494 if (pdg == pdcurves - 1) 2495 /* 2 dB boundary stretch for last 2496 * (higher power) curve */ 2497 gain_boundaries[pdg] = pwr_max[pdg] + 4; 2498 else 2499 /* Set gain boundary in the middle 2500 * between this curve and the next one */ 2501 gain_boundaries[pdg] = 2502 (pwr_max[pdg] + pwr_min[pdg + 1]) / 2; 2503 2504 /* Sanity check in case our 2 db stretch got out of 2505 * range. */ 2506 if (gain_boundaries[pdg] > AR5K_TUNE_MAX_TXPOWER) 2507 gain_boundaries[pdg] = AR5K_TUNE_MAX_TXPOWER; 2508 2509 /* For the first curve (lower power) 2510 * start from 0 dB */ 2511 if (pdg == 0) 2512 pdadc_0 = 0; 2513 else 2514 /* For the other curves use the gain overlap */ 2515 pdadc_0 = (gain_boundaries[pdg - 1] - pwr_min[pdg]) - 2516 pd_gain_overlap; 2517 2518 /* Force each power step to be at least 0.5 dB */ 2519 if ((pdadc_tmp[1] - pdadc_tmp[0]) > 1) 2520 pwr_step = pdadc_tmp[1] - pdadc_tmp[0]; 2521 else 2522 pwr_step = 1; 2523 2524 /* If pdadc_0 is negative, we need to extrapolate 2525 * below this pdgain by a number of pwr_steps */ 2526 while ((pdadc_0 < 0) && (pdadc_i < 128)) { 2527 s16 tmp = pdadc_tmp[0] + pdadc_0 * pwr_step; 2528 pdadc_out[pdadc_i++] = (tmp < 0) ? 0 : (u8) tmp; 2529 pdadc_0++; 2530 } 2531 2532 /* Set last pwr level, using gain boundaries */ 2533 pdadc_n = gain_boundaries[pdg] + pd_gain_overlap - pwr_min[pdg]; 2534 /* Limit it to be inside pwr range */ 2535 table_size = pwr_max[pdg] - pwr_min[pdg]; 2536 max_idx = (pdadc_n < table_size) ? pdadc_n : table_size; 2537 2538 /* Fill pdadc_out table */ 2539 while (pdadc_0 < max_idx && pdadc_i < 128) 2540 pdadc_out[pdadc_i++] = pdadc_tmp[pdadc_0++]; 2541 2542 /* Need to extrapolate above this pdgain? */ 2543 if (pdadc_n <= max_idx) 2544 continue; 2545 2546 /* Force each power step to be at least 0.5 dB */ 2547 if ((pdadc_tmp[table_size - 1] - pdadc_tmp[table_size - 2]) > 1) 2548 pwr_step = pdadc_tmp[table_size - 1] - 2549 pdadc_tmp[table_size - 2]; 2550 else 2551 pwr_step = 1; 2552 2553 /* Extrapolate above */ 2554 while ((pdadc_0 < (s16) pdadc_n) && 2555 (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2)) { 2556 s16 tmp = pdadc_tmp[table_size - 1] + 2557 (pdadc_0 - max_idx) * pwr_step; 2558 pdadc_out[pdadc_i++] = (tmp > 127) ? 127 : (u8) tmp; 2559 pdadc_0++; 2560 } 2561 } 2562 2563 while (pdg < AR5K_EEPROM_N_PD_GAINS) { 2564 gain_boundaries[pdg] = gain_boundaries[pdg - 1]; 2565 pdg++; 2566 } 2567 2568 while (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2) { 2569 pdadc_out[pdadc_i] = pdadc_out[pdadc_i - 1]; 2570 pdadc_i++; 2571 } 2572 2573 /* Set gain boundaries */ 2574 ath5k_hw_reg_write(ah, 2575 AR5K_REG_SM(pd_gain_overlap, 2576 AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP) | 2577 AR5K_REG_SM(gain_boundaries[0], 2578 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_1) | 2579 AR5K_REG_SM(gain_boundaries[1], 2580 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_2) | 2581 AR5K_REG_SM(gain_boundaries[2], 2582 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_3) | 2583 AR5K_REG_SM(gain_boundaries[3], 2584 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_4), 2585 AR5K_PHY_TPC_RG5); 2586 