[go: nahoru, domu]

Video Decoder performance tests

The video decoder performance tests are a set of tests used to measure the performance of various video decoder implementations. These tests run directly on top of the video decoder implementation, and don't require the full Chrome browser stack. They are build on top of the GoogleTest framework.

Running from Tast

The Tast framework provides an easy way to run the video decoder performance tests from a ChromeOS chroot. Test data is automatically deployed to the device being tested. To run all video decoder performance tests use:

tast run $HOST video.DecodeAccelPerf*

Wildcards can be used to run specific sets of tests:

  • Run all VP8 performance tests: tast run $HOST video.DecodeAccelPerfVP8*
  • Run all 1080p 60fps performance tests: tast run $HOST video.DecodeAccelPerf*1080P60FPS

Check the tast video folder for a list of all available tests. See the Tast quickstart guide for more information about the Tast framework.

Running manually

To run the video decoder performance tests manually the video_decode_accelerator_perf_tests target needs to be built and deployed to the device being tested. Running the video decoder performance tests can be done by executing:

./video_decode_accelerator_perf_tests [<video path>] [<video metadata path>]

e.g.: ./video_decode_accelerator_perf_tests test-25fps.h264

Test videos: Test videos are present for multiple codecs in the media/test/data folder in Chromium's source tree (e.g. test-25fps.vp8). If no video is specified test-25fps.h264 will be used.

Video Metadata: These videos also have an accompanying metadata .json file that needs to be deployed alongside the test video. They can also be found in the media/test/data folder (e.g. test-25fps.h264.json). If no metadata file is specified <video path>.json will be used. The video metadata file contains info about the video such as its codec profile, dimensions and number of frames.

Note: Various CPU scaling and thermal throttling mechanisms might be active on the device (e.g. scaling_governor, intel_pstate). As these can influence test results it's advised to disable them.

Performance metrics

To measure decoder performance two different test scenarios are used.

Uncapped decoder performance: In this scenario the specified test video is decoded from start to finish as fast as possible. This test scenario provides an estimate of the decoder's maximum performance (e.g. the maximum FPS).

Capped decoder performance: This scenario simulates a more realistic environment by decoding a video from start to finish at its actual frame rate, while simulating real-time rendering. Frames that are not decoded by the time they should be rendered will be dropped.

Various performance metrics are collected by these tests:

  • FPS: The average number of frames the decoder was able to decode per second.
  • Frames Dropped: The number of frames that were dropped during playback, only relevant for the capped performance test.
  • Dropped frame percentage: The percentage of frames dropped, only relevant for the capped performance test.
  • Frame delivery time: The time between subsequent frame deliveries. The average frame delivery time and 25/50/75 percentiles are calculated.
  • Frame decode time: The time between scheduling a frame to be decoded and getting the decoded frame. This metric provides a measure of the decoder's latency. The average decode time and 25/50/75 percentiles are calculated.

All performance metrics are written to perf_metrics/<test_name>.json.

Command line options

Multiple command line arguments can be given to the command:

 -v                  enable verbose mode, e.g. -v=2.
--vmodule            enable verbose mode for the specified module,
                     e.g. --vmodule=*media/gpu*=2.
--output_folder      overwrite the output folder used to store
                     performance metrics, if not specified results
                     will be stored in the current working directory.
--use-legacy         use the legacy VDA-based video decoders.\n"
--use_vd             use the new VD-based video decoders.\n"
                     (enabled by default)\n"
--use_vd_vda         use the new VD-based video decoders with a wrapper
                     that translates to the VDA interface, used to test
                     interaction with older components expecting the VDA
                     interface.
--gtest_help         display the gtest help and exit.
--help               display this help and exit.

Source code

See the video decoder performance tests source code.