2587 /* Used for setting rate power table */ 2588 ah->ah_txpower.txp_min_idx = pwr_min[0]; 2589 2590} 2591 2592/* Write PDADC values on hw */ 2593static void 2594ath5k_setup_pwr_to_pdadc_table(struct ath5k_hw *ah, 2595 u8 pdcurves, u8 *pdg_to_idx) 2596{ 2597 u8 *pdadc_out = ah->ah_txpower.txp_pd_table; 2598 u32 reg; 2599 u8 i; 2600 2601 /* Select the right pdgain curves */ 2602 2603 /* Clear current settings */ 2604 reg = ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG1); 2605 reg &= ~(AR5K_PHY_TPC_RG1_PDGAIN_1 | 2606 AR5K_PHY_TPC_RG1_PDGAIN_2 | 2607 AR5K_PHY_TPC_RG1_PDGAIN_3 | 2608 AR5K_PHY_TPC_RG1_NUM_PD_GAIN); 2609 2610 /* 2611 * Use pd_gains curve from eeprom 2612 * 2613 * This overrides the default setting from initvals 2614 * in case some vendors (e.g. Zcomax) don't use the default 2615 * curves. If we don't honor their settings we 'll get a 2616 * 5dB (1 * gain overlap ?) drop. 2617 */ 2618 reg |= AR5K_REG_SM(pdcurves, AR5K_PHY_TPC_RG1_NUM_PD_GAIN); 2619 2620 switch (pdcurves) { 2621 case 3: 2622 reg |= AR5K_REG_SM(pdg_to_idx[2], AR5K_PHY_TPC_RG1_PDGAIN_3); 2623 /* Fall through */ 2624 case 2: 2625 reg |= AR5K_REG_SM(pdg_to_idx[1], AR5K_PHY_TPC_RG1_PDGAIN_2); 2626 /* Fall through */ 2627 case 1: 2628 reg |= AR5K_REG_SM(pdg_to_idx[0], AR5K_PHY_TPC_RG1_PDGAIN_1); 2629 break; 2630 } 2631 ath5k_hw_reg_write(ah, reg, AR5K_PHY_TPC_RG1); 2632 2633 /* 2634 * Write TX power values 2635 */ 2636 for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) { 2637 ath5k_hw_reg_write(ah, 2638 ((pdadc_out[4*i + 0] & 0xff) << 0) | 2639 ((pdadc_out[4*i + 1] & 0xff) << 8) | 2640 ((pdadc_out[4*i + 2] & 0xff) << 16) | 2641 ((pdadc_out[4*i + 3] & 0xff) << 24), 2642 AR5K_PHY_PDADC_TXPOWER(i)); 2643 } 2644} 2645 2646 2647/* 2648 * Common code for PCDAC/PDADC tables 2649 */ 2650 2651/* 2652 * This is the main function that uses all of the above 2653 * to set PCDAC/PDADC table on hw for the current channel. 2654 * This table is used for tx power calibration on the basband, 2655 * without it we get weird tx power levels and in some cases 2656 * distorted spectral mask 2657 */ 2658static int 2659ath5k_setup_channel_powertable(struct ath5k_hw *ah, 2660 struct ieee80211_channel *channel, 2661 u8 ee_mode, u8 type) 2662{ 2663 struct ath5k_pdgain_info *pdg_L, *pdg_R; 2664 struct ath5k_chan_pcal_info *pcinfo_L; 2665 struct ath5k_chan_pcal_info *pcinfo_R; 2666 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; 2667 u8 *pdg_curve_to_idx = ee->ee_pdc_to_idx[ee_mode]; 2668 s16 table_min[AR5K_EEPROM_N_PD_GAINS]; 2669 s16 table_max[AR5K_EEPROM_N_PD_GAINS]; 2670 u8 *tmpL; 2671 u8 *tmpR; 2672 u32 target = channel->center_freq; 2673 int pdg, i; 2674 2675 /* Get surounding freq piers for this channel */ 2676 ath5k_get_chan_pcal_surrounding_piers(ah, channel, 2677 &pcinfo_L, 2678 &pcinfo_R); 2679 2680 /* Loop over pd gain curves on 2681 * surounding freq piers by index */ 2682 for (pdg = 0; pdg < ee->ee_pd_gains[ee_mode]; pdg++) { 2683 2684 /* Fill curves in reverse order 2685 * from lower power (max gain) 2686 * to higher power. Use curve -> idx 2687 * backmapping we did on eeprom init */ 2688 u8 idx = pdg_curve_to_idx[pdg]; 2689 2690 /* Grab the needed curves by index */ 2691 pdg_L = &pcinfo_L->pd_curves[idx]; 2692 pdg_R = &pcinfo_R->pd_curves[idx]; 2693 2694 /* Initialize the temp tables */ 2695 tmpL = ah->ah_txpower.tmpL[pdg]; 2696 tmpR = ah->ah_txpower.tmpR[pdg]; 2697 2698 /* Set curve's x boundaries and create 2699 * curves so that they cover the same 2700 * range (if we don't do that one table 2701 * will have values on some range and the 2702 * other one won't have any so interpolation 2703 * will fail) */ 2704 table_min[pdg] = min(pdg_L->pd_pwr[0], 2705 pdg_R->pd_pwr[0]) / 2; 2706 2707 table_max[pdg] = max(pdg_L->pd_pwr[pdg_L->pd_points - 1], 2708 pdg_R->pd_pwr[pdg_R->pd_points - 1]) / 2; 2709 2710 /* Now create the curves on surrounding channels 2711 * and interpolate if needed to get the final 2712 * curve for this gain on this channel */ 2713 switch (type) { 2714 case AR5K_PWRTABLE_LINEAR_PCDAC: 2715 /* Override min/max so that we don't loose 2716 * accuracy (don't divide by 2) */ 2717 table_min[pdg] = min(pdg_L->pd_pwr[0], 2718 pdg_R->pd_pwr[0]); 2719 2720 table_max[pdg] = 2721 max(pdg_L->pd_pwr[pdg_L->pd_points - 1], 2722 pdg_R->pd_pwr[pdg_R->pd_points - 1]); 2723 2724 /* Override minimum so that we don't get 2725 * out of bounds while extrapolating 2726 * below. Don't do this when we have 2 2727 * curves and we are on the high power curve 2728 * because table_min is ok in this case */ 2729 if (!(ee->ee_pd_gains[ee_mode] > 1 && pdg == 0)) { 2730 2731 table_min[pdg] = 2732 ath5k_get_linear_pcdac_min(pdg_L->pd_step, 2733 pdg_R->pd_step, 2734 pdg_L->pd_pwr, 2735 pdg_R->pd_pwr); 2736 2737 /* Don't go too low because we will 2738 * miss the upper part of the curve. 2739 * Note: 126 = 31.5dB (max power supported) 2740 * in 0.25dB units */ 2741 if (table_max[pdg] - table_min[pdg] > 126) 2742 table_min[pdg] = table_max[pdg] - 126; 2743 } 2744 2745 /* Fall through */ 2746 case AR5K_PWRTABLE_PWR_TO_PCDAC: 2747 case AR5K_PWRTABLE_PWR_TO_PDADC: 2748 2749 ath5k_create_power_curve(table_min[pdg], 2750 table_max[pdg], 2751 pdg_L->pd_pwr, 2752 pdg_L->pd_step, 2753 pdg_L->pd_points, tmpL, type); 2754 2755 /* We are in a calibration 2756 * pier, no need to interpolate 2757 * between freq piers */ 2758 if (pcinfo_L == pcinfo_R) 2759 continue; 2760 2761 ath5k_create_power_curve(table_min[pdg], 2762 table_max[pdg], 2763 pdg_R->pd_pwr, 2764 pdg_R->pd_step, 2765 pdg_R->pd_points, tmpR, type); 2766 break; 2767 default: 2768 return -EINVAL; 2769 } 2770 2771 /* Interpolate between curves 2772 * of surounding freq piers to 2773 * get the final curve for this 2774 * pd gain. Re-use tmpL for interpolation 2775 * output */ 2776 for (i = 0; (i < (u16) (table_max[pdg] - table_min[pdg])) && 2777 (i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) { 2778 tmpL[i] = (u8) ath5k_get_interpolated_value(target, 2779 (s16) pcinfo_L->freq, 2780 (s16) pcinfo_R->freq, 2781 (s16) tmpL[i], 2782 (s16) tmpR[i]); 2783 } 2784 } 2785 2786 /* Now we have a set of curves for this 2787 * channel on tmpL (x range is table_max - table_min 2788 * and y values are tmpL[pdg][]) sorted in the same 2789 * order as EEPROM (because we've used the backmapping). 2790 * So for RF5112 it's from higher power to lower power 2791 * and for RF2413 it's from lower power to higher power. 2792 * For RF5111 we only have one curve. */ 2793 2794 /* Fill min and max power levels for this 2795 * channel by interpolating the values on 2796 * surounding channels to complete the dataset */ 2797 ah->ah_txpower.txp_min_pwr = ath5k_get_interpolated_value(target, 2798 (s16) pcinfo_L->freq, 2799 (s16) pcinfo_R->freq, 2800 pcinfo_L->min_pwr, pcinfo_R->min_pwr); 2801 2802 ah->ah_txpower.txp_max_pwr = ath5k_get_interpolated_value(target, 2803 (s16) pcinfo_L->freq, 2804 (s16) pcinfo_R->freq, 2805 pcinfo_L->max_pwr, pcinfo_R->max_pwr); 2806 2807 /* We are ready to go, fill PCDAC/PDADC 2808 * table and write settings on hardware */ 2809 switch (type) { 2810 case AR5K_PWRTABLE_LINEAR_PCDAC: 2811 /* For RF5112 we can have one or two curves 2812 * and each curve covers a certain power lvl 2813 * range so we need to do some more processing */ 2814 ath5k_combine_linear_pcdac_curves(ah, table_min, table_max, 2815 ee->ee_pd_gains[ee_mode]); 2816 2817 /* Set txp.offset so that we can 2818 * match max power value with max 2819 * table index */ 2820 ah->ah_txpower.txp_offset = 64 - (table_max[0] / 2); 2821 2822 /* Write settings on hw */ 2823 ath5k_setup_pcdac_table(ah); 2824 break; 2825 case AR5K_PWRTABLE_PWR_TO_PCDAC: 2826 /* We are done for RF5111 since it has only 2827 * one curve, just fit the curve on the table */ 2828 ath5k_fill_pwr_to_pcdac_table(ah, table_min, table_max); 2829 2830 /* No rate powertable adjustment for RF5111 */ 2831 ah->ah_txpower.txp_min_idx = 0; 2832 ah->ah_txpower.txp_offset = 0; 2833 2834 /* Write settings on hw */ 2835 ath5k_setup_pcdac_table(ah); 2836 break; 2837 case AR5K_PWRTABLE_PWR_TO_PDADC: 2838 /* Set PDADC boundaries and fill 2839 * final PDADC table */ 2840 ath5k_combine_pwr_to_pdadc_curves(ah, table_min, table_max, 2841 ee->ee_pd_gains[ee_mode]); 2842 2843 /* Write settings on hw */ 2844 ath5k_setup_pwr_to_pdadc_table(ah, pdg, pdg_curve_to_idx); 2845 2846 /* Set txp.offset, note that table_min 2847 * can be negative */ 2848 ah->ah_txpower.txp_offset = table_min[0]; 2849 break; 2850 default: 2851 return -EINVAL; 2852 } 2853 2854 return 0; 2855} 2856 2857 2858/* 2859 * Per-rate tx power setting 2860 * 2861 * This is the code that sets the desired tx power (below 2862 * maximum) on hw for each rate (we also have TPC that sets 2863 * power per packet). We do that by providing an index on the 2864 * PCDAC/PDADC table we set up. 2865 */ 2866 2867/* 2868 * Set rate power table 2869 * 2870 * For now we only limit txpower based on maximum tx power 2871 * supported by hw (what's inside rate_info). We need to limit 2872 * this even more, based on regulatory domain etc. 2873 * 2874 * Rate power table contains indices to PCDAC/PDADC table (0.5dB steps) 2875 * and is indexed as follows: 2876 * rates[0] - rates[7] -> OFDM rates 2877 * rates[8] - rates[14] -> CCK rates 2878 * rates[15] -> XR rates (they all have the same power) 2879 */ 2880static void 2881ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr, 2882 struct ath5k_rate_pcal_info *rate_info, 2883 u8 ee_mode) 2884{ 2885 unsigned int i; 2886 u16 *rates; 2887 2888 /* max_pwr is power level we got from driver/user in 0.5dB 2889 * units, switch to 0.25dB units so we can compare */ 2890 max_pwr *= 2; 2891 max_pwr = min(max_pwr, (u16) ah->ah_txpower.txp_max_pwr) / 2; 2892 2893 /* apply rate limits */ 2894 rates = ah->ah_txpower.txp_rates_power_table; 2895 2896 /* OFDM rates 6 to 24Mb/s */ 2897 for (i = 0; i < 5; i++) 2898 rates[i] = min(max_pwr, rate_info->target_power_6to24); 2899 2900 /* Rest OFDM rates */ 2901 rates[5] = min(rates[0], rate_info->target_power_36); 2902 rates[6] = min(rates[0], rate_info->target_power_48); 2903 rates[7] = min(rates[0], rate_info->target_power_54); 2904 2905 /* CCK rates */ 2906 /* 1L */ 2907 rates[8] = min(rates[0], rate_info->target_power_6to24); 2908 /* 2L */ 2909 rates[9] = min(rates[0], rate_info->target_power_36); 2910 /* 2S */ 2911 rates[10] = min(rates[0], rate_info->target_power_36); 2912 /* 5L */ 2913 rates[11] = min(rates[0], rate_info->target_power_48); 2914 /* 5S */ 2915 rates[12] = min(rates[0], rate_info->target_power_48); 2916 /* 11L */ 2917 rates[13] = min(rates[0], rate_info->target_power_54); 2918 /* 11S */ 2919 rates[14] = min(rates[0], rate_info->target_power_54); 2920 2921 /* XR rates */ 2922 rates[15] = min(rates[0], rate_info->target_power_6to24); 2923 2924 /* CCK rates have different peak to average ratio 2925 * so we have to tweak their power so that gainf 2926 * correction works ok. For this we use OFDM to 2927 * CCK delta from eeprom */ 2928 if ((ee_mode == AR5K_EEPROM_MODE_11G) && 2929 (ah->ah_phy_revision < AR5K_SREV_PHY_5212A)) 2930 for (i = 8; i <= 15; i++) 2931 rates[i] -= ah->ah_txpower.txp_cck_ofdm_gainf_delta; 2932 2933 /* Now that we have all rates setup use table offset to 2934 * match the power range set by user with the power indices 2935 * on PCDAC/PDADC table */ 2936 for (i = 0; i < 16; i++) { 2937 rates[i] += ah->ah_txpower.txp_offset; 2938 /* Don't get out of bounds */ 2939 if (rates[i] > 63) 2940 rates[i] = 63; 2941 } 2942 2943 /* Min/max in 0.25dB units */ 2944 ah->ah_txpower.txp_min_pwr = 2 * rates[7]; 2945 ah->ah_txpower.txp_max_pwr = 2 * rates[0]; 2946 ah->ah_txpower.txp_ofdm = rates[7]; 2947} 2948 2949 2950/* 2951 * Set transmition power 2952 */ 2953int 2954ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, 2955 u8 ee_mode, u8 txpower) 2956{ 2957 struct ath5k_rate_pcal_info rate_info; 2958 u8 type; 2959 int ret; 2960 2961 if (txpower > AR5K_TUNE_MAX_TXPOWER) { 2962 ATH5K_ERR(ah->ah_sc, "invalid tx power: %u\n", txpower); 2963 return -EINVAL; 2964 } 2965 2966 /* Reset TX power values */ 2967 memset(&ah->ah_txpower, 0, sizeof(ah->ah_txpower)); 2968 ah->ah_txpower.txp_tpc = AR5K_TUNE_TPC_TXPOWER; 2969 ah->ah_txpower.txp_min_pwr = 0; 2970 ah->ah_txpower.txp_max_pwr = AR5K_TUNE_MAX_TXPOWER; 2971 2972 /* Initialize TX power table */ 2973 switch (ah->ah_radio) { 2974 case AR5K_RF5111: 2975 type = AR5K_PWRTABLE_PWR_TO_PCDAC; 2976 break; 2977 case AR5K_RF5112: 2978 type = AR5K_PWRTABLE_LINEAR_PCDAC; 2979 break; 2980 case AR5K_RF2413: 2981 case AR5K_RF5413: 2982 case AR5K_RF2316: 2983 case AR5K_RF2317: 2984 case AR5K_RF2425: 2985 type = AR5K_PWRTABLE_PWR_TO_PDADC; 2986 break; 2987 default: 2988 return -EINVAL; 2989 } 2990 2991 /* FIXME: Only on channel/mode change */ 2992 ret = ath5k_setup_channel_powertable(ah, channel, ee_mode, type); 2993 if (ret) 2994 return ret; 2995 2996 /* Limit max power if we have a CTL available */ 2997 ath5k_get_max_ctl_power(ah, channel); 2998 2999 /* FIXME: Tx power limit for this regdomain 3000 * XXX: Mac80211/CRDA will do that anyway ? */ 3001 3002 /* FIXME: Antenna reduction stuff */ 3003 3004 /* FIXME: Limit power on turbo modes */ 3005 3006 /* FIXME: TPC scale reduction */ 3007 3008 /* Get surounding channels for per-rate power table 3009 * calibration */ 3010 ath5k_get_rate_pcal_data(ah, channel, &rate_info); 3011 3012 /* Setup rate power table */ 3013 ath5k_setup_rate_powertable(ah, txpower, &rate_info, ee_mode); 3014 3015 /* Write rate power table on hw */ 3016 ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(3, 24) | 3017 AR5K_TXPOWER_OFDM(2, 16) | AR5K_TXPOWER_OFDM(1, 8) | 3018 AR5K_TXPOWER_OFDM(0, 0), AR5K_PHY_TXPOWER_RATE1); 3019 3020 ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(7, 24) | 3021 AR5K_TXPOWER_OFDM(6, 16) | AR5K_TXPOWER_OFDM(5, 8) | 3022 AR5K_TXPOWER_OFDM(4, 0), AR5K_PHY_TXPOWER_RATE2); 3023 3024 ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(10, 24) | 3025 AR5K_TXPOWER_CCK(9, 16) | AR5K_TXPOWER_CCK(15, 8) | 3026 AR5K_TXPOWER_CCK(8, 0), AR5K_PHY_TXPOWER_RATE3); 3027 3028 ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(14, 24) | 3029 AR5K_TXPOWER_CCK(13, 16) | AR5K_TXPOWER_CCK(12, 8) | 3030 AR5K_TXPOWER_CCK(11, 0), AR5K_PHY_TXPOWER_RATE4); 3031 3032 /* FIXME: TPC support */ 3033 if (ah->ah_txpower.txp_tpc) { 3034 ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX_TPC_ENABLE | 3035 AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX); 3036 3037 ath5k_hw_reg_write(ah, 3038 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_ACK) | 3039 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CTS) | 3040 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CHIRP), 3041 AR5K_TPC); 3042 } else { 3043 ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX | 3044 AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX); 3045 } 3046 3047 return 0; 3048} 3049 3050int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower) 3051{ 3052 /*Just a try M.F.*/ 3053 struct ieee80211_channel *channel = ah->ah_current_channel; 3054 u8 ee_mode; 3055 3056 switch (channel->hw_value & CHANNEL_MODES) { 3057 case CHANNEL_A: 3058 case CHANNEL_T: 3059 case CHANNEL_XR: 3060 ee_mode = AR5K_EEPROM_MODE_11A; 3061 break; 3062 case CHANNEL_G: 3063 case CHANNEL_TG: 3064 ee_mode = AR5K_EEPROM_MODE_11G; 3065 break; 3066 case CHANNEL_B: 3067 ee_mode = AR5K_EEPROM_MODE_11B; 3068 break; 3069 default: 3070 ATH5K_ERR(ah->ah_sc, 3071 "invalid channel: %d\n", channel->center_freq); 3072 return -EINVAL; 3073 } 3074 3075 ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_TXPOWER, 3076 "changing txpower to %d\n", txpower); 3077 3078 return ath5k_hw_txpower(ah, channel, ee_mode, txpower); 3079} 3080